cmd: Remove mmc_spi command

The mmc_spi command was added to manually setup MMC over SPI bus
using command. This was required by the legacy non-DM MMC_SPI driver.

With DM based MMC_SPI driver in-place, we can now use all general
storge commands and mmc command for MMC over SPI bus hence we remove
the mmc_spi command all it's references.

Suggested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

5 files changed, 0 insertions, 100 deletions

diff --git a/cmd/Kconfig b/cmd/Kconfig
index 7f6bca81a9..67284d8a5f 100644
--- a/cmd/Kconfig
+++ b/cmd/Kconfig
@@ -955,15 +955,6 @@ config CMD_NVME
 	help
 	  NVM Express device support
 
-config CMD_MMC_SPI
-	bool "mmc_spi - Set up MMC SPI device"
-	help
-	  Provides a way to set up an MMC (Multimedia Card) SPI (Serial
-	  Peripheral Interface) device. The device provides a means of
-	  accessing an MMC device via SPI using a single data line, limited
-	  to 20MHz. It is useful since it reduces the amount of protocol code
-	  required.
-
 config CMD_ONENAND
 	bool "onenand - access to onenand device"
 	help
diff --git a/cmd/Makefile b/cmd/Makefile
index 49e64cde1d..0aa3741453 100644
--- a/cmd/Makefile
+++ b/cmd/Makefile
@@ -93,7 +93,6 @@ obj-$(CONFIG_CMD_MII) += mdio.o
 endif
 obj-$(CONFIG_CMD_MISC) += misc.o
 obj-$(CONFIG_CMD_MMC) += mmc.o
-obj-$(CONFIG_CMD_MMC_SPI) += mmc_spi.o
 obj-$(CONFIG_MP) += mp.o
 obj-$(CONFIG_CMD_MTD) += mtd.o
 obj-$(CONFIG_CMD_MTDPARTS) += mtdparts.o
diff --git a/cmd/mmc_spi.c b/cmd/mmc_spi.c
deleted file mode 100644
index 0c44d06817..0000000000
--- a/cmd/mmc_spi.c
+++ /dev/null
@@ -1,88 +0,0 @@
-/*
- * Command for mmc_spi setup.
- *
- * Copyright (C) 2010 Thomas Chou <thomas@wytron.com.tw>
- * Licensed under the GPL-2 or later.
- */
-
-#include <common.h>
-#include <mmc.h>
-#include <spi.h>
-
-#ifndef CONFIG_MMC_SPI_BUS
-# define CONFIG_MMC_SPI_BUS 0
-#endif
-#ifndef CONFIG_MMC_SPI_CS
-# define CONFIG_MMC_SPI_CS 1
-#endif
-/* in SPI mode, MMC speed limit is 20MHz, while SD speed limit is 25MHz */
-#ifndef CONFIG_MMC_SPI_SPEED
-# define CONFIG_MMC_SPI_SPEED 25000000
-#endif
-/* MMC and SD specs only seem to care that sampling is on the
- * rising edge ... meaning SPI modes 0 or 3.  So either SPI mode
- * should be legit.  We'll use mode 0 since the steady state is 0,
- * which is appropriate for hotplugging, unless the platform data
- * specify mode 3 (if hardware is not compatible to mode 0).
- */
-#ifndef CONFIG_MMC_SPI_MODE
-# define CONFIG_MMC_SPI_MODE SPI_MODE_0
-#endif
-
-static int do_mmc_spi(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-	uint bus = CONFIG_MMC_SPI_BUS;
-	uint cs = CONFIG_MMC_SPI_CS;
-	uint speed = CONFIG_MMC_SPI_SPEED;
-	uint mode = CONFIG_MMC_SPI_MODE;
-	char *endp;
-	struct mmc *mmc;
-
-	if (argc < 2)
-		goto usage;
-
-	cs = simple_strtoul(argv[1], &endp, 0);
-	if (*argv[1] == 0 || (*endp != 0 && *endp != ':'))
-		goto usage;
-	if (*endp == ':') {
-		if (endp[1] == 0)
-			goto usage;
-		bus = cs;
-		cs = simple_strtoul(endp + 1, &endp, 0);
-		if (*endp != 0)
-			goto usage;
-	}
-	if (argc >= 3) {
-		speed = simple_strtoul(argv[2], &endp, 0);
-		if (*argv[2] == 0 || *endp != 0)
-			goto usage;
-	}
-	if (argc >= 4) {
-		mode = simple_strtoul(argv[3], &endp, 16);
-		if (*argv[3] == 0 || *endp != 0)
-			goto usage;
-	}
-	if (!spi_cs_is_valid(bus, cs)) {
-		printf("Invalid SPI bus %u cs %u\n", bus, cs);
-		return 1;
-	}
-
-	mmc = mmc_spi_init(bus, cs, speed, mode);
-	if (!mmc) {
-		printf("Failed to create MMC Device\n");
-		return 1;
-	}
-	printf("%s: %d at %u:%u hz %u mode %u\n", mmc->cfg->name,
-	       mmc->block_dev.devnum, bus, cs, speed, mode);
-	mmc_init(mmc);
-	return 0;
-
-usage:
-	return CMD_RET_USAGE;
-}
-
-U_BOOT_CMD(
-	mmc_spi,	4,	0,	do_mmc_spi,
-	"mmc_spi setup",
-	"[bus:]cs [hz] [mode]	- setup mmc_spi device"
-);
diff --git a/include/configs/UCP1020.h b/include/configs/UCP1020.h
index 268a41c82c..6a01a90425 100644
--- a/include/configs/UCP1020.h
+++ b/include/configs/UCP1020.h
@@ -438,7 +438,6 @@
 
 #ifdef CONFIG_MMC
 #define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_MMC_SPI
 #endif
 
 /* Misc Extra Settings */
diff --git a/include/mmc.h b/include/mmc.h
index 032873c2ff..0ef891f5c2 100644
--- a/include/mmc.h
+++ b/include/mmc.h
@@ -824,7 +824,6 @@ void mmc_set_preinit(struct mmc *mmc, int preinit);
 #else
 #define mmc_host_is_spi(mmc)	0
 #endif
-struct mmc *mmc_spi_init(uint bus, uint cs, uint speed, uint mode);
 
 void board_mmc_power_init(void);
 int board_mmc_init(bd_t *bis);