summaryrefslogtreecommitdiff
path: root/include
diff options
context:
space:
mode:
Diffstat (limited to 'include')
-rw-r--r--include/configs/ML2.h257
1 files changed, 0 insertions, 257 deletions
diff --git a/include/configs/ML2.h b/include/configs/ML2.h
deleted file mode 100644
index 4df9f4cbc5..0000000000
--- a/include/configs/ML2.h
+++ /dev/null
@@ -1,257 +0,0 @@
-/*
- * ML2.h: ML2 specific config options
- *
- * Copyright 2002 Mind NV
- *
- * http://www.mind.be/
- *
- * Author : Peter De Schrijver (p2@mind.be)
- *
- * Derived from : other configuration header files in this tree
- *
- * This software may be used and distributed according to the terms of
- * the GNU General Public License (GPL) version 2, incorporated herein by
- * reference. Drivers based on or derived from this code fall under the GPL
- * and must retain the authorship, copyright and this license notice. This
- * file is not a complete program and may only be used when the entire
- * program is licensed under the GPL.
- *
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405 1 /* This is a PPC405 CPU */
-#define CONFIG_4xx 1 /* ...member of PPC4xx family */
-#define CONFIG_ML2 1 /* ...on a ML2 board */
-
-#define CONFIG_SYS_TEXT_BASE 0x18000000
-#define CONFIG_SYS_LDSCRIPT "board/ml2/u-boot.lds"
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-
-#ifdef CONFIG_ENV_IS_IN_NVRAM
-#undef CONFIG_ENV_IS_IN_FLASH
-#else
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#undef CONFIG_ENV_IS_IN_NVRAM
-#endif
-#endif
-
-#define CONFIG_BAUDRATE 9600
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-
-#if 1
-#define CONFIG_BOOTCOMMAND "bootm" /* autoboot command */
-#else
-#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
-#endif
-
-#define CONFIG_PREBOOT "fsload 0x00100000 /boot/image"
-
-#if 0
-#define CONFIG_BOOTARGS "root=/dev/nfs " \
- "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 " \
- "nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4"
-#else
-#define CONFIG_BOOTARGS "root=/dev/mtdblock2 " \
- "console=ttyS0 console=tty"
-
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_KGDB
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_JFFS2
-
-#undef CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_RTC
-#undef CONFIG_CMD_PCI
-#undef CONFIG_CMD_I2C
-
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-#define CONFIG_SYS_CLK_FREQ 50000000
-
-#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
-
-/*
- * I2C
- */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_SPEED 400000
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-/*
- * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
- * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
- * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
- * The Linux BASE_BAUD define should match this configuration.
- * baseBaud = cpuClock/(uartDivisor*16)
- * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
- * set Linux BASE_BAUD to 403200.
- */
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
-#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
-
-#define CONFIG_SYS_BASE_BAUD (3125000*16)
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_BASE_BAUD
-#define CONFIG_SYS_DUART_CHAN 0
-#define CONFIG_SYS_NS16550_COM1 0xa0001003
-#define CONFIG_SYS_NS16550_COM2 0xa0011003
-#define CONFIG_SYS_NS16550_REG_SIZE -4
-#define CONFIG_SYS_NS16550 1
-#define CONFIG_SYS_INIT_CHAN1 1
-#define CONFIG_SYS_INIT_CHAN2 1
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x18000000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-/* BEG ENVIRONNEMENT FLASH */
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_OFFSET 0x00050000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
-#endif
-/* END ENVIRONNEMENT FLASH */
-/*-----------------------------------------------------------------------
- * NVRAM organization
- */
-#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
-#define CONFIG_SYS_NVRAM_SIZE 0x1ff8 /* NVRAM size */
-
-#ifdef CONFIG_ENV_IS_IN_NVRAM
-#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */
-#define CONFIG_ENV_ADDR \
- (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */
-#endif
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
-
-
-/* Configuration Port location */
-#define CONFIG_PORT_ADDR 0xF0000500
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-
-#define CONFIG_SYS_INIT_RAM_ADDR 0x800000 /* inside of SDRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Definitions for Serial Presence Detect EEPROM address
- * (to get SDRAM settings)
- */
-#define SPD_EEPROM_ADDRESS 0x50
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition, whole device */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV "nor0"
-#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET 0x00080000
-
-/* mtdparts command line support */
-/* Note: fake mtd_id used, no linux mtd map file */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT "nor0=ml2-0"
-#define MTDPARTS_DEFAULT "mtdparts=ml2-0:-@512k(jffs2)"
-*/
-
-#endif /* __CONFIG_H */