summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--arch/powerpc/cpu/mpc8xx/cpu_init.c16
-rw-r--r--arch/powerpc/cpu/mpc8xx/scc.c4
-rw-r--r--arch/powerpc/cpu/mpc8xx/serial.c4
-rw-r--r--arch/powerpc/include/asm/immap_512x.h1
-rw-r--r--board/mbx8xx/Makefile8
-rw-r--r--board/mbx8xx/README68
-rw-r--r--board/mbx8xx/csr.h44
-rw-r--r--board/mbx8xx/dimm.h98
-rw-r--r--board/mbx8xx/flash.c392
-rw-r--r--board/mbx8xx/mbx8xx.c383
-rw-r--r--board/mbx8xx/pcmcia.c156
-rw-r--r--board/mbx8xx/u-boot.lds82
-rw-r--r--board/mbx8xx/u-boot.lds.debug122
-rw-r--r--board/mbx8xx/vpd.c180
-rw-r--r--board/mbx8xx/vpd.h119
-rw-r--r--boards.cfg2
-rw-r--r--doc/README.scrapyard1
-rw-r--r--include/common.h7
-rw-r--r--include/commproc.h32
-rw-r--r--include/configs/MBX.h290
-rw-r--r--include/configs/MBX860T.h395
-rw-r--r--post/cpu/mpc8xx/ether.c4
-rw-r--r--post/cpu/mpc8xx/uart.c4
23 files changed, 1 insertions, 2411 deletions
diff --git a/arch/powerpc/cpu/mpc8xx/cpu_init.c b/arch/powerpc/cpu/mpc8xx/cpu_init.c
index 53f873d1ab..69455c7be0 100644
--- a/arch/powerpc/cpu/mpc8xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc8xx/cpu_init.c
@@ -29,12 +29,10 @@ void cpm_load_patch (volatile immap_t * immr);
*/
void cpu_init_f (volatile immap_t * immr)
{
-#ifndef CONFIG_MBX
volatile memctl8xx_t *memctl = &immr->im_memctl;
# ifdef CONFIG_SYS_PLPRCR
ulong mfmask;
# endif
-#endif
ulong reg;
/* SYPCR - contains watchdog control (11-9) */
@@ -74,8 +72,6 @@ void cpu_init_f (volatile immap_t * immr)
immr->im_clkrstk.cark_plprcrk = KAPWR_KEY;
-#ifndef CONFIG_MBX /* MBX board does things different */
-
/* If CONFIG_SYS_PLPRCR (set in the various *_config.h files) tries to
* set the MF field, then just copy CONFIG_SYS_PLPRCR over car_plprcr,
* otherwise OR in CONFIG_SYS_PLPRCR so we do not change the current MF
@@ -203,8 +199,6 @@ void cpu_init_f (volatile immap_t * immr)
memctl->memc_br7 = CONFIG_SYS_BR7_PRELIM;
#endif
-#endif /* ! CONFIG_MBX */
-
/*
* Reset CPM
*/
@@ -213,16 +207,6 @@ void cpu_init_f (volatile immap_t * immr)
__asm__ ("eieio");
} while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
-#ifdef CONFIG_MBX
- /*
- * on the MBX, things are a little bit different:
- * - we need to read the VPD to get board information
- * - the plprcr is set up dynamically
- * - the memory controller is set up dynamically
- */
- mbx_init ();
-#endif /* CONFIG_MBX */
-
#ifdef CONFIG_RPXCLASSIC
rpxclassic_init ();
#endif
diff --git a/arch/powerpc/cpu/mpc8xx/scc.c b/arch/powerpc/cpu/mpc8xx/scc.c
index 2ef77b4c14..94c9969e3f 100644
--- a/arch/powerpc/cpu/mpc8xx/scc.c
+++ b/arch/powerpc/cpu/mpc8xx/scc.c
@@ -492,10 +492,6 @@ static int scc_init (struct eth_device *dev, bd_t * bis)
immr->im_cpm.cp_pbdat &= ~0x00000010;
#endif /* QS860T */
-#ifdef CONFIG_MBX
- board_ether_init ();
-#endif
-
#if defined(CONFIG_NETVIA)
#if defined(PA_ENET_PDN)
immr->im_ioport.iop_papar &= ~PA_ENET_PDN;
diff --git a/arch/powerpc/cpu/mpc8xx/serial.c b/arch/powerpc/cpu/mpc8xx/serial.c
index 4e840498d7..cb48ed942f 100644
--- a/arch/powerpc/cpu/mpc8xx/serial.c
+++ b/arch/powerpc/cpu/mpc8xx/serial.c
@@ -225,10 +225,6 @@ static int smc_init (void)
up->smc_tstate = 0;
#endif
-#if defined(CONFIG_MBX)
- board_serial_init();
-#endif /* CONFIG_MBX */
-
/* Set UART mode, 8 bit, no parity, one stop.
* Enable receive and transmit.
*/
diff --git a/arch/powerpc/include/asm/immap_512x.h b/arch/powerpc/include/asm/immap_512x.h
index bed80aa933..6086a73ba9 100644
--- a/arch/powerpc/include/asm/immap_512x.h
+++ b/arch/powerpc/include/asm/immap_512x.h
@@ -59,7 +59,6 @@ typedef struct sysconf512x {
u8 res2[0x28];
law512x_t ddrlaw; /* DDR Local Access Window */
u8 res3[0x18];
- u32 mbxbar; /* MBX Base Address */
u32 srambar; /* SRAM Base Address */
u32 nfcbar; /* NFC Base Address */
u8 res4[0x34];
diff --git a/board/mbx8xx/Makefile b/board/mbx8xx/Makefile
deleted file mode 100644
index 2074b6b904..0000000000
--- a/board/mbx8xx/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = mbx8xx.o flash.o vpd.o pcmcia.o
diff --git a/board/mbx8xx/README b/board/mbx8xx/README
deleted file mode 100644
index c889fe9791..0000000000
--- a/board/mbx8xx/README
+++ /dev/null
@@ -1,68 +0,0 @@
-IMPORTANT NOTE - read before defining CONFIG_SYS_USE_OSCCLK in your board
- config file!!!
-
-
-WARNING: Wrong settings of this parameter have the potential to
-damage hardware by running the MBX's CPU at frequencies that exceed
-it's rating and/or overdriving the it's SPLL!
-
-
-Ramblings:
-1) Motorola offered 12 different variants of the MBX, 6 823s and 6 860s.
-2) Of these 12 variants, only 2 were entry level boards.
-3) I believe that the 2 entry level boards were the only ones that
- used OSCM clocking. I can't be completely certain of this at this
- point.
-4) Motorola never offered an MBX that ran faster than 50Mhz.
-5) The 10, non-entry level boards, ran at 40Mhz.
-6) The EXTCLK input has a minimum clock of 15Mhz for the 823/860.
-7) Motorola no longer sells MBXs.
-
-Based on this information, I can surmise that the default power-on
-reset clocking was one of the following three options.
-
-Multiplier SPLL Options
-------------------------------------
-513 OSCM is SPLL input
-5 OSCM is SPLL input
-1 EXTCLK is SPLL input
-
-The forth option:
-
-5 EXTCLK is SPLL input
-
-is not possible on MBXs. This is because the minimum EXTCLK input
-frequency is 15Mhz. 5 * 15Mhz = 75 Mhz. There was no variant that ran
-above 50 Mhz.
-
-The board I have borrowed definitely uses a multiplier of 1 for
-EXTCLK and runs at 40Mhz. I even went so far as to put a scope on it.
-
-One of the two default OSCM modes are most likely what was used on
-the entry level boards to cheapen them by eliminating the external
-crystal oscillator.
-
-To add insult to injury, the stupid 860 PLPRCR register retains it's
-multiplication factor through hard resets. You can't clear it out
-because it is battery backed and once it is set wrong, it stays
-wrong. The only way to reset it, so that it takes on it's default
-multiplier is to disconnect all power including external, batteries,
-as well discharging caps on the board. This precludes the fact that
-your 860 may be quite DEAD by this time!
-
-If you don't setup the multiplication factor for boards that use the
-OSCM input, they won't run correctly, but at least they won't be
-dead.
-
-Addtionally, there is no good way to determine the clock input source
-from CPU register data. The only way to deal with this is either hard
-code it, determine the correct value with some rather NASTY timing
-loops, or try to grok it from external data sources. Motorola
-firmware opts for the NASTY timing loops, but needs to configure the
-serial ports to do so.
-
-
-You may have a legitimate need to define CONFIG_SYS_USE_OSCCLK if your
-MBX8xx board is using the OSCM clocking mode.
-
-You better know what you are doing here.
diff --git a/board/mbx8xx/csr.h b/board/mbx8xx/csr.h
deleted file mode 100644
index 937060973e..0000000000
--- a/board/mbx8xx/csr.h
+++ /dev/null
@@ -1,44 +0,0 @@
-#ifndef __csr_h
-#define __csr_h
-
-/*
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * Control and Status Register definitions for the MBX
- *
- *--------------------------------------------------------------------
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/* bits for control register #1 / status register #1 */
-#define CSR1_ETEN 0x80 /* Ethernet Transceiver Enabled */
-#define CSR1_ELEN 0x40 /* Ethernet XCVR in Internal Loopback */
-#define CSR1_EAEN 0x20 /* Auto selection TP/AUI Enabled */
-#define CSR1_TPEN 0x10 /* TP manually selected */
-#define CSR1_FDDIS 0x08 /* Full Duplex Mode disabled */
-#define CSR1_FCTEN 0x04 /* Collision Testing of XCVR disabled */
-#define CSR1_COM1EN 0x02 /* COM1 signals routed to RS232 Transceiver */
-#define CSR1_XCVRDIS 0x01 /* Onboard RS232 Transceiver Disabled */
-
-/* bits for control register #2 */
-#define CR2_VDDSEL 0xC0 /* PCMCIA Supply Voltage */
-#define CR2_VPPSEL 0x30 /* PCMCIA Programming Voltage */
-#define CR2_BRDFAIL 0x08 /* Board fail */
-#define CR2_SWS1 0x04 /* Software Status #2 LED */
-#define CR2_SWS2 0x02 /* Software Status #2 LED */
-#define CR2_QSPANRST 0x01 /* Reset QSPAN */
-
-/* bits for status register #2 */
-#define SR2_VDDSEL 0xC0 /* PCMCIA Supply Voltage */
-#define SR2_VPPSEL 0x30 /* PCMCIA Programming Voltage */
-#define SR2_BATGD 0x08 /* Low Voltage indication for onboard bat */
-#define SR2_NVBATGD 0x04 /* Low Voltage indication for NVRAM */
-#define SR2_RDY 0x02 /* Flash programming status bit */
-#define SR2_FT 0x01 /* Reserved for Factory test purposes */
-
-#define MBX_CSR1 (*((uchar *)CONFIG_SYS_CSR_BASE))
-#define MBX_CSR2 (*((uchar *)CONFIG_SYS_CSR_BASE + 1))
-
-#endif /* __csr_h */
diff --git a/board/mbx8xx/dimm.h b/board/mbx8xx/dimm.h
deleted file mode 100644
index b40f112356..0000000000
--- a/board/mbx8xx/dimm.h
+++ /dev/null
@@ -1,98 +0,0 @@
-#ifndef __dimm_h
-#define __dimm_h
-
-/*
- * Module name: %M%
- * Description:
- * Serial Presence Detect Definitions Module
- * SCCS identification: %I%
- * Branch: %B%
- * Sequence: %S%
- * Date newest applied delta was created (MM/DD/YY): %G%
- * Time newest applied delta was created (HH:MM:SS): %U%
- * SCCS file name %F%
- * Fully qualified SCCS file name:
- * %P%
- * Copyright:
- * (C) COPYRIGHT MOTOROLA, INC. 1996
- * ALL RIGHTS RESERVED
- * Notes:
- * 1. All data was taken from an IBM application note titled
- * "Serial Presence Detect Definitions".
- * History:
- * Date Who
- *
- * 10/24/96 Rob Baxter
- * Initial release.
- *
- */
-
-/*
- * serial PD byte assignment address map (256 byte EEPROM)
- */
-typedef struct dimm
-{
- uchar n_bytes; /* 00 number of bytes written/used */
- uchar t_bytes; /* 01 total number of bytes in serial PD device */
- uchar fmt; /* 02 fundamental memory type (FPM/EDO/SDRAM) */
- uchar n_row; /* 03 number of rows */
- uchar n_col; /* 04 number of columns */
- uchar n_banks; /* 05 number of banks */
- uchar data_w_lo; /* 06 data width */
- uchar data_w_hi; /* 07 data width */
- uchar ifl; /* 08 interface levels */
- uchar a_ras; /* 09 RAS access */
- uchar a_cas; /* 0A CAS access */
- uchar ct; /* 0B configuration type (non-parity/parity/ECC) */
- uchar refresh_rt; /* 0C refresh rate/type */
- uchar p_dram_o; /* 0D primary DRAM organization */
- uchar s_dram_o; /* 0E secondary DRAM organization (parity/ECC-checkbits) */
- uchar reserved[17]; /* 0F reserved fields for future offerings */
- uchar ss_info[32]; /* 20 superset information (may be used in the future) */
- uchar m_info[64]; /* 40 manufacturer information (optional) */
- uchar unused[128]; /* 80 unused storage locations */
-} dimm_t;
-
-/*
- * memory type definitions
- */
-#define DIMM_MT_FPM 1 /* standard FPM (fast page mode) DRAM */
-#define DIMM_MT_EDO 2 /* EDO (extended data out) */
-#define DIMM_MT_PN 3 /* pipelined nibble */
-#define DIMM_MT_SDRAM 4 /* SDRAM (synchronous DRAM) */
-
-/*
- * row addresses definitions
- */
-#define DIMM_RA_RDNDNT (1<<7) /* redundant addressing */
-#define DIMM_RA_MASK 0x7f /* number of row addresses mask */
-
-/*
- * module interface levels definitions
- */
-#define DIMM_IFL_TTL 0 /* TTL/5V tolerant */
-#define DIMM_IFL_LVTTL 1 /* LVTTL (not 5V tolerant) */
-#define DIMM_IFL_HSTL15 2 /* HSTL 1.5 */
-#define DIMM_IFL_SSTL33 3 /* SSTL 3.3 */
-#define DIMM_IFL_SSTL25 4 /* SSTL 2.5 */
-
-/*
- * DIMM configuration type definitions
- */
-#define DIMM_CT_NONE 0 /* none */
-#define DIMM_CT_PARITY 1 /* parity */
-#define DIMM_CT_ECC 2 /* ECC */
-
-/*
- * row addresses definitions
- */
-#define DIMM_RRT_SR (1<<7) /* self refresh flag */
-#define DIMM_RRT_MASK 0x7f /* refresh rate mask */
-#define DIMM_RRT_NRML 0x00 /* normal (15.625us) */
-#define DIMM_RRT_R_3_9 0x01 /* reduced .25x (3.9us) */
-#define DIMM_RRT_R_7_8 0x02 /* reduced .5x (7.8us) */
-#define DIMM_RRT_E_31_3 0x03 /* extended 2x (31.3us) */
-#define DIMM_RRT_E_62_5 0x04 /* extended 4x (62.5us) */
-#define DIMM_RRT_E_125 0x05 /* extended 8x (125us) */
-
-#endif /* __dimm_h */
diff --git a/board/mbx8xx/flash.c b/board/mbx8xx/flash.c
deleted file mode 100644
index fa07152cc8..0000000000
--- a/board/mbx8xx/flash.c
+++ /dev/null
@@ -1,392 +0,0 @@
-/*
- * (C) Copyright 2000
- * Marius Groeger <mgroeger@sysgo.de>
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * Flash Routines for AM290[48]0B devices
- *
- *--------------------------------------------------------------------
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-#include "vpd.h"
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-
-static ulong flash_get_size (vu_long *addr, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- unsigned long size, totsize;
- int i;
- ulong addr;
-
- /* Init: no FLASHes known */
- for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- }
-
- totsize = 0;
- addr = 0xfc000000;
- for(i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
- size = flash_get_size((vu_long *)addr, &flash_info[i]);
- if (flash_info[i].flash_id == FLASH_UNKNOWN)
- break;
- totsize += size;
- addr += size;
- }
-
- addr = 0xfe000000;
- for(i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
-
- size = flash_get_size((vu_long *)addr, &flash_info[i]);
- if (flash_info[i].flash_id == FLASH_UNKNOWN)
- break;
- totsize += size;
- addr += size;
- }
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
- &flash_info[0]);
-#endif
-
- return (totsize);
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id >> 16) {
- case 0x1:
- printf ("AMD ");
- break;
- default:
- printf ("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case AMD_ID_F040B:
- printf ("AM29F040B (4 Mbit)\n");
- break;
- case AMD_ID_F080B:
- printf ("AM29F080B (8 Mbit)\n");
- break;
- case AMD_ID_F016D:
- printf ("AM29F016D (16 Mbit)\n");
- break;
- default:
- printf ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i=0; i<info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " "
- );
- }
- printf ("\n");
- return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (vu_long *addr, flash_info_t *info)
-{
- short i;
- ulong vendor, devid;
- ulong base = (ulong)addr;
-
- /* Write auto select command: read Manufacturer ID */
- addr[0x0555] = 0xAAAAAAAA;
- addr[0x02AA] = 0x55555555;
- addr[0x0555] = 0x90909090;
-
- vendor = addr[0];
- devid = addr[1] & 0xff;
-
- /* only support AMD */
- if (vendor != 0x01010101) {
- return 0;
- }
-
- vendor &= 0xf;
- devid &= 0xff;
-
- if (devid == AMD_ID_F040B) {
- info->flash_id = vendor << 16 | devid;
- info->sector_count = 8;
- info->size = info->sector_count * 0x10000;
- }
- else if (devid == AMD_ID_F080B) {
- info->flash_id = vendor << 16 | devid;
- info->sector_count = 16;
- info->size = 4 * info->sector_count * 0x10000;
- }
- else if (devid == AMD_ID_F016D) {
- info->flash_id = vendor << 16 | devid;
- info->sector_count = 32;
- info->size = 4 * info->sector_count * 0x10000;
- }
- else {
- printf ("## Unknown Flash Type: %08lx\n", devid);
- return 0;
- }
-
- /* check for protected sectors */
- for (i = 0; i < info->sector_count; i++) {
- /* sector base address */
- info->start[i] = base + i * (info->size / info->sector_count);
- /* read sector protection at sector address, (A7 .. A0) = 0x02 */
- /* D0 = 1 if protected */
- addr = (volatile unsigned long *)(info->start[i]);
- info->protect[i] = addr[2] & 1;
- }
-
- /*
- * Prevent writes to uninitialized FLASH.
- */
- if (info->flash_id != FLASH_UNKNOWN) {
- addr = (vu_long *)info->start[0];
- addr[0] = 0xF0; /* reset bank */
- }
-
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- vu_long *addr = (vu_long*)(info->start[0]);
- int flag, prot, sect, l_sect;
- ulong start, now, last;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- l_sect = -1;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[0x0555] = 0XAAAAAAAA;
- addr[0x02AA] = 0x55555555;
- addr[0x0555] = 0x80808080;
- addr[0x0555] = 0XAAAAAAAA;
- addr[0x02AA] = 0x55555555;
-
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- addr = (vu_long*)(info->start[sect]);
- addr[0] = 0x30303030;
- l_sect = sect;
- }
- }
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- /*
- * We wait for the last triggered sector
- */
- if (l_sect < 0)
- goto DONE;
-
- start = get_timer (0);
- last = start;
- addr = (vu_long*)(info->start[l_sect]);
- while ((addr[0] & 0x80808080) != 0x80808080) {
- if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- return 1;
- }
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- serial_putc ('.');
- last = now;
- }
- }
-
- DONE:
- /* reset to read mode */
- addr = (volatile unsigned long *)info->start[0];
- addr[0] = 0xF0F0F0F0; /* reset bank */
-
- printf (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
-
- wp = (addr & ~3); /* get lower word aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i=0, cp=wp; i<l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
- for (; i<4 && cnt>0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt==0 && i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= 4) {
- data = 0;
- for (i=0; i<4; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_word(info, wp, data)) != 0) {
- return (rc);
- }
- wp += 4;
- cnt -= 4;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i<4; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- return (write_word(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
- vu_long *addr = (vu_long*)(info->start[0]);
- ulong start;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*((vu_long *)dest) & data) != data) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- addr[0x0555] = 0xAAAAAAAA;
- addr[0x02AA] = 0x55555555;
- addr[0x0555] = 0xA0A0A0A0;
-
- *((vu_long *)dest) = data;
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* data polling for D7 */
- start = get_timer (0);
- while ((*((vu_long *)dest) & 0x80808080) != (data & 0x80808080)) {
- if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- return (1);
- }
- }
- return (0);
-}
-
-/*-----------------------------------------------------------------------
- */
diff --git a/board/mbx8xx/mbx8xx.c b/board/mbx8xx/mbx8xx.c
deleted file mode 100644
index 98c723f047..0000000000
--- a/board/mbx8xx/mbx8xx.c
+++ /dev/null
@@ -1,383 +0,0 @@
-/*
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * Board specific routines for the MBX
- *
- * - initialisation
- * - interface to VPD data (mac address, clock speeds)
- * - memory controller
- * - serial io initialisation
- * - ethernet io initialisation
- *
- * -----------------------------------------------------------------
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <commproc.h>
-#include <mpc8xx.h>
-#include <net.h>
-#include "dimm.h"
-#include "vpd.h"
-#include "csr.h"
-
-/* ------------------------------------------------------------------------- */
-
-static const uint sdram_table_40[] = {
- /* DRAM - single read. (offset 0 in upm RAM)
- */
- 0xCFAFC004, 0x0FAFC404, 0x0CAF0C04, 0x30AF0C00,
- 0xF1BF4805, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
- /* DRAM - burst read. (offset 8 in upm RAM)
- */
- 0xCFAFC004, 0x0FAFC404, 0x0CAF0C04, 0x03AF0C08,
- 0x0CAF0C04, 0x03AF0C08, 0x0CAF0C04, 0x03AF0C08,
- 0x0CAF0C04, 0x30AF0C00, 0xF3BF4805, 0xFFFFC005,
- 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
- /* DRAM - single write. (offset 18 in upm RAM)
- */
- 0xCFFF0004, 0x0FFF0404, 0x0CFF0C00, 0x33FF4804,
- 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
- /* DRAM - burst write. (offset 20 in upm RAM)
- */
- 0xCFFF0004, 0x0FFF0404, 0x0CFF0C00, 0x03FF0C0C,
- 0x0CFF0C00, 0x03FF0C0C, 0x0CFF0C00, 0x03FF0C0C,
- 0x0CFF0C00, 0x33FF4804, 0xFFFFC005, 0xFFFFC005,
- 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
- /* refresh (offset 30 in upm RAM)
- */
- 0xFCFFC004, 0xC0FFC004, 0x01FFC004, 0x0FFFC004,
- 0x3FFFC004, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
- 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
- /* exception. (offset 3c in upm RAM)
- */
- 0xFFFFC007, 0xFFFFC007, 0xFFFFC007, 0xFFFFC007,
-};
-
-static const uint sdram_table_50[] = {
- /* DRAM - single read. (offset 0 in upm RAM)
- */
- 0xCFAFC004, 0x0FAFC404, 0x0CAF8C04, 0x10AF0C04,
- 0xF0AF0C00, 0xF3BF4805, 0xFFFFC005, 0xFFFFC005,
-
- /* DRAM - burst read. (offset 8 in upm RAM)
- */
- 0xCFAFC004, 0X0FAFC404, 0X0CAF8C04, 0X00AF0C04,
- /* 0X07AF0C08, 0X0CAF0C04, 0X01AF0C04, 0X0FAF0C04, */
- 0X07AF0C08, 0X0CAF0C04, 0X01AF0C04, 0X0FAF0C08,
- 0X0CAF0C04, 0X01AF0C04, 0X0FAF0C08, 0X0CAF0C04,
- /* 0X10AF0C04, 0XF0AFC000, 0XF3FF4805, 0XFFFFC005, */
- 0X10AF0C04, 0XF0AFC000, 0XF3BF4805, 0XFFFFC005,
-
- /* DRAM - single write. (offset 18 in upm RAM)
- */
- 0xCFFF0004, 0x0FFF0404, 0x0CFF0C00, 0x13FF4804,
- 0xFFFFC004, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
- /* DRAM - burst write. (offset 20 in upm RAM)
- */
- 0xCFFF0004, 0x0FFF0404, 0x0CFF0C00, 0x03FF0C0C,
- 0x0CFF0C00, 0x03FF0C0C, 0x0CFF0C00, 0x03FF0C0C,
- 0x0CFF0C00, 0x13FF4804, 0xFFFFC004, 0xFFFFC005,
- 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
- /* refresh (offset 30 in upm RAM)
- */
- 0xFCFFC004, 0xC0FFC004, 0x01FFC004, 0x0FFFC004,
- 0x1FFFC004, 0xFFFFC004, 0xFFFFC005, 0xFFFFC005,
- 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
- /* exception. (offset 3c in upm RAM)
- */
- 0xFFFFC007, 0xFFFFC007, 0xFFFFC007, 0xFFFFC007,
-};
-
-/* ------------------------------------------------------------------------- */
-
-#ifdef CONFIG_SYS_USE_OSCCLK
-static unsigned int get_reffreq(void);
-#endif
-static unsigned int board_get_cpufreq(void);
-
-void mbx_init (void)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immr->im_memctl;
- ulong speed, plprcr, sccr;
- ulong br0_32 = memctl->memc_br0 & 0x400;
-
- /* real-time clock status and control register */
- immr->im_sitk.sitk_rtcsck = KAPWR_KEY;
- immr->im_sit.sit_rtcsc = 0x00C3;
-
- /* SIEL and SIMASK Registers (see MBX PRG 2-3) */
- immr->im_siu_conf.sc_simask = 0x00000000;
- immr->im_siu_conf.sc_siel = 0xAAAA0000;
- immr->im_siu_conf.sc_tesr = 0xFFFFFFFF;
-
- /*
- * Prepare access to i2c bus. The MBX offers 3 devices on the i2c bus:
- * 1. Vital Product Data (contains clock speeds, MAC address etc, see vpd.h)
- * 2. RAM Specs (see dimm.h)
- * 2. DIMM Specs (see dimm.h)
- */
- vpd_init ();
-
- /* system clock and reset control register */
- immr->im_clkrstk.cark_sccrk = KAPWR_KEY;
- sccr = immr->im_clkrst.car_sccr;
- sccr &= SCCR_MASK;
- sccr |= CONFIG_SYS_SCCR;
- immr->im_clkrst.car_sccr = sccr;
-
- speed = board_get_cpufreq ();
-
-#if ((CONFIG_SYS_PLPRCR & PLPRCR_MF_MSK) != 0)
- plprcr = CONFIG_SYS_PLPRCR;
-#else
- plprcr = immr->im_clkrst.car_plprcr;
- plprcr &= PLPRCR_MF_MSK; /* isolate MF field */
- plprcr |= CONFIG_SYS_PLPRCR; /* reset control bits */
-#endif
-
-#ifdef CONFIG_SYS_USE_OSCCLK /* See doc/README.MBX ! */
- plprcr |= ((speed + get_reffreq() / 2) / refclock - 1) << 20;
-#endif
-
- immr->im_clkrstk.cark_plprcrk = KAPWR_KEY;
- immr->im_clkrst.car_plprcr = plprcr;
-
- /*
- * preliminary setup of memory controller:
- * - map Flash, otherwise configuration/status
- * registers won't be accessible when read
- * by board_init_f.
- * - map NVRAM and configuation/status registers.
- * - map pci registers.
- * - DON'T map ram yet, this is done in initdram().
- */
- switch (speed / 1000000) {
- case 40:
- memctl->memc_br0 = 0xFE000000 | br0_32 | 1;
- memctl->memc_or0 = 0xFF800930;
- memctl->memc_or4 = CONFIG_SYS_NVRAM_OR | 0x920;
- memctl->memc_br4 = CONFIG_SYS_NVRAM_BASE | 0x401;
- break;
- case 50:
- memctl->memc_br0 = 0xFE000000 | br0_32 | 1;
- memctl->memc_or0 = 0xFF800940;
- memctl->memc_or4 = CONFIG_SYS_NVRAM_OR | 0x930;
- memctl->memc_br4 = CONFIG_SYS_NVRAM_BASE | 0x401;
- break;
- default:
- hang ();
- break;
- }
-#ifdef CONFIG_USE_PCI
- memctl->memc_or5 = CONFIG_SYS_PCIMEM_OR;
- memctl->memc_br5 = CONFIG_SYS_PCIMEM_BASE | 0x001;
- memctl->memc_or6 = CONFIG_SYS_PCIBRIDGE_OR;
- memctl->memc_br6 = CONFIG_SYS_PCIBRIDGE_BASE | 0x001;
-#endif
- /*
- * FIXME: I do not understand why I have to call this to
- * initialise the control register here before booting from
- * the PCMCIA card but if I do not the Linux kernel falls
- * over in a big heap. If you can answer this question I
- * would like to know about it.
- */
- board_ether_init();
-}
-
-void board_serial_init (void)
-{
- MBX_CSR1 &= ~(CSR1_COM1EN | CSR1_XCVRDIS);
-}
-
-void board_ether_init (void)
-{
- MBX_CSR1 &= ~(CSR1_EAEN | CSR1_ELEN);
- MBX_CSR1 |= CSR1_ETEN | CSR1_TPEN | CSR1_FDDIS;
-}
-
-static unsigned int board_get_cpufreq (void)
-{
-#ifndef CONFIG_8xx_GCLK_FREQ
- vpd_packet_t *packet;
- ulong *p;
-
- packet = vpd_find_packet (VPD_PID_ICS);
- p = (ulong *)packet->data;
- return *p;
-#else
- return((unsigned int)CONFIG_8xx_GCLK_FREQ );
-#endif /* CONFIG_8xx_GCLK_FREQ */
-}
-
-#ifdef CONFIG_SYS_USE_OSCCLK
-static unsigned int get_reffreq (void)
-{
- vpd_packet_t *packet;
- ulong *p;
-
- packet = vpd_find_packet (VPD_PID_RCS);
- p = (ulong *)packet->data;
- return *p;
-}
-#endif
-
-static void board_get_enetaddr(uchar *addr)
-{
- int i;
- vpd_packet_t *packet;
-
- packet = vpd_find_packet (VPD_PID_EA);
- for (i = 0; i < 6; i++)
- addr[i] = packet->data[i];
-}
-
-int misc_init_r(void)
-{
- uchar enetaddr[6];
-
- if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
- board_get_enetaddr(enetaddr);
- eth_setenv_enetaddr("ethaddr", enetaddr);
- }
-
- return 0;
-}
-
-/*
- * Check Board Identity:
- */
-
-int checkboard (void)
-{
- vpd_packet_t *packet;
- int i;
- const char *const fmt =
- "\n *** Warning: Low Battery Status - %s Battery ***";
-
- puts ("Board: ");
-
- packet = vpd_find_packet (VPD_PID_PID);
- for (i = 0; i < packet->size; i++) {
- serial_putc (packet->data[i]);
- }
- packet = vpd_find_packet (VPD_PID_MT);
- for (i = 0; i < packet->size; i++) {
- serial_putc (packet->data[i]);
- }
- serial_putc ('(');
- packet = vpd_find_packet (VPD_PID_FAN);
- for (i = 0; i < packet->size; i++) {
- serial_putc (packet->data[i]);
- }
- serial_putc (')');
-
- if (!(MBX_CSR2 & SR2_BATGD))
- printf (fmt, "On-Board");
- if (!(MBX_CSR2 & SR2_NVBATGD))
- printf (fmt, "NVRAM");
-
- serial_putc ('\n');
-
- return (0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-static ulong get_ramsize (dimm_t * dimm)
-{
- ulong size = 0;
-
- if (dimm->fmt == 1 || dimm->fmt == 2 || dimm->fmt == 3
- || dimm->fmt == 4) {
- size = (1 << (dimm->n_row + dimm->n_col)) * dimm->n_banks *
- ((dimm->data_w_hi << 8 | dimm->data_w_lo) / 8);
- }
-
- return size;
-}
-
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- unsigned long ram_sz = 0;
- unsigned long dimm_sz = 0;
- dimm_t vpd_dimm, vpd_dram;
- unsigned int speed = board_get_cpufreq () / 1000000;
-
- if (vpd_read (0xa2, (uchar *) & vpd_dimm, sizeof (vpd_dimm), 0) > 0) {
- dimm_sz = get_ramsize (&vpd_dimm);
- }
- if (vpd_read (0xa6, (uchar *) & vpd_dram, sizeof (vpd_dram), 0) > 0) {
- ram_sz = get_ramsize (&vpd_dram);
- }
-
- /*
- * Only initialize memory controller when running from FLASH.
- * When running from RAM, don't touch it.
- */
- if ((ulong) initdram & 0xff000000) {
- ulong dimm_bank;
- ulong br0_32 = memctl->memc_br0 & 0x400;
-
- switch (speed) {
- case 40:
- upmconfig (UPMA, (uint *) sdram_table_40,
- sizeof (sdram_table_40) / sizeof (uint));
- memctl->memc_mptpr = 0x0200;
- memctl->memc_mamr = dimm_sz ? 0x06801000 : 0x13801000;
- memctl->memc_or7 = 0xff800930;
- memctl->memc_br7 = 0xfc000000 | (br0_32 ^ br0_32) | 1;
- break;
- case 50:
- upmconfig (UPMA, (uint *) sdram_table_50,
- sizeof (sdram_table_50) / sizeof (uint));
- memctl->memc_mptpr = 0x0200;
- memctl->memc_mamr = dimm_sz ? 0x08801000 : 0x1880100;
- memctl->memc_or7 = 0xff800940;
- memctl->memc_br7 = 0xfc000000 | (br0_32 ^ br0_32) | 1;
- break;
- default:
- hang ();
- break;
- }
-
- /* now map ram and dimm, largest one first */
- dimm_bank = dimm_sz / 2;
- if (!dimm_sz) {
- memctl->memc_or1 = ~(ram_sz - 1) | 0x400;
- memctl->memc_br1 = CONFIG_SYS_SDRAM_BASE | 0x81;
- memctl->memc_br2 = 0;
- memctl->memc_br3 = 0;
- } else if (ram_sz > dimm_bank) {
- memctl->memc_or1 = ~(ram_sz - 1) | 0x400;
- memctl->memc_br1 = CONFIG_SYS_SDRAM_BASE | 0x81;
- memctl->memc_or2 = ~(dimm_bank - 1) | 0x400;
- memctl->memc_br2 = (CONFIG_SYS_SDRAM_BASE + ram_sz) | 0x81;
- memctl->memc_or3 = ~(dimm_bank - 1) | 0x400;
- memctl->memc_br3 = (CONFIG_SYS_SDRAM_BASE + ram_sz + dimm_bank) \
- | 0x81;
- } else {
- memctl->memc_or2 = ~(dimm_bank - 1) | 0x400;
- memctl->memc_br2 = CONFIG_SYS_SDRAM_BASE | 0x81;
- memctl->memc_or3 = ~(dimm_bank - 1) | 0x400;
- memctl->memc_br3 = (CONFIG_SYS_SDRAM_BASE + dimm_bank) | 0x81;
- memctl->memc_or1 = ~(ram_sz - 1) | 0x400;
- memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE + dimm_sz) | 0x81;
- }
- }
-
- return ram_sz + dimm_sz;
-}
diff --git a/board/mbx8xx/pcmcia.c b/board/mbx8xx/pcmcia.c
deleted file mode 100644
index 497e260a0a..0000000000
--- a/board/mbx8xx/pcmcia.c
+++ /dev/null
@@ -1,156 +0,0 @@
-#include <common.h>
-#include <mpc8xx.h>
-#include <pcmcia.h>
-
-#include "csr.h"
-
-#undef CONFIG_PCMCIA
-
-#if defined(CONFIG_CMD_PCMCIA)
-#define CONFIG_PCMCIA
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
-#define CONFIG_PCMCIA
-#endif
-
-#ifdef CONFIG_PCMCIA
-
-/* A lot of this has been taken from the RPX code in this file it works from me.
- I have added the voltage selection for the MBX board. */
-
-/* MBX voltage bit in control register #2 */
-#define CR2_VPP12 ((uchar)0x10)
-#define CR2_VPPVDD ((uchar)0x20)
-#define CR2_VDD5 ((uchar)0x40)
-#define CR2_VDD3 ((uchar)0x80)
-
-#define PCMCIA_BOARD_MSG "MBX860"
-
-int pcmcia_voltage_set (int slot, int vcc, int vpp)
-{
- uchar reg = 0;
-
- debug ("voltage_set: PCMCIA_BOARD_MSG Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A' + slot, vcc / 10, vcc % 10, vpp / 10, vcc % 10);
-
- switch (vcc) {
- case 0:
- break;
- case 33:
- reg |= CR2_VDD3;
- break;
- case 50:
- reg |= CR2_VDD5;
- break;
- default:
- return 1;
- }
-
- switch (vpp) {
- case 0:
- break;
- case 33:
- case 50:
- if (vcc == vpp) {
- reg |= CR2_VPPVDD;
- } else {
- return 1;
- }
- break;
- case 120:
- reg |= CR2_VPP12;
- break;
- default:
- return 1;
- }
-
- /* first, turn off all power */
- MBX_CSR2 &= ~(CR2_VDDSEL | CR2_VPPSEL);
-
- /* enable new powersettings */
- MBX_CSR2 |= reg;
- debug ("MBX_CSR2 read = 0x%02x\n", MBX_CSR2);
-
- return (0);
-}
-
-int pcmcia_hardware_enable (int slot)
-{
- volatile pcmconf8xx_t *pcmp;
- uint reg, mask;
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n",
- 'A' + slot);
-
- udelay (10000);
-
- pcmp = (pcmconf8xx_t *) (&(((immap_t *) CONFIG_SYS_IMMR)->im_pcmcia));
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX (_slot_) = reg;
- udelay (500);
-
- /* remove all power */
- pcmcia_voltage_set (slot, 0, 0);
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- mask = PCMCIA_VS1 (_slot_) | PCMCIA_VS2 (_slot_);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", reg,
- (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
- (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
-
- if ((reg & mask) == mask) {
- pcmcia_voltage_set (_slot_, 50, 0);
- printf (" 5.0V card found: ");
- } else {
- pcmcia_voltage_set (_slot_, 33, 0);
- printf (" 3.3V card found: ");
- }
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX (_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX (_slot_) = reg;
-
- udelay (250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
- }
-
-#if defined(CONFIG_CMD_PCMCIA)
-int pcmcia_hardware_disable (int slot)
-{
- return 0; /* No hardware to disable */
-}
-#endif
-
-#endif /* CONFIG_PCMCIA */
diff --git a/board/mbx8xx/u-boot.lds b/board/mbx8xx/u-boot.lds
deleted file mode 100644
index 0eb2fba00c..0000000000
--- a/board/mbx8xx/u-boot.lds
+++ /dev/null
@@ -1,82 +0,0 @@
-/*
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
diff --git a/board/mbx8xx/u-boot.lds.debug b/board/mbx8xx/u-boot.lds.debug
deleted file mode 100644
index 7cfed1f1d5..0000000000
--- a/board/mbx8xx/u-boot.lds.debug
+++ /dev/null
@@ -1,122 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .interp : { *(.interp) }
- .hash : { *(.hash) }
- .dynsym : { *(.dynsym) }
- .dynstr : { *(.dynstr) }
- .rel.text : { *(.rel.text) }
- .rela.text : { *(.rela.text) }
- .rel.data : { *(.rel.data) }
- .rela.data : { *(.rela.data) }
- .rel.rodata : { *(.rel.rodata) }
- .rela.rodata : { *(.rela.rodata) }
- .rel.got : { *(.rel.got) }
- .rela.got : { *(.rela.got) }
- .rel.ctors : { *(.rel.ctors) }
- .rela.ctors : { *(.rela.ctors) }
- .rel.dtors : { *(.rel.dtors) }
- .rela.dtors : { *(.rela.dtors) }
- .rel.bss : { *(.rel.bss) }
- .rela.bss : { *(.rela.bss) }
- .rel.plt : { *(.rel.plt) }
- .rela.plt : { *(.rela.plt) }
- .init : { *(.init) }
- .plt : { *(.plt) }
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- arch/powerpc/cpu/mpc8xx/start.o (.text)
- common/dlmalloc.o (.text)
- lib/vsprintf.o (.text)
- lib/crc32.o (.text)
- arch/powerpc/lib/extable.o (.text)
-
- . = env_offset;
- common/env_embedded.o(.text)
-
- *(.text)
- *(.got1)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(.rodata)
- *(.rodata1)
- *(.rodata.str1.4)
- *(.eh_frame)
- }
- .fini : { *(.fini) } =0
- .ctors : { *(.ctors) }
- .dtors : { *(.dtors) }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FFF) & 0xFFFFF000;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- *(.got)
- _GOT2_TABLE_ = .;
- *(.got2)
- _FIXUP_TABLE_ = .;
- *(.fixup)
- }
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data)
- *(.data1)
- *(.sdata)
- *(.sdata2)
- *(.dynamic)
- CONSTRUCTORS
- }
- _edata = .;
- PROVIDE (edata = .);
-
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(4096);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(4096);
- __init_end = .;
-
- __bss_start = .;
- .bss :
- {
- *(.sbss) *(.scommon)
- *(.dynbss)
- *(.bss)
- *(COMMON)
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
diff --git a/board/mbx8xx/vpd.c b/board/mbx8xx/vpd.c
deleted file mode 100644
index 1ba754ee23..0000000000
--- a/board/mbx8xx/vpd.c
+++ /dev/null
@@ -1,180 +0,0 @@
-/*
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * Code in faintly related to linux/arch/powerpc/8xx_io:
- * MPC8xx CPM I2C interface. Copyright (c) 1999 Dan Malek (dmalek@jlc.net).
- *
- * This file implements functions to read the MBX's Vital Product Data
- * (VPD). I can't use the more general i2c code in mpc8xx/... since I need
- * the VPD at a time where there is no RAM available yet. Hence the VPD is
- * read into a special area in the DPRAM (see config_MBX.h::CFG_DPRAMVPD).
- *
- * -----------------------------------------------------------------
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#ifdef CONFIG_8xx
-#include <commproc.h>
-#endif
-#include "vpd.h"
-
-/* Location of receive/transmit buffer descriptors
- * Allocate one transmit bd and one receive bd.
- * IIC_BD_FREE points to free bd space which we'll use as tx buffer.
- */
-#define IIC_BD_TX1 (BD_IIC_START + 0*sizeof(cbd_t))
-#define IIC_BD_TX2 (BD_IIC_START + 1*sizeof(cbd_t))
-#define IIC_BD_RX (BD_IIC_START + 2*sizeof(cbd_t))
-#define IIC_BD_FREE (BD_IIC_START + 3*sizeof(cbd_t))
-
-/* FIXME -- replace 0x2000 with offsetof */
-#define VPD_P ((vpd_t *)(CONFIG_SYS_IMMR + 0x2000 + CONFIG_SYS_DPRAMVPD))
-
-/* transmit/receive buffers */
-#define IIC_RX_LENGTH 128
-
-#define WITH_MICROCODE_PATCH
-
-vpd_packet_t * vpd_find_packet(u_char ident)
-{
- vpd_packet_t *packet;
- vpd_t *vpd = VPD_P;
-
- packet = (vpd_packet_t *)&vpd->packets;
- while ((packet->identifier != ident) && packet->identifier != 0xFF)
- {
- packet = (vpd_packet_t *)((char *)packet + packet->size + 2);
- }
- return packet;
-}
-
-void vpd_init(void)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = &(im->im_cpm);
- volatile i2c8xx_t *i2c = (i2c8xx_t *)&(im->im_i2c);
- volatile iic_t *iip;
-#ifdef WITH_MICROCODE_PATCH
- ulong reloc = 0;
-#endif
-
- iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
-
- /*
- * kludge: when running from flash, no microcode patch can be
- * installed. However, the DPMEM usually contains non-zero
- * garbage at the relocatable patch base location, so lets clear
- * it now. This way the rest of the code can support the microcode
- * patch dynamically.
- */
- if ((ulong)vpd_init & 0xff000000)
- iip->iic_rpbase = 0;
-
-#ifdef WITH_MICROCODE_PATCH
- /* Check for and use a microcode relocation patch. */
- if ((reloc = iip->iic_rpbase))
- iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
-#endif
- /* Initialize Port B IIC pins */
- cp->cp_pbpar |= 0x00000030;
- cp->cp_pbdir |= 0x00000030;
- cp->cp_pbodr |= 0x00000030;
-
- i2c->i2c_i2mod = 0x04; /* filter clock */
- i2c->i2c_i2add = 0x34; /* select an arbitrary (unique) address */
- i2c->i2c_i2brg = 0x07; /* make clock run maximum slow */
- i2c->i2c_i2cmr = 0x00; /* disable interrupts */
- i2c->i2c_i2cer = 0x1f; /* clear events */
- i2c->i2c_i2com = 0x01; /* configure i2c to work as master */
-
- if (vpd_read(0xa4, (uchar*)VPD_P, VPD_EEPROM_SIZE, 0) != VPD_EEPROM_SIZE)
- {
- hang();
- }
-}
-
-
-/* Read from I2C.
- * This is a two step process. First, we send the "dummy" write
- * to set the device offset for the read. Second, we perform
- * the read operation.
- */
-int vpd_read(uint iic_device, uchar *buf, int count, int offset)
-{
- volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- volatile cpm8xx_t *cp = &(im->im_cpm);
- volatile i2c8xx_t *i2c = (i2c8xx_t *)&(im->im_i2c);
- volatile iic_t *iip;
- volatile cbd_t *tbdf1, *tbdf2, *rbdf;
- uchar *tb;
- uchar event;
-#ifdef WITH_MICROCODE_PATCH
- ulong reloc = 0;
-#endif
-
- iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
-#ifdef WITH_MICROCODE_PATCH
- /* Check for and use a microcode relocation patch. */
- if ((reloc = iip->iic_rpbase))
- iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
-#endif
- tbdf1 = (cbd_t *)&cp->cp_dpmem[IIC_BD_TX1];
- tbdf2 = (cbd_t *)&cp->cp_dpmem[IIC_BD_TX2];
- rbdf = (cbd_t *)&cp->cp_dpmem[IIC_BD_RX];
-
- /* Send a "dummy write" operation. This is a write request with
- * only the offset sent, followed by another start condition.
- * This will ensure we start reading from the first location
- * of the EEPROM.
- */
- tb = (uchar*)&cp->cp_dpmem[IIC_BD_FREE];
- tb[0] = iic_device & 0xfe; /* device address */
- tb[1] = offset; /* offset */
- tbdf1->cbd_bufaddr = (uint)tb;
- tbdf1->cbd_datlen = 2;
- tbdf1->cbd_sc = 0x8400;
-
- tb += 2;
- tb[0] = iic_device | 1; /* device address */
- tbdf2->cbd_bufaddr = (uint)tb;
- tbdf2->cbd_datlen = count+1;
- tbdf2->cbd_sc = 0xbc00;
-
- rbdf->cbd_bufaddr = (uint)buf;
- rbdf->cbd_datlen = 0;
- rbdf->cbd_sc = 0xb000;
-
- iip->iic_tbase = IIC_BD_TX1;
- iip->iic_tbptr = IIC_BD_TX1;
- iip->iic_rbase = IIC_BD_RX;
- iip->iic_rbptr = IIC_BD_RX;
- iip->iic_rfcr = 0x15;
- iip->iic_tfcr = 0x15;
- iip->iic_mrblr = count;
- iip->iic_rstate = 0;
- iip->iic_tstate = 0;
-
- i2c->i2c_i2cer = 0x1f; /* clear event mask */
- i2c->i2c_i2mod |= 1; /* enable iic operation */
- i2c->i2c_i2com |= 0x80; /* start master */
-
- /* wait for IIC transfer */
- do {
- __asm__ volatile ("eieio");
- event = i2c->i2c_i2cer;
- } while (event == 0);
-
- if ((event & 0x10) || (event & 0x04)) {
- count = -1;
- goto bailout;
- }
-
-bailout:
- i2c->i2c_i2mod &= ~1; /* turn off iic operation */
- i2c->i2c_i2cer = 0x1f; /* clear event mask */
-
- return count;
-}
diff --git a/board/mbx8xx/vpd.h b/board/mbx8xx/vpd.h
deleted file mode 100644
index 1d9eb7fe20..0000000000
--- a/board/mbx8xx/vpd.h
+++ /dev/null
@@ -1,119 +0,0 @@
-#ifndef __vpd_h
-#define __vpd_h
-
-/*
- * Module name: %M%
- * Description:
- * Vital Product Data (VPD) Header Module
- * SCCS identification: %I%
- * Branch: %B%
- * Sequence: %S%
- * Date newest applied delta was created (MM/DD/YY): %G%
- * Time newest applied delta was created (HH:MM:SS): %U%
- * SCCS file name %F%
- * Fully qualified SCCS file name:
- * %P%
- * Copyright:
- * (C) COPYRIGHT MOTOROLA, INC. 1996
- * ALL RIGHTS RESERVED
- * Notes:
- * History:
- * Date Who
- *
- * 10/24/96 Rob Baxter
- * Initial release.
- *
- */
-
-#define VPD_EEPROM_SIZE 256 /* EEPROM size in bytes */
-
-/*
- * packet tuple identifiers
- *
- * 0x0D - 0xBF reserved
- * 0xC0 - 0xFE user defined
- */
-#define VPD_PID_GI 0x00 /* guaranteed illegal */
-#define VPD_PID_PID 0x01 /* product identifier (ASCII) */
-#define VPD_PID_FAN 0x02 /* factory assembly-number (ASCII) */
-#define VPD_PID_SN 0x03 /* serial-number (ASCII) */
-#define VPD_PID_PCO 0x04 /* product configuration options(binary) */
-#define VPD_PID_ICS 0x05 /* internal clock speed in HZ (integer) */
-#define VPD_PID_ECS 0x06 /* external clock speed in HZ (integer) */
-#define VPD_PID_RCS 0x07 /* reference clock speed in HZ(integer) */
-#define VPD_PID_EA 0x08 /* ethernet address (binary) */
-#define VPD_PID_MT 0x09 /* microprocessor type (ASCII) */
-#define VPD_PID_CRC 0x0A /* EEPROM CRC (integer) */
-#define VPD_PID_FMC 0x0B /* FLASH memory configuration (binary) */
-#define VPD_PID_VLSI 0x0C /* VLSI revisions/versions (binary) */
-#define VPD_PID_TERM 0xFF /* termination */
-
-/*
- * VPD structure (format)
- */
-#define VPD_EYE_SIZE 8 /* eyecatcher size */
-typedef struct vpd_header
-{
- uchar eyecatcher[VPD_EYE_SIZE]; /* eyecatcher - "MOTOROLA" */
- ushort size; /* size of EEPROM */
-} vpd_header_t;
-
-#define VPD_DATA_SIZE (VPD_EEPROM_SIZE-sizeof(vpd_header_t))
-typedef struct vpd
-{
- vpd_header_t header; /* header */
- uchar packets[VPD_DATA_SIZE]; /* data */
-} vpd_t;
-
-/*
- * packet tuple structure (format)
- */
-typedef struct vpd_packet
-{
- uchar identifier; /* identifier (PIDs above) */
- uchar size; /* size of the following data area */
- uchar data[1]; /* data (size is dependent upon PID) */
-} vpd_packet_t;
-
-/*
- * MBX product configuration options bit definitions
- *
- * Notes:
- * 1. The bit numbering is reversed in perspective with the C compiler.
- */
-#define PCO_BBRAM (1<<0) /* battery-backed RAM (BBRAM) and socket */
-#define PCO_BOOTROM (1<<1) /* boot ROM and socket (i.e., socketed FLASH) */
-#define PCO_KAPWR (1<<2) /* keep alive power source (lithium battey) and control circuit */
-#define PCO_ENET_TP (1<<3) /* ethernet twisted pair (TP) connector (RJ45) */
-#define PCO_ENET_AUI (1<<4) /* ethernet attachment unit interface (AUI) header */
-#define PCO_PCMCIA (1<<5) /* PCMCIA socket */
-#define PCO_DIMM (1<<6) /* DIMM module socket */
-#define PCO_DTT (1<<7) /* digital thermometer and thermostat (DTT) device */
-#define PCO_LCD (1<<8) /* liquid crystal display (LCD) device */
-#define PCO_PCI (1<<9) /* PCI-Bus bridge device (QSpan) and ISA-Bus bridge device (Winbond) */
-#define PCO_PCIO (1<<10) /* PC I/O (COM1, COM2, FDC, LPT, Keyboard/Mouse) */
-#define PCO_EIDE (1<<11) /* enhanced IDE (EIDE) header */
-#define PCO_FDC (1<<12) /* floppy disk controller (FDC) header */
-#define PCO_LPT_8XX (1<<13) /* parallel port header via MPC8xx */
-#define PCO_LPT_PCIO (1<<14) /* parallel port header via PC I/O */
-
-/*
- * FLASH memory configuration packet data
- */
-typedef struct vpd_fmc
-{
- ushort mid; /* manufacturer's idenitfier */
- ushort did; /* manufacturer's device idenitfier */
- uchar ddw; /* device data width (e.g., 8-bits, 16-bits) */
- uchar nod; /* number of devices present */
- uchar noc; /* number of columns */
- uchar cw; /* column width in bits */
- uchar wedw; /* write/erase data width */
-} vpd_fmc_t;
-
-/* function prototypes */
-extern void vpd_init(void);
-extern int vpd_read(uint iic_device, uchar *buf, int count, int offset);
-extern vpd_packet_t *vpd_find_packet(u_char ident);
-
-#endif /* __vpd_h */
diff --git a/boards.cfg b/boards.cfg
index 26e784b01c..384f319382 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -1253,5 +1253,3 @@ Orphan powerpc mpc8xx - - fads
Orphan powerpc mpc8xx - - fads FADS850SAR - -
Orphan powerpc mpc8xx - - fads FADS860T - -
Orphan powerpc mpc8xx - - genietv GENIETV - -
-Orphan powerpc mpc8xx - - mbx8xx MBX - -
-Orphan powerpc mpc8xx - - mbx8xx MBX860T - -
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 7f519916fd..4e0ad323c7 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -11,6 +11,7 @@ easily if here is something they might want to dig for...
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+mbx8xx powerpc mpc8xx - 2014-04-04
nx823 powerpc mpc8xx - 2014-04-04
idmr m68k mcf52x2 ba650e9b 2014-01-28
M5271EVB m68k mcf52x2 ba650e9b 2014-01-28
diff --git a/include/common.h b/include/common.h
index cbd3c9e043..580615b9ef 100644
--- a/include/common.h
+++ b/include/common.h
@@ -511,13 +511,6 @@ void rpxclassic_init (void);
void rpxlite_init (void);
-#ifdef CONFIG_MBX
-/* $(BOARD)/mbx8xx.c */
-void mbx_init (void);
-void board_serial_init (void);
-void board_ether_init (void);
-#endif
-
#ifdef CONFIG_HERMES
/* $(BOARD)/hermes.c */
void hermes_start_lxt980 (int speed);
diff --git a/include/commproc.h b/include/commproc.h
index 12b9421060..62468c30aa 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -12,10 +12,6 @@
* CPM capabilities. I (or someone else) will add definitions as they
* are needed. -- Dan
*
- * On the MBX board, EPPC-Bug loads CPM microcode into the first 512
- * bytes of the DP RAM and relocates the I2C parameter area to the
- * IDMA1 space. The remaining DP RAM is available for buffer descriptors
- * or other use.
*/
#ifndef __CPM_8XX__
#define __CPM_8XX__
@@ -135,7 +131,6 @@ typedef struct cpm_buf_desc {
#define PROFF_SMC2 ((uint)0x0380)
/* Define enough so I can at least use the serial port as a UART.
- * The MBX uses SMC1 as the host serial port.
*/
typedef struct smc_uart {
ushort smc_rbase; /* Rx Buffer descriptor base address */
@@ -888,33 +883,6 @@ typedef struct scc_enet {
#define SICR_ENET_CLKRT ((uint)0x00003E00)
#endif /* CONFIG_LWMON */
-/*** MBX ************************************************************/
-
-#ifdef CONFIG_MBX
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use. The TCLK and RCLK seem unique
- * to the MBX860 board. Any two of the four available clocks could be
- * used, and the MPC860 cookbook manual has an example using different
- * clock pins.
- */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define PA_ENET_RXD ((ushort)0x0001)
-#define PA_ENET_TXD ((ushort)0x0002)
-#define PA_ENET_TCLK ((ushort)0x0200)
-#define PA_ENET_RCLK ((ushort)0x0800)
-#define PC_ENET_TENA ((ushort)0x0001)
-#define PC_ENET_CLSN ((ushort)0x0010)
-#define PC_ENET_RENA ((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000003d)
-#endif /* CONFIG_MBX */
-
/*** KM8XX *********************************************************/
/* The KM8XX Service Module uses SCC3 for Ethernet */
diff --git a/include/configs/MBX.h b/include/configs/MBX.h
deleted file mode 100644
index 96edd442d0..0000000000
--- a/include/configs/MBX.h
+++ /dev/null
@@ -1,290 +0,0 @@
-/*
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * Configuation settings for the MBX8xx board.
- *
- * -----------------------------------------------------------------
- * SPDX-License-Identifier: GPL-2.0+
- */
-/*
- * Changed 2002-10-01
- * Added PCMCIA defines mostly taken from other U-Boot boards that
- * have PCMCIA already working. If you find any bugs, incorrect assumptions
- * feel free to fix them yourself and submit a patch.
- * Rod Boyce <rod_boyce@stratexnet.com.
- */
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860 1 /* This is a MPC860 CPU */
-#define CONFIG_MBX 1 /* ...on an MBX module */
-
-#define CONFIG_SYS_TEXT_BASE 0xfe000000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#undef CONFIG_8xx_CONS_SMC2
-#undef CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE 9600
-/* Define this to use the PCI bus */
-#undef CONFIG_USE_PCI
-
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-#define CONFIG_8xx_GCLK_FREQ (50000000UL)
-#if 1
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-#define CONFIG_BOOTCOMMAND "bootm 20000" /* autoboot command */
-
-#define CONFIG_BOOTARGS "root=/dev/nfs rw " \
- "nfsroot=10.0.0.2:/opt/eldk/ppc_8xx " \
- "nfsaddrs=10.0.0.99:10.0.0.2"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_PCMCIA
-#define CONFIG_CMD_IDE
-
-
-#define CONFIG_DOS_PARTITION
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#undef CONFIG_SYS_HUSH_PARSER /* Hush parse for U-Boot */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-/*-----------------------------------------------------------------------
- * Physical memory map as defined by the MBX PGM
- */
-#define CONFIG_SYS_IMMR 0xFA200000 /* Internal Memory Mapped Register*/
-#define CONFIG_SYS_NVRAM_BASE 0xFA000000 /* NVRAM */
-#define CONFIG_SYS_NVRAM_OR 0xffe00000 /* w/o speed dependent flags!! */
-#define CONFIG_SYS_CSR_BASE 0xFA100000 /* Control/Status Registers */
-#define CONFIG_SYS_PCIMEM_BASE 0x80000000 /* PCI I/O and Memory Spaces */
-#define CONFIG_SYS_PCIMEM_OR 0xA0000108
-#define CONFIG_SYS_PCIBRIDGE_BASE 0xFA210000 /* PCI-Bus Bridge Registers */
-#define CONFIG_SYS_PCIBRIDGE_OR 0xFFFF0108
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2f00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_VPD_SIZE 256 /* size in bytes reserved for vpd buffer */
-#define CONFIG_SYS_INIT_VPD_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_VPD_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_VPD_OFFSET-8)
-
-/*-----------------------------------------------------------------------
- * Offset in DPMEM where we keep the VPD data
- */
-#define CONFIG_SYS_DPRAMVPD (CONFIG_SYS_INIT_VPD_OFFSET - 0x2000)
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xfe000000
-#ifdef DEBUG
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#else
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#endif
-#undef CONFIG_SYS_MONITOR_BASE /* 0x200000 to run U-Boot from RAM */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 16 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-/*-----------------------------------------------------------------------
- * NVRAM Configuration
- *
- * Note: the MBX is special because there is already a firmware on this
- * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we
- * access the NVRAM at the offset 0x1000.
- */
-#define CONFIG_ENV_IS_IN_NVRAM 1 /* turn on NVRAM env feature */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_NVRAM_BASE + 0x1000)
-#define CONFIG_ENV_SIZE 0x1000
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-/* #define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME) */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC11 | SIUMCR_SEME | SIUMCR_BSC )
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit - leave PLL multiplication factor unchanged !
- */
-#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK (SCCR_RTDIV | SCCR_RTSEL)
-#define CONFIG_SYS_SCCR SCCR_TBS
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-#define CONFIG_SYS_PCMCIA_INTERRUPT SIU_LEVEL6
-
-#define CONFIG_PCMCIA_SLOT_A 1
-
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-/*-----------------------------------------------------------------------
- * Debug Entry Mode
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/MBX860T.h b/include/configs/MBX860T.h
deleted file mode 100644
index 74f44df682..0000000000
--- a/include/configs/MBX860T.h
+++ /dev/null
@@ -1,395 +0,0 @@
- /*
- * A collection of structures, addresses, and values associated with
- * the Motorola 860T MBX board.
- * Copied from the FADS stuff, which was originally copied from the MBX stuff!
- * Magnus Damm added defines for 8xxrom and extended bd_info.
- * Helmut Buchsbaum added bitvalues for BCSRx
- * Rob Taylor coverted it back to MBX
- *
- * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#include <mpc8xx_irq.h>
-
-#define CONFIG_MPC860 1
-#define CONFIG_MPC860T 1
-#define CONFIG_MBX 1
-
-#define CONFIG_SYS_TEXT_BASE 0xfe000000
-
-#define CONFIG_8xx_CPUCLOCK 40
-#define CONFIG_8xx_BUSCLOCK (CONFIG_8xx_CPUCLOCK)
-#define TARGET_SYSTEM_FREQUENCY 40
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#undef CONFIG_8xx_CONS_SMC2
-#define CONFIG_BAUDRATE 9600
-
-#define MPC8XX_FACT 10 /* Multiply by 10 */
-#define MPC8XX_XIN 40000000 /* 50 MHz in */
-#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
-
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-
-#if 1
-#define CONFIG_8xx_BOOTDELAY -1 /* autoboot disabled */
-#define CONFIG_8xx_TFTP_MODE
-#else
-#define CONFIG_8xx_BOOTDELAY 5 /* autoboot after 5 seconds */
-#undef CONFIG_8xx_TFTP_MODE
-#endif
-
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_DRAM_SPEED (CONFIG_8xx_BUSCLOCK) /* MHz */
-#define CONFIG_BOOTCOMMAND "bootm FE020000" /* autoboot command */
-#define CONFIG_BOOTARGS " "
-/*
- * Miscellaneous configurable options
- */
-#undef CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT ":>" /* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0800000 /* 4 ... 8 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFA00000
-#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024))
-#define CONFIG_SYS_NVRAM_BASE 0xFA000000 /* NVRAM */
-#define CONFIG_SYS_NVRAM_OR 0xffe00000 /* w/o speed dependent flags!! */
-#define CONFIG_SYS_CSR_BASE 0xFA100000 /* Control/Status Registers */
-#define CONFIG_SYS_PCIMEM_BASE 0x80000000 /* PCI I/O and Memory Spaces */
-#define CONFIG_SYS_PCIMEM_OR 0xA0000108
-#define CONFIG_SYS_PCIBRIDGE_BASE 0xFA210000 /* PCI-Bus Bridge Registers */
-#define CONFIG_SYS_PCIBRIDGE_OR 0xFFFF0108
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2f00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_VPD_SIZE 256 /* size in bytes reserved for vpd buffer */
-#define CONFIG_SYS_INIT_VPD_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_VPD_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_VPD_OFFSET-8)
-
-/*-----------------------------------------------------------------------
- * Offset in DPMEM where we keep the VPD data
- */
-#define CONFIG_SYS_DPRAMVPD (CONFIG_SYS_INIT_VPD_OFFSET - 0x2000)
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x00000000
-/*0xFE000000*/
-#define CONFIG_SYS_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_HWINFO_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_SYS_HWINFO_LEN)
-#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 4 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 16 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-/*-----------------------------------------------------------------------
- * NVRAM Configuration
- *
- * Note: the MBX is special because there is already a firmware on this
- * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we
- * access the NVRAM at the offset 0x1000.
- */
-#define CONFIG_ENV_IS_IN_NVRAM 1 /* turn on NVRAM env feature */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_NVRAM_BASE + 0x1000)
-#define CONFIG_ENV_SIZE 0x1000
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit - leave PLL multiplication factor unchanged !
- */
-#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK (SCCR_RTDIV | SCCR_RTSEL)
-#define CONFIG_SYS_SCCR SCCR_TBS
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently. Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register. For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-
-#define BCSR_ADDR ((uint) 0xFF010000)
-#define BCSR_SIZE ((uint)(64 * 1024))
-
-#define FLASH_BASE0_PRELIM 0xFE000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0xFF010000 /* FLASH bank #0 */
-
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xFFF00000 /* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (0xFF800000 | OR_CSNT_SAM | OR_BI | OR_SCY_3_CLK) /* 1 Mbyte until detected and only 1 Mbyte is needed*/
-#define CONFIG_SYS_BR0_PRELIM (0xFE000000 | BR_V )
-
-/* BCSRx - Board Control and Status Registers */
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM 0xFFC00000 | OR_ACS_DIV4
-#define CONFIG_SYS_BR1_PRELIM (0x00000000 | BR_MS_UPMA | BR_V )
-
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-#define CONFIG_SYS_MAMR 0x13821000
-
-/* values according to the manual */
-
-
-#define PCMCIA_MEM_ADDR ((uint)0xff020000)
-#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
-
-#define BCSR0 ((uint) (BCSR_ADDR + 00))
-#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
-#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
-#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
-#define BCSR4 ((uint) (BCSR_ADDR + 0x10))
-
-/* FADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB ((uint)0x80000000)
-#define BCSR0_IP ((uint)0x40000000)
-#define BCSR0_BDIS ((uint)0x10000000)
-#define BCSR0_BPS_MASK ((uint)0x0C000000)
-#define BCSR0_ISB_MASK ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN ((uint)0x80000000)
-#define BCSR1_DRAM_EN ((uint)0x40000000)
-#define BCSR1_ETHEN ((uint)0x20000000)
-#define BCSR1_IRDEN ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN ((uint)0x02000000)
-#define BCSR1_RS232EN_1 ((uint)0x01000000)
-#define BCSR1_PCCEN ((uint)0x00800000)
-#define BCSR1_PCCVCC0 ((uint)0x00400000)
-#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
-#define BCSR1_RS232EN_2 ((uint)0x00040000)
-#define BCSR1_SDRAM_EN ((uint)0x00020000)
-#define BCSR1_PCCVCC1 ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
-#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT (23)
-#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0 ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
-#define BCSR3_BREVN1 ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK ((ushort)0x0003)
-
-#define BCSR4_ETHLOOP ((uint)0x80000000)
-#define BCSR4_TFPLDL ((uint)0x40000000)
-#define BCSR4_TPSQEL ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860SAR
-#define BCSR4_UTOPIA_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC860SAR */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETH_EN ((uint)0x08000000)
-#endif /* CONFIG_MPC860T */
-#define BCSR4_USB_SPEED ((uint)0x04000000)
-#define BCSR4_VCCO ((uint)0x02000000)
-#define BCSR4_VIDEO_ON ((uint)0x00800000)
-#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000)
-#define BCSR4_VIDEO_RST ((uint)0x00200000)
-#define BCSR4_MODEM_EN ((uint)0x00100000)
-#define BCSR4_DATA_VOICE ((uint)0x00080000)
-
-#define CONFIG_DRAM_40MHZ 1
-
-#ifdef CONFIG_MPC860T
-
-/* Interrupt level assignments.
-*/
-#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */
-
-#endif /* CONFIG_MPC860T */
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS 0
-
-#define CONFIG_CMD_NET
-/*
- * MPC8xx CPM Options
- */
-#define CONFIG_SCC_ENET 1
-#define CONFIG_SCC1_ENET 1
-#define CONFIG_FEC_ENET 1
-#undef CONFIG_CPM_IIC
-#undef CONFIG_UCODE_PATCH
-
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-
-/* PCMCIA configuration */
-
-#define PCMCIA_MAX_SLOTS 2
-
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
-
-#endif /* __CONFIG_H */
diff --git a/post/cpu/mpc8xx/ether.c b/post/cpu/mpc8xx/ether.c
index 91505475e8..53c0e4dfda 100644
--- a/post/cpu/mpc8xx/ether.c
+++ b/post/cpu/mpc8xx/ether.c
@@ -374,10 +374,6 @@ static void scc_init (int scc_index)
*((uchar *) BCSR0) |= BCSR0_ETHEN;
#endif
-#ifdef CONFIG_MBX
- board_ether_init ();
-#endif
-
/*
* Set the ENT/ENR bits in the GSMR Low -- Enable Transmit/Receive
*/
diff --git a/post/cpu/mpc8xx/uart.c b/post/cpu/mpc8xx/uart.c
index 106a9b87d2..25d63d8120 100644
--- a/post/cpu/mpc8xx/uart.c
+++ b/post/cpu/mpc8xx/uart.c
@@ -141,10 +141,6 @@ static void smc_init (int smc_index)
up->smc_rfcr = SMC_EB;
up->smc_tfcr = SMC_EB;
-#if defined(CONFIG_MBX)
- board_serial_init ();
-#endif
-
/* Set UART mode, 8 bit, no parity, one stop.
* Enable receive and transmit.
* Set local loopback mode.