Merge branch 'master' of git://git.denx.de/u-boot-arm

16 files changed, 59 insertions, 163 deletions

diff --git a/include/asm-arm/arch-omap3/omap3.h b/include/asm-arm/arch-omap3/omap3.h
index 8c9656f9e1..7c1101969c 100644
--- a/include/asm-arm/arch-omap3/omap3.h
+++ b/include/asm-arm/arch-omap3/omap3.h
@@ -167,24 +167,20 @@ typedef struct gpio {
  * 343x real hardware:
  *  ES1     = rev 0
  *
- * 343x code defines:
- * ES1     = 0+1 = 1
- * ES1     = 1+1 = 1
+ *  ES2 onwards, the value maps to contents of IDCODE register [31:28].
  */
-#define CPU_3430_ES1		1
-#define CPU_3430_ES2		2
+#define CPU_3XX_ES10		0
+#define CPU_3XX_ES20		1
+#define CPU_3XX_ES21		2
+#define CPU_3XX_ES30		3
+#define CPU_3XX_ES31		4
+#define CPU_3XX_MAX_REV		(CPU_3XX_ES31 + 1)
+
+#define CPU_3XX_ID_SHIFT	28
 
 #define WIDTH_8BIT		0x0000
 #define WIDTH_16BIT		0x1000	/* bit pos for 16 bit in gpmc */
 
-/* SDP definitions according to FPGA Rev. Is this OK?? */
-#define SDP_3430_V1		0x1
-#define SDP_3430_V2		0x2
-
-/* EVM definitions */
-#define OMAP3EVM_V1		0x1
-#define OMAP3EVM_V2		0x2
-
 /* I2C power management companion definitions */
 #define PWRMGT_ADDR_ID1		0x48
 #define PWRMGT_ADDR_ID2		0x49
diff --git a/include/asm-arm/arch-omap3/sys_proto.h b/include/asm-arm/arch-omap3/sys_proto.h
index 8b554bbe8e..7361d08961 100644
--- a/include/asm-arm/arch-omap3/sys_proto.h
+++ b/include/asm-arm/arch-omap3/sys_proto.h
@@ -22,8 +22,6 @@
 #define _SYS_PROTO_H_
 
 typedef struct {
-	u32 board_type_v1;
-	u32 board_type_v2;
 	u32 mtype;
 	char *board_string;
 	char *nand_string;
@@ -46,8 +44,6 @@ u32 get_sysboot_value(void);
 u32 is_gpmc_muxed(void);
 u32 get_gpmc0_type(void);
 u32 get_gpmc0_width(void);
-u32 get_board_type(void);
-void display_board_info(u32);
 u32 get_sdr_cs_size(u32);
 u32 get_sdr_cs_offset(u32);
 u32 is_running_in_sdram(void);
diff --git a/include/configs/SX1.h b/include/configs/SX1.h
index caa6592f7a..61492766f6 100644
--- a/include/configs/SX1.h
+++ b/include/configs/SX1.h
@@ -135,12 +135,12 @@
 
 #define CONFIG_SYS_LOAD_ADDR		0x10000000	/* default load address */
 
-/* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1.
+/* The 1510 has 3 timers, they can be driven by the RefClk (12MHz) or by DPLL1.
  * This time is further subdivided by a local divisor.
  */
 #define CONFIG_SYS_TIMERBASE	OMAP1510_TIMER1_BASE	/* use timer 1 */
-#define CONFIG_SYS_PTV		7	/* 2^(PTV+1), divide by 256 */
-#define CONFIG_SYS_HZ		((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
+#define CONFIG_SYS_PTV		2	/* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ		1000
 
 /*-----------------------------------------------------------------------
  * Stack sizes
diff --git a/include/configs/davinci_dvevm.h b/include/configs/davinci_dvevm.h
index fae430ba6f..9fe4072b4b 100644
--- a/include/configs/davinci_dvevm.h
+++ b/include/configs/davinci_dvevm.h
@@ -56,7 +56,6 @@
 /* SoC Configuration */
 /*===================*/
 #define CONFIG_ARM926EJS			/* arm926ejs CPU core */
-#define CONFIG_SYS_CLK_FREQ	297000000	/* Arm Clock frequency */
 #define CONFIG_SYS_TIMERBASE		0x01c21400	/* use timer 0 */
 #define CONFIG_SYS_HZ_CLOCK		27000000	/* Timer Input clock freq */
 #define CONFIG_SYS_HZ			1000
@@ -87,7 +86,7 @@
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	-4	/* NS16550 register size, byteorder */
 #define CONFIG_SYS_NS16550_COM1	0x01c20000	/* Base address of UART0 */
-#define CONFIG_SYS_NS16550_CLK		27000000	/* Input clock to NS16550 */
+#define CONFIG_SYS_NS16550_CLK	CONFIG_SYS_HZ_CLOCK	/* Input clock to NS16550 */
 #define CONFIG_CONS_INDEX	1		/* use UART0 for console */
 #define CONFIG_BAUDRATE		115200		/* Default baud rate */
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
diff --git a/include/configs/davinci_schmoogie.h b/include/configs/davinci_schmoogie.h
index 923e4777be..a16ac391b3 100644
--- a/include/configs/davinci_schmoogie.h
+++ b/include/configs/davinci_schmoogie.h
@@ -31,7 +31,6 @@
 /* SoC Configuration */
 /*===================*/
 #define CONFIG_ARM926EJS			/* arm926ejs CPU core */
-#define CONFIG_SYS_CLK_FREQ	297000000	/* Arm Clock frequency */
 #define CONFIG_SYS_TIMERBASE		0x01c21400	/* use timer 0 */
 #define CONFIG_SYS_HZ_CLOCK		27000000	/* Timer Input clock freq */
 #define CONFIG_SYS_HZ			1000
@@ -54,7 +53,7 @@
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	-4	/* NS16550 register size, byteorder */
 #define CONFIG_SYS_NS16550_COM1	0x01c20000	/* Base address of UART0 */
-#define CONFIG_SYS_NS16550_CLK		27000000	/* Input clock to NS16550 */
+#define CONFIG_SYS_NS16550_CLK	CONFIG_SYS_HZ_CLOCK	/* Input clock to NS16550 */
 #define CONFIG_CONS_INDEX	1		/* use UART0 for console */
 #define CONFIG_BAUDRATE		115200		/* Default baud rate */
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
diff --git a/include/configs/davinci_sffsdr.h b/include/configs/davinci_sffsdr.h
index 73a59db871..c2ebd97dba 100644
--- a/include/configs/davinci_sffsdr.h
+++ b/include/configs/davinci_sffsdr.h
@@ -32,7 +32,6 @@
 				 * powering ON the DSP. */
 /* SoC Configuration */
 #define CONFIG_ARM926EJS			/* arm926ejs CPU core */
-#define CONFIG_SYS_CLK_FREQ	297000000	/* Arm Clock frequency */
 #define CONFIG_SYS_TIMERBASE		0x01c21400	/* use timer 0 */
 #define CONFIG_SYS_HZ_CLOCK		27000000	/* Timer Input clock freq */
 #define CONFIG_SYS_HZ			1000
@@ -56,7 +55,7 @@
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	-4	/* NS16550 register size, byteorder */
 #define CONFIG_SYS_NS16550_COM1	0x01c20000	/* Base address of UART0 */
-#define CONFIG_SYS_NS16550_CLK		27000000	/* Input clock to NS16550 */
+#define CONFIG_SYS_NS16550_CLK	CONFIG_SYS_HZ_CLOCK	/* Input clock to NS16550 */
 #define CONFIG_CONS_INDEX	1		/* use UART0 for console */
 #define CONFIG_BAUDRATE		115200		/* Default baud rate */
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
diff --git a/include/configs/davinci_sonata.h b/include/configs/davinci_sonata.h
index 70d2c7d0c5..0fc6012bac 100644
--- a/include/configs/davinci_sonata.h
+++ b/include/configs/davinci_sonata.h
@@ -56,7 +56,6 @@
 /* SoC Configuration */
 /*===================*/
 #define CONFIG_ARM926EJS			/* arm926ejs CPU core */
-#define CONFIG_SYS_CLK_FREQ	297000000	/* Arm Clock frequency */
 #define CONFIG_SYS_TIMERBASE		0x01c21400	/* use timer 0 */
 #define CONFIG_SYS_HZ_CLOCK		27000000	/* Timer Input clock freq */
 #define CONFIG_SYS_HZ			1000
@@ -87,7 +86,7 @@
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	-4	/* NS16550 register size, byteorder */
 #define CONFIG_SYS_NS16550_COM1	0x01c20000	/* Base address of UART0 */
-#define CONFIG_SYS_NS16550_CLK		27000000	/* Input clock to NS16550 */
+#define CONFIG_SYS_NS16550_CLK	CONFIG_SYS_HZ_CLOCK	/* Input clock to NS16550 */
 #define CONFIG_CONS_INDEX	1		/* use UART0 for console */
 #define CONFIG_BAUDRATE		115200		/* Default baud rate */
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
diff --git a/include/configs/netstar.h b/include/configs/netstar.h
index 39560de3c5..5cfee66229 100644
--- a/include/configs/netstar.h
+++ b/include/configs/netstar.h
@@ -222,12 +222,12 @@
 
 #define CONFIG_SYS_LOAD_ADDR		PHYS_SDRAM_1 + 0x400000	/* default load address */
 
-/* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1.
+/* The 1510 has 3 timers, they can be driven by the RefClk (12MHz) or by DPLL1.
  * This time is further subdivided by a local divisor.
  */
 #define CONFIG_SYS_TIMERBASE		OMAP1510_TIMER1_BASE
-#define CONFIG_SYS_PTV			7		/* 2^(pvt+1), divide by 256 */
-#define CONFIG_SYS_HZ			((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
+#define CONFIG_SYS_PTV			7
+#define CONFIG_SYS_HZ			1000
 
 #define OMAP5910_DPLL_DIV	1
 #define OMAP5910_DPLL_MUL	((CONFIG_SYS_CLK_FREQ * \
diff --git a/include/configs/omap1510inn.h b/include/configs/omap1510inn.h
index 6c1c5ec0d7..8408209d6c 100644
--- a/include/configs/omap1510inn.h
+++ b/include/configs/omap1510inn.h
@@ -132,12 +132,12 @@
 
 #define CONFIG_SYS_LOAD_ADDR		0x10000000	/* default load address */
 
-/* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1.
+/* The 1510 has 3 timers, they can be driven by the RefClk (12MHz) or by DPLL1.
  * This time is further subdivided by a local divisor.
  */
 #define CONFIG_SYS_TIMERBASE	OMAP1510_TIMER1_BASE	/* use timer 1 */
-#define CONFIG_SYS_PTV		7	/* 2^(PTV+1), divide by 256 */
-#define CONFIG_SYS_HZ		((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
+#define CONFIG_SYS_PTV		2	/* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_HZ		1000
 
 /*-----------------------------------------------------------------------
  * Stack sizes
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 5a948e4cd6..d8c328f1b4 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -41,6 +41,12 @@
 #include <asm/arch/cpu.h>		/* get chip and board defs */
 #include <asm/arch/omap3.h>
 
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO		1
+#define CONFIG_DISPLAY_BOARDINFO	1
+
 /* Clock Defines */
 #define V_OSCK			26000000	/* Clock output from T2 */
 #define V_SCLK			(V_OSCK >> 1)
@@ -135,18 +141,6 @@
 
 #define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of NAND */
 							/* devices */
-#define SECTORSIZE			512
-
-#define NAND_ALLOW_ERASE_ALL
-#define ADDR_COLUMN			1
-#define ADDR_PAGE			2
-#define ADDR_COLUMN_PAGE		3
-
-#define NAND_ChipID_UNKNOWN		0x00
-#define NAND_MAX_FLOORS			1
-#define NAND_MAX_CHIPS			1
-#define NAND_NO_RB			1
-#define CONFIG_SYS_NAND_WP
 
 #define CONFIG_JFFS2_NAND
 /* nand device jffs2 lives on */
@@ -185,7 +179,7 @@
 		"bootm ${loadaddr}\0" \
 
 #define CONFIG_BOOTCOMMAND \
-	"if mmcinit; then " \
+	"if mmc init; then " \
 		"if run loadbootscript; then " \
 			"run bootscript; " \
 		"else " \
@@ -306,21 +300,4 @@ extern unsigned int boot_flash_sec;
 extern unsigned int boot_flash_type;
 #endif
 
-
-#define WRITE_NAND_COMMAND(d, adr)\
-			writel(d, &nand_cs_base->nand_cmd)
-#define WRITE_NAND_ADDRESS(d, adr)\
-			writel(d, &nand_cs_base->nand_adr)
-#define WRITE_NAND(d, adr) writew(d, &nand_cs_base->nand_dat)
-#define READ_NAND(adr) readl(&nand_cs_base->nand_dat)
-
-/* Other NAND Access APIs */
-#define NAND_WP_OFF() do {readl(&gpmc_cfg_base->config) |= GPMC_CONFIG_WP; } \
-			while (0)
-#define NAND_WP_ON() do {readl(&gpmc_cfg_base->config) &= ~GPMC_CONFIG_WP; } \
-			while (0)
-#define NAND_DISABLE_CE(nand)
-#define NAND_ENABLE_CE(nand)
-#define NAND_WAIT_READY(nand)	udelay(10)
-
 #endif /* __CONFIG_H */
diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h
index 8cd8a1b90f..ab014e9502 100644
--- a/include/configs/omap3_evm.h
+++ b/include/configs/omap3_evm.h
@@ -46,6 +46,12 @@
 #include <asm/arch/cpu.h>	/* get chip and board defs */
 #include <asm/arch/omap3.h>
 
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO		1
+#define CONFIG_DISPLAY_BOARDINFO	1
+
 /* Clock Defines */
 #define V_OSCK			26000000	/* Clock output from T2 */
 #define V_SCLK			(V_OSCK >> 1)
@@ -66,7 +72,6 @@
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + SZ_128K)
 #define CONFIG_SYS_GBL_DATA_SIZE	128	/* bytes reserved for */
 						/* initial data */
-
 /*
  * Hardware drivers
  */
@@ -133,18 +138,6 @@
 
 #define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of */
 							/* NAND devices */
-#define SECTORSIZE			512
-
-#define NAND_ALLOW_ERASE_ALL
-#define ADDR_COLUMN			1
-#define ADDR_PAGE			2
-#define ADDR_COLUMN_PAGE		3
-
-#define NAND_ChipID_UNKNOWN		0x00
-#define NAND_MAX_FLOORS			1
-#define NAND_MAX_CHIPS			1
-#define NAND_NO_RB			1
-#define CONFIG_SYS_NAND_WP
 
 #define CONFIG_JFFS2_NAND
 /* nand device jffs2 lives on */
@@ -178,7 +171,7 @@
 		"bootm ${loadaddr}\0" \
 
 #define CONFIG_BOOTCOMMAND \
-	"if mmcinit; then " \
+	"if mmc init; then " \
 		"if run loadbootscript; then " \
 			"run bootscript; " \
 		"else " \
@@ -299,23 +292,6 @@ extern unsigned int boot_flash_sec;
 extern unsigned int boot_flash_type;
 #endif
 
-
-#define WRITE_NAND_COMMAND(d, adr)\
-			writel(d, &nand_cs_base->nand_cmd)
-#define WRITE_NAND_ADDRESS(d, adr)\
-			writel(d, &nand_cs_base->nand_adr)
-#define WRITE_NAND(d, adr) writew(d, &nand_cs_base->nand_dat)
-#define READ_NAND(adr) readl(&nand_cs_base->nand_dat)
-
-/* Other NAND Access APIs */
-#define NAND_WP_OFF() do {readl(&gpmc_cfg_base->config) |= GPMC_CONFIG_WP; } \
-			while (0)
-#define NAND_WP_ON() do {readl(&gpmc_cfg_base->config) &= ~GPMC_CONFIG_WP; } \
-			while (0)
-#define NAND_DISABLE_CE(nand)
-#define NAND_ENABLE_CE(nand)
-#define NAND_WAIT_READY(nand)	udelay(10)
-
 /*----------------------------------------------------------------------------
  * SMSC9115 Ethernet from SMSC9118 family
  *----------------------------------------------------------------------------
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index 51b04b6428..d941497827 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -33,6 +33,12 @@
 #include <asm/arch/cpu.h>	/* get chip and board defs */
 #include <asm/arch/omap3.h>
 
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO		1
+#define CONFIG_DISPLAY_BOARDINFO	1
+
 /* Clock Defines */
 #define V_OSCK			26000000	/* Clock output from T2 */
 #define V_SCLK			(V_OSCK >> 1)
@@ -122,19 +128,6 @@
 
 #define CONFIG_SYS_MAX_NAND_DEVICE	1	/* Max number of NAND */
 						/* devices */
-#define SECTORSIZE			512
-
-#define NAND_ALLOW_ERASE_ALL
-#define ADDR_COLUMN			1
-#define ADDR_PAGE			2
-#define ADDR_COLUMN_PAGE		3
-
-#define NAND_ChipID_UNKNOWN		0x00
-#define NAND_MAX_FLOORS			1
-#define NAND_MAX_CHIPS			1
-#define NAND_NO_RB			1
-#define CONFIG_SYS_NAND_WP
-
 #define CONFIG_JFFS2_NAND
 /* nand device jffs2 lives on */
 #define CONFIG_JFFS2_DEV		"nand0"
@@ -172,7 +165,7 @@
 		"bootm ${loadaddr}\0" \
 
 #define CONFIG_BOOTCOMMAND \
-	"if mmcinit; then " \
+	"if mmc init; then " \
 		"if run loadbootscript; then " \
 			"run bootscript; " \
 		"else " \
@@ -293,21 +286,4 @@ extern unsigned int boot_flash_sec;
 extern unsigned int boot_flash_type;
 #endif
 
-
-#define WRITE_NAND_COMMAND(d, adr)\
-			writel(d, &nand_cs_base->nand_cmd)
-#define WRITE_NAND_ADDRESS(d, adr)\
-			writel(d, &nand_cs_base->nand_adr)
-#define WRITE_NAND(d, adr) writew(d, &nand_cs_base->nand_dat)
-#define READ_NAND(adr) readl(&nand_cs_base->nand_dat)
-
-/* Other NAND Access APIs */
-#define NAND_WP_OFF() do {readl(&gpmc_cfg_base->config) |= GPMC_CONFIG_WP; } \
-			while (0)
-#define NAND_WP_ON() do {readl(&gpmc_cfg_base->config) &= ~GPMC_CONFIG_WP; } \
-			while (0)
-#define NAND_DISABLE_CE(nand)
-#define NAND_ENABLE_CE(nand)
-#define NAND_WAIT_READY(nand)	udelay(10)
-
 #endif				/* __CONFIG_H */
diff --git a/include/configs/omap3_pandora.h b/include/configs/omap3_pandora.h
index 40107a60df..f9f6480df6 100644
--- a/include/configs/omap3_pandora.h
+++ b/include/configs/omap3_pandora.h
@@ -36,6 +36,12 @@
 #include <asm/arch/cpu.h>	/* get chip and board defs */
 #include <asm/arch/omap3.h>
 
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO		1
+#define CONFIG_DISPLAY_BOARDINFO	1
+
 /* Clock Defines */
 #define V_OSCK			26000000	/* Clock output from T2 */
 #define V_SCLK			(V_OSCK >> 1)
@@ -125,18 +131,6 @@
 
 #define CONFIG_SYS_MAX_NAND_DEVICE	1	/* Max number of NAND */
 						/* devices */
-#define SECTORSIZE			512
-
-#define NAND_ALLOW_ERASE_ALL
-#define ADDR_COLUMN			1
-#define ADDR_PAGE			2
-#define ADDR_COLUMN_PAGE		3
-
-#define NAND_ChipID_UNKNOWN		0x00
-#define NAND_MAX_FLOORS			1
-#define NAND_MAX_CHIPS			1
-#define NAND_NO_RB			1
-#define CONFIG_SYS_NAND_WP
 
 #define CONFIG_JFFS2_NAND
 /* nand device jffs2 lives on */
@@ -174,7 +168,7 @@
 		"bootm ${loadaddr}\0" \
 
 #define CONFIG_BOOTCOMMAND \
-	"if mmcinit; then " \
+	"if mmc init; then " \
 		"if run loadbootscript; then " \
 			"run bootscript; " \
 		"else " \
@@ -295,21 +289,4 @@ extern unsigned int boot_flash_sec;
 extern unsigned int boot_flash_type;
 #endif
 
-
-#define WRITE_NAND_COMMAND(d, adr)\
-			writel(d, &nand_cs_base->nand_cmd)
-#define WRITE_NAND_ADDRESS(d, adr)\
-			writel(d, &nand_cs_base->nand_adr)
-#define WRITE_NAND(d, adr) writew(d, &nand_cs_base->nand_dat)
-#define READ_NAND(adr) readl(&nand_cs_base->nand_dat)
-
-/* Other NAND Access APIs */
-#define NAND_WP_OFF() do {readl(&gpmc_cfg_base->config) |= GPMC_CONFIG_WP; } \
-			while (0)
-#define NAND_WP_ON() do {readl(&gpmc_cfg_base->config) &= ~GPMC_CONFIG_WP; } \
-			while (0)
-#define NAND_DISABLE_CE(nand)
-#define NAND_ENABLE_CE(nand)
-#define NAND_WAIT_READY(nand)	udelay(10)
-
 #endif				/* __CONFIG_H */
diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h
index 8e984b4161..b275b15419 100644
--- a/include/configs/omap3_zoom1.h
+++ b/include/configs/omap3_zoom1.h
@@ -42,6 +42,12 @@
 #include <asm/arch/cpu.h>		/* get chip and board defs */
 #include <asm/arch/omap3.h>
 
+/*
+ * Display CPU and Board information
+ */
+#define CONFIG_DISPLAY_CPUINFO		1
+#define CONFIG_DISPLAY_BOARDINFO	1
+
 /* Clock Defines */
 #define V_OSCK			26000000	/* Clock output from T2 */
 #define V_SCLK			(V_OSCK >> 1)
@@ -182,7 +188,7 @@
 		"bootm ${loadaddr}\0" \
 
 #define CONFIG_BOOTCOMMAND \
-	"if mmcinit; then " \
+	"if mmc init; then " \
 		"if run loadbootscript; then " \
 			"run bootscript; " \
 		"else " \
diff --git a/include/configs/voiceblue.h b/include/configs/voiceblue.h
index 3f97843722..aa8efaad5a 100644
--- a/include/configs/voiceblue.h
+++ b/include/configs/voiceblue.h
@@ -210,12 +210,12 @@
 #define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM_1
 #define CONFIG_SYS_MEMTEST_END		PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - PHYS_SDRAM_1_RESERVED
 
-/* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1.
+/* The 1510 has 3 timers, they can be driven by the RefClk (12MHz) or by DPLL1.
  * This time is further subdivided by a local divisor.
  */
 #define CONFIG_SYS_TIMERBASE	OMAP1510_TIMER1_BASE
 #define CONFIG_SYS_PTV		7	/* 2^(PTV+1), divide by 256 */
-#define CONFIG_SYS_HZ		((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV))
+#define CONFIG_SYS_HZ		1000
 
 #define OMAP5910_DPLL_DIV	1
 #define OMAP5910_DPLL_MUL	((CONFIG_SYS_CLK_FREQ * \
diff --git a/include/s3c6400.h b/include/s3c6400.h
index 87f3760b6c..e527c08b18 100644
--- a/include/s3c6400.h
+++ b/include/s3c6400.h
@@ -31,10 +31,6 @@
 #ifndef __S3C6400_H__
 #define __S3C6400_H__
 
-#ifndef CONFIG_S3C6400
-#define CONFIG_S3C6400		1
-#endif
-
 #define S3C64XX_UART_CHANNELS	3
 #define S3C64XX_SPI_CHANNELS	2