at91: reworked support for meesc board

The meesc board support was broken. Within this opportunity, I completely
reworked the board files.

Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Signed-off-by: Matthias Fuchs <Matthias.Fuchs@esd.eu>

3 files changed, 144 insertions, 108 deletions

diff --git a/board/esd/meesc/config.mk b/board/esd/meesc/config.mk
deleted file mode 100644
index 207769233e..0000000000
--- a/board/esd/meesc/config.mk
+++ /dev/null
@@ -1 +0,0 @@
-CONFIG_SYS_TEXT_BASE = 0x21f00000
diff --git a/board/esd/meesc/meesc.c b/board/esd/meesc/meesc.c
index 41fa3e1567..ad43531cb1 100644
--- a/board/esd/meesc/meesc.c
+++ b/board/esd/meesc/meesc.c
@@ -3,7 +3,7 @@
  * Stelian Pop <stelian.pop@leadtechdesign.com>
  * Lead Tech Design <www.leadtechdesign.com>
  *
- * (C) Copyright 2009-2010
+ * (C) Copyright 2009-2011
  * Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
  * esd electronic system design gmbh <www.esd.eu>
  *
@@ -27,7 +27,7 @@
  */
 
 #include <common.h>
-#include <asm/arch/at91sam9263.h>
+#include <asm/io.h>
 #include <asm/arch/at91sam9_smc.h>
 #include <asm/arch/at91_common.h>
 #include <asm/arch/at91_pmc.h>
@@ -35,8 +35,6 @@
 #include <asm/arch/at91_matrix.h>
 #include <asm/arch/at91_pio.h>
 #include <asm/arch/clk.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/io.h>
 #include <netdev.h>
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -67,8 +65,8 @@ int get_hw_rev(void)
 static void meesc_nand_hw_init(void)
 {
 	unsigned long csa;
-	at91_smc_t 	*smc 	= (at91_smc_t *) AT91_SMC0_BASE;
-	at91_matrix_t 	*matrix = (at91_matrix_t *) AT91_MATRIX_BASE;
+	at91_smc_t	*smc	= (at91_smc_t *) ATMEL_BASE_SMC0;
+	at91_matrix_t	*matrix = (at91_matrix_t *) ATMEL_BASE_MATRIX;
 
 	/* Enable CS3 */
 	csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A;
@@ -88,7 +86,7 @@ static void meesc_nand_hw_init(void)
 	writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
 		AT91_SMC_MODE_EXNW_DISABLE |
 		AT91_SMC_MODE_DBW_8 |
-		AT91_SMC_MODE_TDF_CYCLE(2),
+		AT91_SMC_MODE_TDF_CYCLE(3),
 		&smc->cs[3].mode);
 
 	/* Configure RDY/BSY */
@@ -102,9 +100,9 @@ static void meesc_nand_hw_init(void)
 #ifdef CONFIG_MACB
 static void meesc_macb_hw_init(void)
 {
-	at91_pmc_t	*pmc	= (at91_pmc_t *) AT91_PMC_BASE;
+	at91_pmc_t	*pmc	= (at91_pmc_t *) ATMEL_BASE_PMC;
 	/* Enable clock */
-	writel(1 << AT91SAM9263_ID_EMAC, &pmc->pcer);
+	writel(1 << ATMEL_ID_EMAC, &pmc->pcer);
 	at91_macb_hw_init();
 }
 #endif
@@ -117,7 +115,7 @@ static void meesc_macb_hw_init(void)
  */
 static void meesc_ethercat_hw_init(void)
 {
-	at91_smc_t 	*smc1 	= (at91_smc_t *) AT91_SMC1_BASE;
+	at91_smc_t	*smc1	= (at91_smc_t *) ATMEL_BASE_SMC1;
 
 	/* Configure SMC EBI1_CS0 for EtherCAT */
 	writel(AT91_SMC_SETUP_NWE(0) | AT91_SMC_SETUP_NCS_WR(0) |
@@ -142,8 +140,9 @@ static void meesc_ethercat_hw_init(void)
 
 int dram_init(void)
 {
-	gd->bd->bi_dram[0].start = PHYS_SDRAM;
-	gd->bd->bi_dram[0].size = get_ram_size((long *) PHYS_SDRAM, (1 << 27));
+	gd->ram_size = get_ram_size(
+		(void *)CONFIG_SYS_SDRAM_BASE,
+		CONFIG_SYS_SDRAM_SIZE);
 	return 0;
 }
 
@@ -151,7 +150,7 @@ int board_eth_init(bd_t *bis)
 {
 	int rc = 0;
 #ifdef CONFIG_MACB
-	rc = macb_eth_initialize(0, (void *)AT91_EMAC_BASE, 0x00);
+	rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
 #endif
 	return rc;
 }
@@ -225,7 +224,7 @@ int misc_init_r(void)
 {
 	char		*str;
 	char		buf[32];
-	at91_pmc_t	*pmc = (at91_pmc_t *) AT91_PMC_BASE;
+	at91_pmc_t	*pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
 
 	/*
 	 * Normally the processor clock has a divisor of 2.
@@ -246,24 +245,28 @@ int misc_init_r(void)
 }
 #endif /* CONFIG_MISC_INIT_R */
 
-int board_init(void)
+int board_early_init_f(void)
 {
-	at91_pmc_t	*pmc	= (at91_pmc_t *) AT91_PMC_BASE;
+	at91_pmc_t	*pmc	= (at91_pmc_t *) ATMEL_BASE_PMC;
 
-	/* Peripheral Clock Enable Register */
-	writel(1 << AT91SAM9263_ID_PIOA |
-		1 << AT91SAM9263_ID_PIOB |
-		1 << AT91SAM9263_ID_PIOCDE |
-		1 << AT91SAM9263_ID_UHP,
+	/* enable all clocks */
+	writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) |
+		(1 << ATMEL_ID_PIOCDE) | (1 << ATMEL_ID_UHP),
 		&pmc->pcer);
 
+	at91_seriald_hw_init();
+
+	return 0;
+}
+
+int board_init(void)
+{
 	/* initialize ET1100 Controller */
 	meesc_ethercat_hw_init();
 
 	/* adress of boot parameters */
-	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 
-	at91_serial_hw_init();
 #ifdef CONFIG_CMD_NAND
 	meesc_nand_hw_init();
 #endif
diff --git a/include/configs/meesc.h b/include/configs/meesc.h
index a27b36b378..e100cb41ce 100644
--- a/include/configs/meesc.h
+++ b/include/configs/meesc.h
@@ -3,7 +3,7 @@
  * Stelian Pop <stelian.pop@leadtechdesign.com>
  * Lead Tech Design <www.leadtechdesign.com>
  *
- * (C) Copyright 2009-2010
+ * (C) Copyright 2009-2011
  * Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
  * esd electronic system design gmbh <www.esd.eu>
  *
@@ -31,49 +31,68 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-/* Common stuff */
-#define CONFIG_MEESC			1	/* Board is esd MEESC */
-#define CONFIG_ARM926EJS		1	/* This is an ARM926EJS Core */
-#define CONFIG_AT91SAM9263		1	/* It's an AT91SAM9263 SoC */
+/*
+ * SoC must be defined first, before hardware.h is included.
+ * In this case SoC is defined in boards.cfg.
+ */
+#include <asm/hardware.h>
+
+/*
+ * Warning: changing CONFIG_SYS_TEXT_BASE requires
+ * adapting the initial boot program.
+ * Since the linker has to swallow that define, we must use a pure
+ * hex number here!
+ */
+#define CONFIG_SYS_TEXT_BASE		0x20002000
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_SLOW_CLOCK	32768	/* 32.768 kHz crystal */
 #define CONFIG_SYS_AT91_MAIN_CLOCK	16000000/* 16.0 MHz crystal */
 #define CONFIG_SYS_HZ			1000	/* decrementer freq */
-#define CONFIG_DISPLAY_BOARDINFO	1
-#define CONFIG_DISPLAY_CPUINFO		1	/* display cpu info and speed */
-#define CONFIG_PREBOOT				/* enable preboot variable */
-#define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS	1
-#define CONFIG_INITRD_TAG		1
-#define CONFIG_SERIAL_TAG		1
-#define CONFIG_REVISION_TAG		1
-#undef CONFIG_USE_IRQ				/* don't need IRQ/FIQ stuff */
 
+/* Misc CPU related */
 #define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_BOARD_EARLY_INIT_F		/* call board_early_init_f() */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_SERIAL_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_CMDLINE_TAG			/* enable passing of ATAGs */
 #define CONFIG_MISC_INIT_R			/* Call misc_init_r */
+#undef CONFIG_USE_IRQ				/* don't need IRQ/FIQ stuff */
 
-#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_DISPLAY_BOARDINFO		/* call checkboard() */
+#define CONFIG_DISPLAY_CPUINFO			/* display cpu info and speed */
+#define CONFIG_PREBOOT				/* enable preboot variable */
 
 /*
  * Hardware drivers
  */
 
+/* required until arch/arm/include/asm/arch-at91/at91sam9263.h is reworked */
+#define ATMEL_PMC_UHP			AT91SAM926x_PMC_UHP
+
+/* general purpose I/O */
+#define CONFIG_AT91_GPIO
+
 /* Console output */
-#define CONFIG_AT91_GPIO			1
-#define CONFIG_ATMEL_USART			1
-#undef CONFIG_USART0
-#undef CONFIG_USART1
-#undef CONFIG_USART2
-#define CONFIG_USART3				1	/* USART 3 is DBGU */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE		ATMEL_BASE_DBGU
+#define CONFIG_USART_ID			ATMEL_ID_SYS
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{115200, 19200, 38400, 57600, 9600}
 
-#define CONFIG_BOOTDELAY			3
-#define CONFIG_ZERO_BOOTDELAY_CHECK		1
+#define CONFIG_BOOTDELAY		3
+#define CONFIG_ZERO_BOOTDELAY_CHECK
 
 /*
  * BOOTP options
  */
-#define CONFIG_BOOTP_BOOTFILESIZE		1
-#define CONFIG_BOOTP_BOOTPATH			1
-#define CONFIG_BOOTP_GATEWAY			1
-#define CONFIG_BOOTP_HOSTNAME			1
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
 
 /*
  * Command line configuration.
@@ -84,97 +103,112 @@
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_IMLS
 
-#define CONFIG_CMD_PING				1
-#define CONFIG_CMD_DHCP				1
-#define CONFIG_CMD_NAND				1
-#define CONFIG_CMD_USB				1
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_USB
 
 /* LED */
-#define CONFIG_AT91_LED				1
+#define CONFIG_AT91_LED
 
-/* SDRAM */
-#define CONFIG_NR_DRAM_BANKS			1
-#define PHYS_SDRAM				0x20000000
+/*
+ * SDRAM: 1 bank, min 32, max 128 MB
+ * Initialized before u-boot gets started.
+ */
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_SYS_SDRAM_BASE		0x20000000 /* ATMEL_BASE_CS1 */
+#define CONFIG_SYS_SDRAM_SIZE		0x02000000
+
+#define CONFIG_SYS_MEMTEST_START	(CONFIG_SYS_SDRAM_BASE + 0x00100000)
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x01E00000)
+#define CONFIG_SYS_LOAD_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x00100000)
+
+/*
+ * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM,
+ * leaving the correct space for initial global data structure above
+ * that address while providing maximum stack area below.
+ */
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(ATMEL_BASE_SRAM0 + 0x1000 - GENERATED_GBL_DATA_SIZE)
 
 /* DataFlash */
-#define CONFIG_ATMEL_DATAFLASH_SPI
-#define CONFIG_HAS_DATAFLASH			1
-#define CONFIG_SYS_SPI_WRITE_TOUT		(5 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_MAX_DATAFLASH_BANKS		1
-#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0	0xC0000000	/* CS0 */
-#define AT91_SPI_CLK				15000000
-#define DATAFLASH_TCSS				(0x1a << 16)
-#define DATAFLASH_TCHS				(0x1 << 24)
+#ifdef CONFIG_SYS_USE_DATAFLASH
+# define CONFIG_ATMEL_DATAFLASH_SPI
+# define CONFIG_HAS_DATAFLASH
+# define CONFIG_SYS_SPI_WRITE_TOUT		(5 * CONFIG_SYS_HZ)
+# define CONFIG_SYS_MAX_DATAFLASH_BANKS		1
+# define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0	0xC0000000	/* CS0 */
+# define AT91_SPI_CLK				15000000
+# define DATAFLASH_TCSS				(0x1a << 16)
+# define DATAFLASH_TCHS				(0x1 << 24)
+#endif
 
 /* NOR flash is not populated, disable it */
-#define CONFIG_SYS_NO_FLASH			1
+#define CONFIG_SYS_NO_FLASH
 
 /* NAND flash */
 #ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_ATMEL
-#define CONFIG_SYS_MAX_NAND_DEVICE		1
-#define CONFIG_SYS_NAND_BASE			0x40000000
-#define CONFIG_SYS_NAND_DBW_8			1
-/* our ALE is AD21 */
-#define CONFIG_SYS_NAND_MASK_ALE		(1 << 21)
-/* our CLE is AD22 */
-#define CONFIG_SYS_NAND_MASK_CLE		(1 << 22)
-#define CONFIG_SYS_NAND_ENABLE_PIN		AT91_PIO_PORTD, 15
-#define CONFIG_SYS_NAND_READY_PIN		AT91_PIO_PORTA, 22
-#define CONFIG_SYS_64BIT_VSPRINTF		/* needed for nand_util.c */
+# define CONFIG_NAND_ATMEL
+# define CONFIG_SYS_MAX_NAND_DEVICE		1
+# define CONFIG_SYS_NAND_BASE			0x40000000 /* ATMEL_BASE_CS3 */
+# define CONFIG_SYS_NAND_DBW_8
+# define CONFIG_SYS_NAND_MASK_ALE		(1 << 21)
+# define CONFIG_SYS_NAND_MASK_CLE		(1 << 22)
+# define CONFIG_SYS_NAND_ENABLE_PIN		AT91_PIO_PORTD, 15
+# define CONFIG_SYS_NAND_READY_PIN		AT91_PIO_PORTA, 22
+# define CONFIG_SYS_64BIT_VSPRINTF		/* needed for nand_util.c */
 #endif
 
 /* Ethernet */
-#define CONFIG_MACB				1
-#define CONFIG_RMII				1
-#define CONFIG_NET_MULTI			1
+#define CONFIG_MACB
+#define CONFIG_RMII
+#define CONFIG_NET_MULTI
+#define CONFIG_FIT
 #define CONFIG_NET_RETRY_COUNT			20
 #undef CONFIG_RESET_PHY_R
 
 /* USB */
 #define CONFIG_USB_ATMEL
-#define CONFIG_USB_OHCI_NEW			1
-#define CONFIG_DOS_PARTITION			1
-#define CONFIG_SYS_USB_OHCI_CPU_INIT		1
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
 #define CONFIG_SYS_USB_OHCI_REGS_BASE		0x00a00000
 #define CONFIG_SYS_USB_OHCI_SLOT_NAME		"at91sam9263"
 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	2
-#define CONFIG_USB_STORAGE			1
-#define CONFIG_CMD_FAT				1
-
-#define CONFIG_SYS_LOAD_ADDR			0x22000000 /* load address */
-
-#define CONFIG_SYS_MEMTEST_START		PHYS_SDRAM
-#define CONFIG_SYS_MEMTEST_END			0x21e00000
-
-#define CONFIG_SYS_USE_DATAFLASH		1
-#undef CONFIG_SYS_USE_NANDFLASH
 
 /* CAN */
-#define CONFIG_AT91_CAN				1
+#define CONFIG_AT91_CAN
 
 /* hw-controller addresses */
-#define CONFIG_ET1100_BASE			0x70000000
+#define CONFIG_ET1100_BASE		0x70000000
+
+#ifdef CONFIG_SYS_USE_DATAFLASH
 
 /* bootstrap + u-boot + env in dataflash on CS0 */
-#define CONFIG_ENV_IS_IN_DATAFLASH	1
-#define CONFIG_SYS_MONITOR_BASE		(CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
+# define CONFIG_ENV_IS_IN_DATAFLASH
+# define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
 					0x8400)
-#define CONFIG_ENV_OFFSET		0x4200
-#define CONFIG_ENV_ADDR			(CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
+# define CONFIG_ENV_OFFSET		0x4200
+# define CONFIG_ENV_ADDR		(CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
 					CONFIG_ENV_OFFSET)
-#define CONFIG_ENV_SIZE			0x4200
+# define CONFIG_ENV_SIZE		0x4200
 
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_SYS_BAUDRATE_TABLE	{115200 , 19200, 38400, 57600, 9600 }
+#elif CONFIG_SYS_USE_NANDFLASH
+
+/* bootstrap + u-boot + env + linux in nandflash */
+# define CONFIG_ENV_IS_IN_NAND		1
+# define CONFIG_ENV_OFFSET		0xC0000
+# define CONFIG_ENV_SIZE		0x20000
+
+#endif
 
 #define CONFIG_SYS_PROMPT		"=> "
-#define CONFIG_SYS_CBSIZE		256
+#define CONFIG_SYS_CBSIZE		512
 #define CONFIG_SYS_MAXARGS		16
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP		1
-#define CONFIG_CMDLINE_EDITING		1
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
 
 /*
  * Size of malloc() pool
@@ -185,7 +219,7 @@
 #define CONFIG_STACKSIZE		(32 * 1024)	/* regular stack */
 
 #ifdef CONFIG_USE_IRQ
-#error CONFIG_USE_IRQ not supported
+# error CONFIG_USE_IRQ not supported
 #endif
 
 #endif