summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2013-05-12arm: at91: enable mci support for at91sam9g20ek.Wu, Josh
Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-05-12arm: at91: add at91sam9n12ek board supportWu, Josh
Add support for following features: - nand boot, with PMECC 2bit ECC for 512 bytes sector - SPI flash boot - SD card boot - LCD support Signed-off-by: Josh Wu <josh.wu@atmel.com> [fix -Wimplicit-function-declaration for at91_lcd_hw_init()] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-05-11Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-05-11Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: drivers/mtd/nand/mxc_nand_spl.c include/configs/m28evk.h
2013-05-11Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-05-10cm-t35: move cm-t35 to live in compulab directoryIgor Grinberg
Currently the cm-t35 support code lives under board/cm_t35 directory. Some of the code can be shared with other/future CompuLab boards, so move the cm-t35 to live under board/compulab/cm_t35 directory. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-05-10ARM:Panda:Fix device tree loading for the panda-esDan Murphy
Fix the device tree loading for panda(4430) and panda-es(4460) Modify the board name if a 4460 panda or panda-es is detected at run time. In the findfdt add a check for the panda-es board name and load the panda-es device tree blob. Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-05-10ARM: Add support for IGEP COM AQUILA/CYGNUSEnric Balletbo i Serra
The IGEP COM AQUILA and CYGNUS are industrial processors modules with following highlights: o AM3352/AM3354 Texas Instruments processor o Cortex-A8 ARM CPU o 3.3 volts Inputs / Outputs use industrial o 256 MB DDR3 SDRAM / 128 Megabytes FLASH o MicroSD card reader on-board o Ethernet controller on-board o JTAG debug connector available o Designed for industrial range purposes Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-05-10beagleboard: Update comment in get_board_rev()Tom Rini
We are able to tell the difference between xM Rev Ax/Bx and xM Rev Cx, and have been for some time. The comment above the function however did not list this, so update. Signed-off-by: Tom Rini <trini@ti.com>
2013-05-10palmas: rename init_settings to an generic palmas initNishanth Menon
Since TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs, rename twl6035_init_settings with an more generic palmas_init_settings Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10twl6035: rename to palmasNishanth Menon
TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs Rename twl6035 to palmas to allow reuse across multiple current and future platforms As part of this change, change the CONFIG_TWL6035_POWER to CONFIG_PALMAS_POWER and update usage of header file accordingly. Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10twl4030: make twl4030_i2c_read_u8 prototype consistentNishanth Menon
u-boot standard i2c read prototype is i2c_read(addr, reg, 1, &buf, 1) twl4030_i2c_read_u8(u8 addr, u8 *val, u8 reg) does not provide consistency, so switch the prototype to be consistent with rest of u-boot i2c operations: twl4030_i2c_read_u8(u8 addr, u8 reg, u8 *val) Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10twl4030: make twl4030_i2c_write_u8 prototype consistentNishanth Menon
u-boot standard i2c register write prototype is i2c_reg_write(u8 addr, u8 reg, u8 val) twl4030_i2c_write_u8(u8 addr, u8 val, u8 reg) does not provide consistency, so switch the prototype to be consistent with rest of u-boot i2c operations: twl4030_i2c_write_u8(u8 addr, u8 reg, u8 val) Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10ti814x_evm: enable CPSW supportMatt Porter
Adds CPSW support to the TI814X EVM configured with an ET1011C PHY in GMII mode. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-05-10am33xx: add pll and clock support for TI814x CPSWMatt Porter
Enables required PLLs and clocks for CPSW on TI814x. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-05-06imx: mx35pdk: Fix MUX2_CTR GPIOBenoît Thébaudeau
MUX2_CTR is on GPIO1[5], not GPIO2[5], and it needs to be set high in order to connect the FEC. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-06fpga: zynq: Add support for loading bitstreamMichal Simek
Devcfg device requires to load bitstream in binary format. But u-boot also has an option for loading bitstream in bit format. Let's handle both cases by zynqpl driver. Also add suport for loading partial bitstreams. The first driver version was done by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-05-06mx23_olinuxino: Do not set voltage selection bit for SSP padsFabio Estevam
mx23 SSP pad registers do not contain voltage selection bit, so just remove it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-06mx23evk: Do not set voltage selection bit for SSP padsFabio Estevam
mx23 SSP pad registers do not contain voltage selection bit, so just remove it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-05h2200: Add board reset supportŁukasz Dałek
Use Samsung S3CA410X01 companion chip to reset PDA. Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
2013-05-05imx: m53evk: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior, except for the folloing line that has been removed because the iomux mode was not set accordingly and the pad used for OTG OC is not this one: mxc_iomux_set_input(MX53_USBOH3_IPP_IND_OTG_OC_SELECT_INPUT, 1); Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx53smd: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx53loco: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx53evk: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx53ard: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: ima3-mx53: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: vision2: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior, except for older silicon revisions for which support is removed. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx51_efikamx/sb: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior, except for older silicon revisions for which support is removed. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Tested-by: Matt Sealey <matt@genesi-usa.com>
2013-05-05imx: mx51evk: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior, except for older silicon revisions for which support is removed. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: iomux-mx51: Fix MX51_PAD_EIM_CS2__GPIO2_27Benoît Thébaudeau
In ALT1 mode, EIM_CS2 is GPIO2[27], not ESDHC1.CD. Hence, rename MX51_PAD_EIM_CS2__SD1_CD to MX51_PAD_EIM_CS2__GPIO2_27. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: woodburn: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx35pdk: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx35pdk: Fix WDOG_RST iomux functionBenoît Thébaudeau
The signal connected from this pin to the PMIC is WDOG_B, i.e. ALT0 mode, not ALT1 (which even corresponds to nothing). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: flea3: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: zmx25: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior, even if some pad control values could probably be simplified. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: tx25: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior, even if some pad control values could probably be simplified. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx25pdk: Fix GPIO assignmentsBenoît Thébaudeau
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx25pdk: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior, even if some pad control values could probably be simplified. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05arm: mx5: Add support for DENX M53EVKMarek Vasut
Add basic support for the DENX M53EVK board. Currently supported is: MMC (incl. booting) NAND (incl. booting) Ethernet, I2C, USB, SATA, RTC. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Wolfgang Denk <wd@denx.de>
2013-05-05mx23_olinuxino: Fix DDR pin iomux settingsFabio Estevam
Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from Freescale, which results in much better stability. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-05mx23evk: Fix DDR pin iomux settingsFabio Estevam
Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from Freescale, which results in much better stability. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-02Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini
2013-05-02powerpc/p1_p2_rdb_pc: Add a pin to reset the DDR chip for P1021RDB-PCXu Jiucheng
When P1021RDB-PC reboot system, the board will hung at uboot DDR configuration. For P1021RDB-PC DDR reset pin is multiplex with QE, so uboot will reserve this pin for QE and skip DDR reset. Other platforms without QE will do this reset. This patch adds a slight code to reset DDR chip by QE CE_PB8 pin for NAND and NOR FLASH boot. For booting from SPI FALSH and SD card, it seems possible to use the rom on chip to write to the GPIO pins before configuring the DDR. Signed-off-by: Xu Jiucheng <B37781@freescale.com> Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02powerpc/p1010rdb: Change flexcan compatible stringShengzhou Liu
Change flexcan compatible string from "fsl,flexcan-v1.0" to "fsl,p1010-flexcan" to match the device tree. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02qoriq/p1_p2_rdb_pc: USB device-tree fixups for P1020Zhicheng Fan
Resolve P1020 second USB controller multiplexing with eLBC - mandatory to mention USB2 in hwconfig string to select it over eLBC, otherwise USB2 node is removed - works only for SPI and SD boot Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Zhicheng Fan <B32736@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02powerpc/b4860qds: Add the tlb entries for SRIO interfacesLiu Gang
Add the tlb entries based on the configuration of the SRIO interfaces. Every SRIO interface has 256M space: #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02powerpc/p1022ds: Add support for NAND and NAND boot using SPLMatthew McClintock
Add defines needed to access NAND, remove second flash bank that is actually connected to NAND. Add nand booting support for P1022DS with hardcoded DDR config using SPL framework from 2011 Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Jiang Yutang <b14898@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02board/freescale/common/cds_pci_ft.c: Fix rotate wrong cells in interrupt-map ↵Jiang Bin
property For linux 3.x, the size of each item in interrupt-map property is 9 not 7. Don't use the static value and calculate the size with following cells: PCI #address-cells, PCI #interrupt-cells, PIC address, PIC #address-cells, PIC #interrupt-cells. Signed-off-by: Bin Jiang <bin.jiang@windriver.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxxTom Rini
2013-05-02mpc5200: a3m071/a4m2k: Miscellaneous updates and fixesStefan Roese
The changes to a3m071/a4m2k in summary are: - Enable CAN1 on I2C in GPS Port Configuration - Enable SPI on PSC2 - Activate network console - New flash partitioning - Fix some typos - Pass host name to Linux - Change rootfs to squashfs,jffs2 - Enable UBI/UBIFS support - Enable FIT support Signed-off-by: Stefan Roese <sr@denx.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-01 14:30:14 +0000