summaryrefslogtreecommitdiff
path: root/include/configs/TOP5200.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/TOP5200.h')
-rw-r--r--include/configs/TOP5200.h160
1 files changed, 96 insertions, 64 deletions
diff --git a/include/configs/TOP5200.h b/include/configs/TOP5200.h
index 21daa2d971..624beed31a 100644
--- a/include/configs/TOP5200.h
+++ b/include/configs/TOP5200.h
@@ -1,16 +1,17 @@
/*
* (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * modified for TOP5200 by Reinhard Meyer, www.emk-elektronik.de
- * TOP5200 differences from IceCube:
- * 1 FLASH Bank for one Chip only, up to 64 MB in 16 MB Banks
- * bank switch controlled by TIMER_6(LSB) and TIMER_7(MSB) Pins
- * 1 SDRAM/DDRAM Bank up to 256 MB
- * local VPD I2C Bus is software driven and uses
- * GPIO_WKUP_6 for SDA, GPIO_WKUP_7 for SCL
- * FLASH is located at 0x80000000
- * Internal regs are at 0xfff00000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * modified for TOP5200-series by Reinhard Meyer, www.emk-elektronik.de
+ *
+ * TOP5200 differences from IceCube:
+ * 1 FLASH Bank for one Chip only, up to 64 MB in 16 MB Banks
+ * bank switch controlled by TIMER_6(LSB) and TIMER_7(MSB) Pins
+ * 1 SDRAM/DDRAM Bank up to 256 MB
+ * local VPD I2C Bus is software driven and uses
+ * GPIO_WKUP_6 for SDA, GPIO_WKUP_7 for SCL
+ * FLASH is re-located at 0xff000000
+ * Internal regs are at 0xf0000000
* Reset jumps to 0x00000100
*
* See file CREDITS for list of people who contributed to this
@@ -44,7 +45,7 @@
#define CONFIG_MPC5200 1 /* More exactly a MPC5200 */
#define CONFIG_TOP5200 1 /* ... on TOP5200 board - we need this for FEC.C */
-#define CFG_MPC5XXX_CLKIN 33333333 /* ... running at 33MHz */
+#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
@@ -98,17 +99,48 @@
#include <cmd_confdefs.h>
/*
+ * low boot
+ */
+#if (TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
+# define CFG_LOWBOOT 1
+# define CFG_LOWBOOT16 1
+#endif
+
+/*
* Autobooting
*/
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#define CONFIG_BOOTCOMMAND "bootm 100000" /* autoboot command */
-#define CONFIG_BOOTARGS "root=/dev/ram rw"
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo"
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$(serverip):$(rootpath)\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs $(bootargs) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
+ ":$(hostname):$(netdev):off panic=1\0" \
+ "flash_nfs=run nfsargs addip;" \
+ "bootm $(kernel_addr)\0" \
+ "flash_self=run ramargs addip;" \
+ "bootm $(kernel_addr) $(ramdisk_addr)\0" \
+ "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
+ "rootpath=/opt/eldk/ppc_82xx\0" \
+ "bootfile=/tftpboot/MPC5200/uImage\0" \
+ ""
+
+#define CONFIG_BOOTCOMMAND "run flash_self"
/*
* IPB Bus clocking configuration.
*/
#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
-
+
/*
* I2C configuration
*/
@@ -120,21 +152,21 @@
#define CFG_I2C_EEPROM_ADDR_LEN 2
#define CFG_EEPROM_SIZE 0x2000
-
+
#define CONFIG_ENV_OVERWRITE
#define CONFIG_MISC_INIT_R
-
+
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1
-
+
#if defined (CONFIG_SOFT_I2C)
# define SDA0 0x40
# define SCL0 0x80
-# define GPIOE0 *((volatile uchar*)(CFG_MBAR+0x0c00))
-# define DDR0 *((volatile uchar*)(CFG_MBAR+0x0c08))
-# define DVO0 *((volatile uchar*)(CFG_MBAR+0x0c0c))
-# define DVI0 *((volatile uchar*)(CFG_MBAR+0x0c20))
-# define ODE0 *((volatile uchar*)(CFG_MBAR+0x0c04))
+# define GPIOE0 *((volatile uchar*)(CFG_MBAR+0x0c00))
+# define DDR0 *((volatile uchar*)(CFG_MBAR+0x0c08))
+# define DVO0 *((volatile uchar*)(CFG_MBAR+0x0c0c))
+# define DVI0 *((volatile uchar*)(CFG_MBAR+0x0c20))
+# define ODE0 *((volatile uchar*)(CFG_MBAR+0x0c04))
# define I2C_INIT {GPIOE0|=(SDA0|SCL0);ODE0|=(SDA0|SCL0);DVO0|=(SDA0|SCL0);DDR0|=(SDA0|SCL0);}
# define I2C_READ ((DVI0&SDA0)?1:0)
# define I2C_SDA(x) {if(x)DVO0|=SDA0;else DVO0&=~SDA0;}
@@ -145,12 +177,12 @@
# define CFG_I2C_SPEED 100000
# define CFG_I2C_SLAVE 0x7F
#endif
-
-#if defined (CONFIG_HARD_I2C)
+
+#if defined (CONFIG_HARD_I2C)
# define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */
# define CFG_I2C_SPEED 100000 /* 100 kHz */
# define CFG_I2C_SLAVE 0x7F
-#endif
+#endif
/*
* Flash configuration, expect one 16 Megabyte Bank at most
@@ -158,7 +190,7 @@
#define CFG_FLASH_BASE 0xff000000
#define CFG_FLASH_SIZE 0x01000000
#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
-#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0)
+#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0)
#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */
@@ -167,32 +199,32 @@
#undef CONFIG_FLASH_16BIT /* Flash is 8-bit */
-/*
- * DRAM configuration - will be read from VPD later... TODO!
- */
-#if 0
-/* 2x MT48LC16M16A2 - 7.0 ns SDRAMS = 64 MegaBytes Total */
-#define CFG_DRAM_DDR 0
-#define CFG_DRAM_EMODE 0
-#define CFG_DRAM_MODE 0x008D
-#define CFG_DRAM_CONTROL 0x514F0000
-#define CFG_DRAM_CONFIG1 0xC2233A00
-#define CFG_DRAM_CONFIG2 0x88B70004
-#define CFG_DRAM_TAP_DEL 0x08
-#define CFG_DRAM_RAM_SIZE 0x19
-#endif
-#if 1
-/* 2x MT48LC16M16A2 - 7.5 ns SDRAMS = 64 MegaBytes Total */
-#define CFG_DRAM_DDR 0
-#define CFG_DRAM_EMODE 0
-#define CFG_DRAM_MODE 0x00CD
-#define CFG_DRAM_CONTROL 0x514F0000
-#define CFG_DRAM_CONFIG1 0xD2333A00
-#define CFG_DRAM_CONFIG2 0x8AD70004
-#define CFG_DRAM_TAP_DEL 0x08
-#define CFG_DRAM_RAM_SIZE 0x19
-#endif
-
+/*
+ * DRAM configuration - will be read from VPD later... TODO!
+ */
+#if 0
+/* 2x MT48LC16M16A2 - 7.0 ns SDRAMS = 64 MegaBytes Total */
+#define CFG_DRAM_DDR 0
+#define CFG_DRAM_EMODE 0
+#define CFG_DRAM_MODE 0x008D
+#define CFG_DRAM_CONTROL 0x514F0000
+#define CFG_DRAM_CONFIG1 0xC2233A00
+#define CFG_DRAM_CONFIG2 0x88B70004
+#define CFG_DRAM_TAP_DEL 0x08
+#define CFG_DRAM_RAM_SIZE 0x19
+#endif
+#if 1
+/* 2x MT48LC16M16A2 - 7.5 ns SDRAMS = 64 MegaBytes Total */
+#define CFG_DRAM_DDR 0
+#define CFG_DRAM_EMODE 0
+#define CFG_DRAM_MODE 0x00CD
+#define CFG_DRAM_CONTROL 0x514F0000
+#define CFG_DRAM_CONFIG1 0xD2333A00
+#define CFG_DRAM_CONFIG2 0x8AD70004
+#define CFG_DRAM_TAP_DEL 0x08
+#define CFG_DRAM_RAM_SIZE 0x19
+#endif
+
/*
* Environment settings
*/
@@ -201,17 +233,17 @@
#define CFG_ENV_SIZE 0x0700
#define CFG_I2C_EEPROM_ADDR 0x57
-/*
- * VPD settings
- */
+/*
+ * VPD settings
+ */
#define CFG_FACT_OFFSET 0x1800
#define CFG_FACT_SIZE 0x0800
#define CFG_I2C_FACT_ADDR 0x57
-
+
/*
- * Memory map
- *
- * Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000
+ * Memory map
+ *
+ * Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000
*/
#define CFG_MBAR 0xf0000000 /* DO NOT CHANGE this */
#define CFG_SDRAM_BASE 0x00000000
@@ -240,12 +272,12 @@
*/
#define CONFIG_MPC5XXX_FEC 1
#define CONFIG_FEC_10MBIT 1 /* Workaround for FEC 100Mbit problem */
-#define CONFIG_PHY_ADDR 0x1f
+#define CONFIG_PHY_ADDR 0x1f
#define CONFIG_PHY_TYPE 0x79c874
/*
- * GPIO configuration:
- * PSC1,2,3 predefined as UART
- * PCI disabled
+ * GPIO configuration:
+ * PSC1,2,3 predefined as UART
+ * PCI disabled
* Ethernet 100 with MD
*/
#define CFG_GPS_PORT_CONFIG 0x00058444