1 files changed, 0 insertions, 88 deletions
diff --git a/common/cmd_mmc_spi.c b/common/cmd_mmc_spi.c
deleted file mode 100644
index a2138b8650..0000000000
--- a/common/cmd_mmc_spi.c
+++ /dev/null
@@ -1,88 +0,0 @@
-/*
- * Command for mmc_spi setup.
- *
- * Copyright (C) 2010 Thomas Chou <thomas@wytron.com.tw>
- * Licensed under the GPL-2 or later.
- */
-
-#include <common.h>
-#include <mmc.h>
-#include <spi.h>
-
-#ifndef CONFIG_MMC_SPI_BUS
-# define CONFIG_MMC_SPI_BUS 0
-#endif
-#ifndef CONFIG_MMC_SPI_CS
-# define CONFIG_MMC_SPI_CS 1
-#endif
-/* in SPI mode, MMC speed limit is 20MHz, while SD speed limit is 25MHz */
-#ifndef CONFIG_MMC_SPI_SPEED
-# define CONFIG_MMC_SPI_SPEED 25000000
-#endif
-/* MMC and SD specs only seem to care that sampling is on the
- * rising edge ... meaning SPI modes 0 or 3.  So either SPI mode
- * should be legit.  We'll use mode 0 since the steady state is 0,
- * which is appropriate for hotplugging, unless the platform data
- * specify mode 3 (if hardware is not compatible to mode 0).
- */
-#ifndef CONFIG_MMC_SPI_MODE
-# define CONFIG_MMC_SPI_MODE SPI_MODE_0
-#endif
-
-static int do_mmc_spi(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-	uint bus = CONFIG_MMC_SPI_BUS;
-	uint cs = CONFIG_MMC_SPI_CS;
-	uint speed = CONFIG_MMC_SPI_SPEED;
-	uint mode = CONFIG_MMC_SPI_MODE;
-	char *endp;
-	struct mmc *mmc;
-
-	if (argc < 2)
-		goto usage;
-
-	cs = simple_strtoul(argv[1], &endp, 0);
-	if (*argv[1] == 0 || (*endp != 0 && *endp != ':'))
-		goto usage;
-	if (*endp == ':') {
-		if (endp[1] == 0)
-			goto usage;
-		bus = cs;
-		cs = simple_strtoul(endp + 1, &endp, 0);
-		if (*endp != 0)
-			goto usage;
-	}
-	if (argc >= 3) {
-		speed = simple_strtoul(argv[2], &endp, 0);
-		if (*argv[2] == 0 || *endp != 0)
-			goto usage;
-	}
-	if (argc >= 4) {
-		mode = simple_strtoul(argv[3], &endp, 16);
-		if (*argv[3] == 0 || *endp != 0)
-			goto usage;
-	}
-	if (!spi_cs_is_valid(bus, cs)) {
-		printf("Invalid SPI bus %u cs %u\n", bus, cs);
-		return 1;
-	}
-
-	mmc = mmc_spi_init(bus, cs, speed, mode);
-	if (!mmc) {
-		printf("Failed to create MMC Device\n");
-		return 1;
-	}
-	printf("%s: %d at %u:%u hz %u mode %u\n", mmc->cfg->name, mmc->block_dev.dev,
-	       bus, cs, speed, mode);
-	mmc_init(mmc);
-	return 0;
-
-usage:
-	return CMD_RET_USAGE;
-}
-
-U_BOOT_CMD(
-	mmc_spi,	4,	0,	do_mmc_spi,
-	"mmc_spi setup",
-	"[bus:]cs [hz] [mode]	- setup mmc_spi device"
-);