diff options
Diffstat (limited to 'board/Barix/ipam390/ipam390-ais-uart.cfg')
| -rw-r--r-- | board/Barix/ipam390/ipam390-ais-uart.cfg | 202 |
1 files changed, 202 insertions, 0 deletions
diff --git a/board/Barix/ipam390/ipam390-ais-uart.cfg b/board/Barix/ipam390/ipam390-ais-uart.cfg new file mode 100644 index 0000000000..e1a99f278b --- /dev/null +++ b/board/Barix/ipam390/ipam390-ais-uart.cfg @@ -0,0 +1,202 @@ +; General settings that can be overwritten in the host code +; that calls the AISGen library. +[General] + +; Can be 8 or 16 - used in emifa +busWidth=8 + +; SPIMASTER,I2CMASTER,EMIFA,NAND,EMAC,UART,PCI,HPI,USB,MMC_SD,VLYNQ,RAW +BootMode=UART + +; 8,16,24 - used for SPI,I2C +;AddrWidth=8 + +; NO_CRC,SECTION_CRC,SINGLE_CRC +crcCheckType=NO_CRC + +; This section allows setting the PLL0 system clock with a +; specified multiplier and divider as shown. The clock source +; can also be chosen for internal or external. +; |------24|------16|-------8|-------0| +; PLL0CFG0: | CLKMODE| PLLM | PREDIV | POSTDIV| +; PLL0CFG1: | RSVD | PLLDIV1| PLLDIV3| PLLDIV7| +;[PLL0CONFIG] +;PLL0CFG0 = 0x00180001 +;PLL0CFG1 = 0x00000205 + +[PLLANDCLOCKCONFIG] +PLL0CFG0 = 0x00180001 +PLL0CFG1 = 0x00000205 +PERIPHCLKCFG = 0x00000051 + +; This section allows setting up the PLL1. Usually this will +; take place as part of the EMIF3a DDR setup. The format of +; the input args is as follows: +; |------24|------16|-------8|-------0| +; PLL1CFG0: | PLLM| POSTDIV| PLLDIV1| PLLDIV2| +; PLL1CFG1: | RSVD | PLLDIV3| +[PLL1CONFIG] +PLL1CFG0 = 0x18010001 +PLL1CFG1 = 0x00000002 + +; This section lets us configure the peripheral interface +; of the current booting peripheral (I2C, SPI, or UART). +; Use with caution. The format of the PERIPHCLKCFG field +; is as follows: +; SPI: |------24|------16|-------8|-------0| +; | RSVD |PRESCALE| +; +; I2C: |------24|------16|-------8|-------0| +; | RSVD |PRESCALE| CLKL | CLKH | +; +; UART: |------24|------16|-------8|-------0| +; | RSVD | OSR | DLH | DLL | +[PERIPHCLKCFG] +PERIPHCLKCFG = 0x00000051 + +; This section can be used to configure the PLL1 and the EMIF3a registers +; for starting the DDR2 interface. +; See PLL1CONFIG section for the format of the PLL1CFG fields. +; |------24|------16|-------8|-------0| +; PLL1CFG0: | PLL1CFG | +; PLL1CFG1: | PLL1CFG | +; DDRPHYC1R: | DDRPHYC1R | +; SDCR: | SDCR | +; SDTIMR: | SDTIMR | +; SDTIMR2: | SDTIMR2 | +; SDRCR: | SDRCR | +; CLK2XSRC: | CLK2XSRC | +[EMIF3DDR] +PLL1CFG0 = 0x18010001 +PLL1CFG1 = 0x00000002 +DDRPHYC1R = 0x000000C2 +SDCR = 0x0017C432 +SDTIMR = 0x26922A09 +SDTIMR2 = 0x4414C722 +SDRCR = 0x00000498 +CLK2XSRC = 0x00000000 + +; This section can be used to configure the EMIFA to use +; CS0 as an SDRAM interface. The fields required to do this +; are given below. +; |------24|------16|-------8|-------0| +; SDBCR: | SDBCR | +; SDTIMR: | SDTIMR | +; SDRSRPDEXIT: | SDRSRPDEXIT | +; SDRCR: | SDRCR | +; DIV4p5_CLK_ENABLE: | DIV4p5_CLK_ENABLE | +;[EMIF25SDRAM] +;SDBCR = 0x00004421 +;SDTIMR = 0x42215810 +;SDRSRPDEXIT = 0x00000009 +;SDRCR = 0x00000410 +;DIV4p5_CLK_ENABLE = 0x00000001 + +; This section can be used to configure the async chip selects +; of the EMIFA (CS2-CS5). The fields required to do this +; are given below. +; |------24|------16|-------8|-------0| +; A1CR: | A1CR | +; A2CR: | A2CR | +; A3CR: | A3CR | +; A4CR: | A4CR | +; NANDFCR: | NANDFCR | +;[EMIF25ASYNC] +;A1CR = 0x00000000 +;A2CR = 0x00000000 +;A3CR = 0x00000000 +;A4CR = 0x00000000 +;NANDFCR = 0x00000000 +[EMIF25ASYNC] +A1CR = 0x00000000 +A2CR = 0x3FFFFFFE +A3CR = 0x00000000 +A4CR = 0x00000000 +NANDFCR = 0x00000012 + +; This section should be used in place of PLL0CONFIG when +; the I2C, SPI, or UART modes are being used. This ensures that +; the system PLL and the peripheral's clocks are changed together. +; See PLL0CONFIG section for the format of the PLL0CFG fields. +; See PERIPHCLKCFG section for the format of the CLKCFG field. +; |------24|------16|-------8|-------0| +; PLL0CFG0: | PLL0CFG | +; PLL0CFG1: | PLL0CFG | +; PERIPHCLKCFG: | CLKCFG | +;[PLLANDCLOCKCONFIG] +;PLL0CFG0 = 0x00180001 +;PLL0CFG1 = 0x00000205 +;PERIPHCLKCFG = 0x00010032 + +; This section should be used to setup the power state of modules +; of the two PSCs. This section can be included multiple times to +; allow the configuration of any or all of the device modules. +; |------24|------16|-------8|-------0| +; LPSCCFG: | PSCNUM | MODULE | PD | STATE | +;[PSCCONFIG] +;LPSCCFG= + +; This section allows setting of a single PINMUX register. +; This section can be included multiple times to allow setting +; as many PINMUX registers as needed. +; |------24|------16|-------8|-------0| +; REGNUM: | regNum | +; MASK: | mask | +; VALUE: | value | +;[PINMUX] +;REGNUM = 5 +;MASK = 0x00FF0000 +;VALUE = 0x00880000 + +; No Params required - simply include this section for the fast boot +; function to be called +;[FASTBOOT] + +; This section allows setting up the PLL1. Usually this will +; take place as part of the EMIF3a DDR setup. The format of +; the input args is as follows: +; |------24|------16|-------8|-------0| +; PLL1CFG0: | PLLM| POSTDIV| PLLDIV1| PLLDIV2| +; PLL1CFG1: | RSVD | PLLDIV3| +;[PLL1CONFIG] +;PLL1CFG0 = 0x15010001 +;PLL1CFG1 = 0x00000002 + +; This section can be used to configure the PLL1 and the EMIF3a registers +; for starting the DDR2 interface on ARM-boot D800K002 devices. +; |------24|------16|-------8|-------0| +; DDRPHYC1R: | DDRPHYC1R | +; SDCR: | SDCR | +; SDTIMR: | SDTIMR | +; SDTIMR2: | SDTIMR2 | +; SDRCR: | SDRCR | +; CLK2XSRC: | CLK2XSRC | +;[ARM_EMIF3DDR_PATCHFXN] +;DDRPHYC1R = 0x000000C2 +;SDCR = 0x0017C432 +;SDTIMR = 0x26922A09 +;SDTIMR2 = 0x4414C722 +;SDRCR = 0x00000498 +;CLK2XSRC = 0x00000000 + +; This section can be used to configure the PLL1 and the EMIF3a registers +; for starting the DDR2 interface on DSP-boot D800K002 devices. +; |------24|------16|-------8|-------0| +; DDRPHYC1R: | DDRPHYC1R | +; SDCR: | SDCR | +; SDTIMR: | SDTIMR | +; SDTIMR2: | SDTIMR2 | +; SDRCR: | SDRCR | +; CLK2XSRC: | CLK2XSRC | +;[DSP_EMIF3DDR_PATCHFXN] +;DDRPHYC1R = 0x000000C4 +;SDCR = 0x08134632 +;SDTIMR = 0x26922A09 +;SDTIMR2 = 0x0014C722 +;SDRCR = 0x00000492 +;CLK2XSRC = 0x00000000 + +;[INPUTFILE] +;FILENAME=u-boot.bin +;LOADADDRESS=0xC1080000 +;ENTRYPOINTADDRESS=0xC1080000 |