Merge branch 'master' of /home/wd/git/u-boot/custodians

* 'master' of /home/wd/git/u-boot/custodians:
  arm, davinci: add DAVINCI_MMC_CLKID
  arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
  arm, davinci: da850/dm365 lowlevel cleanup
  omap5: Add omap5_evm board build support.
  omap4/5: Add support for booting with CH.
  omap5: emif: Add emif/ddr configurations required for omap5 evm
  omap5: clocks: Add clocks support for omap5 platform.
  omap5: Add minimal support for omap5430.
  omap: Checkpatch fixes
  omap4: make omap4 code common for future reuse
  GCC4.6: Squash warnings in onenand_base.c
  GCC4.6: Fix common/usb.c on xscale
  OneNAND: Add simple OneNAND SPL
  PXA: vpac270: Enable the new generic MMC driver
  PXA: Cleanup serial_pxa
  PXA: Drop csb226 and innokom boards (unmaintained)
  m28evk: Fix comment about the number of RAM banks
  mx31: Fix checkpatch warnings in generic.c
  mx31: Use proper IO accessor for GPR register
  mx31: Remove duplicate definition for GPR register
  qong: Use generic function for configuring GPR register
  M28EVK: Enable USB HOST support
  iMX28: Add USB HOST driver
  iMX28: Add USB and USB PHY register definitions
  M28: Add memory detection into SPL
  iMX28: Fix ARM vector handling
  M28: Add doc/README.m28 documentation
  M28: Add MMC SPL
  iMX28: Add support for DENX M28EVK board
  iMX28: Add u-boot.sb target to Makefile
  iMX28: Add image header generator tool
  iMX28: Add driver for internal RTC
  iMX28: Add GPMI NAND driver
  iMX28: Add APBH DMA driver
  iMX28: Add SPI driver
  iMX28: Add GPIO control
  iMX28: Add I2C bus driver
  iMX28: Add PINMUX control
  FEC: Add support for iMX28 quirks
  iMX28: Add SSP MMC driver
  iMX28: Initial support for iMX28 CPU
  MX25: zmx25: GCC4.6 fix build warnings
  da850: add new config file for AM18xx
  BeagleBoard: config: Switch to ttyO2
  OMAP3: Change omap3_evm maintainer
  devkit8000: Fix NAND SPL on boards with 256MB NAND
  integrator: enable Vpp and disable flash protection
  integrator: add system controller header
  integrator: make flash writeable on boot
  integrator: use io-accessors for board init
  integrator: move text offset to config
  integrator: pass configs for core modules
  ARM: remove superfluous setting of arch_number in board specific code.
  SPL: Allow ARM926EJS to avoid compiling in the CPU support code
  integrator: do not test first part of the memory
  arm: a320: fix broken timer
  ARM: define CONFIG_MACH_TYPE for all ronetix boards
  dm646x: pass board revision info to kernel
  dm646x: add new configuration for dm6467T
  arm, davinci: Fix setting of the SDRAM configuration register
  arm, davinci: Remove the duplication of LPSC functions
  arm, davinci: Rename AM1808 lowlevel functions to DA850
  da8xxevm: fix build error
  ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE

1 files changed, 9 insertions, 4 deletions

diff --git a/common/usb.c b/common/usb.c
index bed5116505..4418c70f46 100644
--- a/common/usb.c
+++ b/common/usb.c
@@ -263,18 +263,24 @@ int usb_maxpacket(struct usb_device *dev, unsigned long pipe)
 		return dev->epmaxpacketin[((pipe>>15) & 0xf)];
 }
 
-/* The routine usb_set_maxpacket_ep() is extracted from the loop of routine
+/*
+ * The routine usb_set_maxpacket_ep() is extracted from the loop of routine
  * usb_set_maxpacket(), because the optimizer of GCC 4.x chokes on this routine
  * when it is inlined in 1 single routine. What happens is that the register r3
  * is used as loop-count 'i', but gets overwritten later on.
  * This is clearly a compiler bug, but it is easier to workaround it here than
  * to update the compiler (Occurs with at least several GCC 4.{1,2},x
  * CodeSourcery compilers like e.g. 2007q3, 2008q1, 2008q3 lite editions on ARM)
+ *
+ * NOTE: Similar behaviour was observed with GCC4.6 on ARMv5.
  */
 static void  __attribute__((noinline))
-usb_set_maxpacket_ep(struct usb_device *dev, struct usb_endpoint_descriptor *ep)
+usb_set_maxpacket_ep(struct usb_device *dev, int if_idx, int ep_idx)
 {
 	int b;
+	struct usb_endpoint_descriptor *ep;
+
+	ep = &dev->config.if_desc[if_idx].ep_desc[ep_idx];
 
 	b = ep->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK;
 
@@ -313,8 +319,7 @@ int usb_set_maxpacket(struct usb_device *dev)
 
 	for (i = 0; i < dev->config.desc.bNumInterfaces; i++)
 		for (ii = 0; ii < dev->config.if_desc[i].desc.bNumEndpoints; ii++)
-			usb_set_maxpacket_ep(dev,
-					  &dev->config.if_desc[i].ep_desc[ii]);
+			usb_set_maxpacket_ep(dev, i, ii);
 
 	return 0;
 }