summaryrefslogtreecommitdiff
path: root/Documentation/devicetree
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@linux-foundation.org>2016-05-19 12:50:56 -0700
committerLinus Torvalds <torvalds@linux-foundation.org>2016-05-19 12:50:56 -0700
commita37571a29eca963562ff5a9233db4a5c73c72cf9 (patch)
treeec78d4b5b905f32bc541b2faa5b89f88967cf990 /Documentation/devicetree
parenta0d3c7c5c07cfbe00ab89438ddf82482f5a99422 (diff)
parent0d5358330c20d50e52e3e65ff07a5db8007041fc (diff)
Merge tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij: "This kernel cycle was quite calm when it comes to pin control and there is really just one major change, and that is the introduction of devm_pinctrl_register() managed resources. Apart from that linear development, details below. Core changes: - Add the devm_pinctrl_register() API and switch all applicable drivers to use it, saving lots of lines of code all over the place. New drivers: - driver for the Broadcom NS2 SoC - subdriver for the PXA25x SoCs - subdriver for the AMLogic Meson GXBB SoC Driver improvements: - the Intel Baytrail driver now properly supports pin control - Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction() callback in the GPIO portions - continued development and stabilization of several SH-PFC SoC subdrivers: r8a7795, r8a7790, r8a7794 etc" * tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits) Revert "pinctrl: tegra: avoid parked_reg and parked_bank" pinctrl: meson: Fix eth_tx_en bit index pinctrl: tegra: avoid parked_reg and parked_bank pinctrl: tegra: Correctly check the supported configuration pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC pinctrl: rockchip: fix pull setting error for rk3399 pinctrl: stm32: Implement .pin_config_dbg_show() pinctrl: nomadik: hide nmk_gpio_get_mode when unused pinctrl: ns2: rename pinctrl_utils_dt_free_map pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable pinctrl: at91: Make at91_gpio_template const pinctrl: baytrail: fix some error handling in debugfs pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove() pinctrl: nomadik: implement .get_direction() pinctrl: nomadik: use BIT() with offsets consequently pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration ...
Diffstat (limited to 'Documentation/devicetree')
-rw-r--r--Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt4
1 files changed, 2 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
index ffadb7a371f6..74e6ec0339d6 100644
--- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
@@ -72,8 +72,8 @@ Pin Configuration Node Properties:
The pin configuration parameters use the generic pinconf bindings defined in
pinctrl-bindings.txt in this directory. The supported parameters are
-bias-disable, bias-pull-up, bias-pull-down and power-source. For pins that
-have a configurable I/O voltage, the power-source value should be the
+bias-disable, bias-pull-up, bias-pull-down, drive strength and power-source. For
+pins that have a configurable I/O voltage, the power-source value should be the
nominal I/O voltage in millivolts.