; A31 uQseven module [product] version = "301" machine = "pangolin" [platform] eraseflag = 1 [fel_key] fel_key_type = 1 ;---------------------------------------------------------------------------------- ; system configuration ; ? ;dcdc1_vol ---set dcdc1 voltage,mV,1600-3400,100mV/step ;dcdc2_vol ---set dcdc2 voltage,mV,600-1540,20mV/step ;dcdc3_vol ---set dcdc3 voltage,mV,600-1860,20mV/step ;dcdc4_vol ---set dcdc4 voltage,mV,600-1540,20mV/step ;dcdc5_vol ---set dcdc5 voltage,mV,1000-2550,50mV/step ;aldo2_vol ---set aldo2 voltage,mV,700-3300,100mV/step ;aldo3_vol ---set aldo3 voltage,mV,700-3300,100mV/step ;---------------------------------------------------------------------------------- ; power_start meaning ; ; @ 0: Do not allow direct power plug adapters must pass judgment: to ; meet the following conditions Direct Power On: Long press power ; button, the previous system status is, if the battery is low, you ; can not boot ; @ 1: in any state, allowing direct plug adapters power while ; requiring high enough battery power ; @ 2: Do not allow direct power plug adapters must pass judgment: to ; meet the following conditions Direct Power On: Long press power ; button, the previous system status is not required to battery power ; @ 3: any state that allows direct power plug adapters do not require ; battery power [target] boot_clock = 1008 storage_type = -1 power_start = 3 [power_sply] dcdc1_vol = 3300 dcdc2_vol = 1200 dcdc3_vol = 1260 dcdc4_vol = 1260 ; dcdc4_vol = 1100 dcdc5_vol = 1500 aldo1_vol = 0 aldo2_vol = 1800 aldo3_vol = 3000 eldo1_vol = 0 eldo2_vol = 0 eldo3_vol = 0 [card_boot] logical_start = 40960 sprite_gpio0 = ;--------------------------------------------------------------------------------------------------------- ; if 1 == standby_mode, then support super standby; ; else, support normal standby. ;--------------------------------------------------------------------------------------------------------- [pm_para] standby_mode = 0 dram_selfresh_en = 0 [card0_boot_para] card_ctrl = 0 card_high_speed = 1 card_line = 4 sdc_d1 = port:PF0<2><1> sdc_d0 = port:PF1<2><1> sdc_clk = port:PF2<2><1> sdc_cmd = port:PF3<2><1> sdc_d3 = port:PF4<2><1> sdc_d2 = port:PF5<2><1> ;[card2_boot_para] ;card_ctrl = 2 ;card_high_speed = 1 ;card_line = 8 ;sdc_clk = port:PC07<3><1><2> ;sdc_cmd = port:PC06<3><1><2> ;sdc_d0 = port:PC08<3><1><2> ;sdc_d1 = port:PC09<3><1><2> ;sdc_d2 = port:PC10<3><1><2> ;sdc_d3 = port:PC11<3><1><2> ;sdc_d4 = port:PC12<3><1><2> ;sdc_d5 = port:PC13<3><1><2> ;sdc_d6 = port:PC14<3><1><2> ;sdc_d7 = port:PC15<3><1><2> [twi_para] twi_port = 0 twi_scl = port:PH14<2> twi_sda = port:PH15<2> [uart_para] ;uart_debug_port = 2 ;uart_debug_tx = port:PG06<2><1> ;uart_debug_rx = port:PG07<2><1> uart_debug_port = 0 uart_debug_tx = port:PH20<2><1> uart_debug_rx = port:PH21<2><1> [jtag_para] jtag_enable = 1 jtag_ms = port:PH9<3> jtag_ck = port:PH10<3> jtag_do = port:PH11<3> jtag_di = port:PH12<3> [clock] pll3 = 297 pll4 = 300 pll6 = 600 pll7 = 297 pll8 = 360 pll9 = 297 pll10 = 702 ;***************************************************************************** ;sdram configuration ; ;***************************************************************************** ;[dram_para] ;dram_clk = 360 ;dram_type = 3 ;dram_zq = 0x46 ;;;dram_clk = 624 ;;;dram_type = 3 ;;;dram_zq = 0xbb ;dram_odt_en = 0 ;dram_para1 = 0x10e20400 ;dram_para2 = 0x1101 ;dram_mr0 = 0x1a50 ;dram_mr1 = 0x04 ;dram_mr2 = 0x18 ;dram_mr3 = 0 ;dram_tpr0 = 0 ;dram_tpr1 = 0x80000800 ;dram_tpr2 = 0x39a70140 ;dram_tpr3 = 0xa092e74c ;dram_tpr4 = 0x2948c209 ;dram_tpr5 = 0x8944422c ;;;;dram_tpr6 = 0x30028480 ;dram_tpr6 = 0x300284a0 ;dram_tpr7 = 0x2a3297 ;dram_tpr8 = 0x5034fa8 ;dram_tpr9 = 0x36353d8 ;dram_tpr10 = 0 ;dram_tpr11 = 0 ;dram_tpr12 = 0 ;dram_tpr13 = 0 [dram_para] dram_clk = 480 dram_type = 3 dram_zq = 0x46 dram_odt_en = 1 dram_para1 = 0x10e20400 dram_para2 = 0x1101 dram_mr0 = 0x1640 dram_mr1 = 0x0040 dram_mr2 = 0x0008 dram_mr3 = 0x0000 dram_tpr0 = 0 dram_tpr1 = 0x80000400 dram_tpr2 = 0x3ea70140 dram_tpr3 = 0xa08b063c dram_tpr4 = 0x2946c208 dram_tpr5 = 0x67443a23 dram_tpr6 = 0x30028580 dram_tpr7 = 0x002a3297 dram_tpr8 = 0x05034fa8 dram_tpr9 = 0x036353d8 dram_tpr10 = 0 dram_tpr11 = 0 dram_tpr12 = 0 dram_tpr13 = 0 ;---------------------------------------------------------------------------------- ;os life cycle para configuration ;---------------------------------------------------------------------------------- ;------------------------------------------------------------------------------; ; 10/100/100Mbps Ethernet MAC Controller Configure ; ;------------------------------------------------------------------------------; ; 配置选项： ; ; gmac_used --- 1: gmac used, 0: not used ; ;------------------------------------------------------------------------------; ; MII GMII RGMII MII GMII RGMII MII GMII RGMII ; ;PA00~03 * * * PA10 * * PA20 * * * ; ; PA04 * PA11~14 * * * PA21 * * ; ; PA05 * PA15 * PA22 * * ; ; PA06 * PA16 * PA23 * * ; ; PA07 * PA17 * PA24 * * ; ; PA08 * * PA18 * PA25 * * ; ; PA09 * * * PA19 * * * PA26~27 * * * ; ;------------------------------------------------------------------------------; [gmac_para] gmac_used = 1 gmac_txd0 = port:PA00<2><3> gmac_txd1 = port:PA01<2><3> gmac_txd2 = port:PA02<2><3> gmac_txd3 = port:PA03<2><3> gmac_txclk = port:PA10<2><3> gmac_txen = port:PA09<2><3> ;gmac_gtxclk = port:PA10<2><3> gmac_rxd0 = port:PA11<2><3> gmac_rxd1 = port:PA12<2><3> gmac_rxd2 = port:PA13<2><3> gmac_rxd3 = port:PA14<2><3> gmac_rxdv = port:PA19<2><3> gmac_rxclk = port:PA20<2><3> ;gmac_txerr = port:PA21<2><3> ;gmac_rxerr = port:PA22<2><3> ;gmac_col = port:PA23<2><3> ;gmac_crs = port:PA24<2><3> gmac_clkin = port:PA25<2><3> gmac_mdc = port:PA26<2><1><3> gmac_mdio = port:PA27<2><1><3> ;gmac_phy_reset = port:PA07<1><3><1> ;usb_hub_reset = port:PC21<1><3><1> ;---------------------------------------------------------------------------------- ;i2c configuration ;---------------------------------------------------------------------------------- [twi0_para] twi_used = 1 twi_scl = port:PH14<2> twi_sda = port:PH15<2> [twi1_para] twi_used = 1 twi_scl = port:PH16<2> twi_sda = port:PH17<2> [twi2_para] twi_used = 1 twi_scl = port:PH18<2> twi_sda = port:PH19<2> [twi3_para] twi_used = 1 twi_scl = port:PB05<4> twi_sda = port:PB06<4> ;---------------------------------------------------------------------------------- ;uart configuration ;uart_type --- 2 (2 wire), 4 (4 wire), 8 (8 wire, full function) ;---------------------------------------------------------------------------------- ; UART0 (PH20/PH21): test points [uart_para0] uart_used = 1 uart_port = 0 uart_type = 2 uart_tx = port:PH20<2><1> uart_rx = port:PH21<2><1> ; UART1 (PA4/PA5): STM32 [uart_para1] uart_used = 1 uart_port = 1 uart_type = 2 uart_tx = port:PA04<4><1> uart_rx = port:PA05<4><1> ; UART2 (PG6-PG9): base-board [uart_para2] uart_used = 1 uart_port = 2 uart_type = 4 uart_tx = port:PG06<2><1> uart_rx = port:PG07<2><1> uart_rts = port:PG08<2><1> uart_cts = port:PG09<2><1> [uart_para3] uart_used = 0 uart_port = 3 uart_type = 4 uart_tx = port:PB05<3><1> uart_rx = port:PB06<3><1> uart_rts = port:PB04<3><1> uart_cts = port:PB00<3><1> [uart_para4] uart_used = 0 uart_port = 4 uart_type = 2 uart_tx = port:PG17<2><1> uart_rx = port:PG18<2><1> uart_rts = port:PB04<3><1> uart_cts = port:PB00<3><1> [uart_para5] uart_used = 0 uart_port = 5 uart_type = 4 uart_tx = port:PE04<3><1> uart_rx = port:PE05<3><1> uart_rts = port:PE06<3><1> uart_cts = port:PE07<3><1> ;---------------------------------------------------------------------------------- ;spi configuration ;---------------------------------------------------------------------------------- [spi0_para] spi_used = 0 spi_cs_bitmap = 1 spi_cs0 = port:PC27<3><1> spi_sclk = port:PC02<3> spi_mosi = port:PC00<3> spi_miso = port:PC01<3> [spi1_para] spi_used = 1 spi_cs_bitmap = 3 spi_cs1 = port:PG12<2><1> spi_cs0 = port:PG13<2><1> spi_sclk = port:PG14<2> spi_mosi = port:PG15<2> spi_miso = port:PG16<2> [spi2_para] spi_used = 0 spi_cs_bitmap = 1 spi_cs0 = port:PH09<2> spi_sclk = port:PH10<2> spi_mosi = port:PH11<2> spi_miso = port:PH12<2> [spi3_para] spi_used = 0 spi_cs_bitmap = 1 spi_cs0 = port:PA21<4> spi_sclk = port:PA22<4> spi_mosi = port:PA23<4> spi_miso = port:PA24<4> spi_cs1 = port:PA25<4> ;---------------------------------------------------------------------------------- ;resistance tp configuration ;---------------------------------------------------------------------------------- [rtp_para] rtp_used = 0 rtp_screen_size = 5 rtp_regidity_level = 5 rtp_press_threshold_enable = 0 rtp_press_threshold = 0x1f40 rtp_sensitive_level = 0xf rtp_exchange_x_y_flag = 0 ;---------------------------------------------------------------------------------- ;capacitor tp configuration ;external int function ;wakeup output function ;notice --- tp_int_port & tp_io_port use the same port ;---------------------------------------------------------------------------------- [ctp_para] ctp_used = 0 ctp_name = "gsl1680" ctp_twi_id = 1 ctp_twi_addr = 0x40 ctp_screen_max_x = 800 ctp_screen_max_y = 480 ctp_revert_x_flag = 0 ctp_revert_y_flag = 0 ctp_exchange_x_y_flag = 0 #ctp_int_port = port:PA23<6> #ctp_wakeup = port:PA24<1><3><1> #ctp_int_port = port:PG11<6> #ctp_wakeup = port:PG10<1><3><1> ;---------------------------------------------------------------------------------- ;touch key configuration ;---------------------------------------------------------------------------------- [tkey_para] tkey_used = 0 tkey_twi_id = tkey_twi_addr = tkey_int = ;---------------------------------------------------------------------------------- ;motor configuration ;---------------------------------------------------------------------------------- [motor_para] motor_used = 0 motor_shake = port:power3<1><1> [nand0_para] nand_support_2ch = 0 nand0_used = 0 good_block_ratio = 944 nand0_we = port:PC00<2> nand0_ale = port:PC01<2> nand0_cle = port:PC02<2> nand0_ce1 = port:PC03<2> nand0_ce0 = port:PC04<2> nand0_nre = port:PC05<2> nand0_rb0 = port:PC06<2> nand0_rb1 = port:PC07<2> nand0_d0 = port:PC08<2> nand0_d1 = port:PC09<2> nand0_d2 = port:PC10<2> nand0_d3 = port:PC11<2> nand0_d4 = port:PC12<2> nand0_d5 = port:PC13<2> nand0_d6 = port:PC14<2> nand0_d7 = port:PC15<2> nand0_ce2 = port:PC25<2> nand0_ce3 = port:PC26<2> nand0_ndqs = port:PC24<2> [nand1_para] nand1_used = 0 nand1_we = port:PH00<2> nand1_ale = port:PH01<2> nand1_cle = port:PH02<2> nand1_ce1 = port:PH03<2> nand1_ce0 = port:PH04<2> nand1_nre = port:PH05<2> nand1_rb0 = port:PH06<2> nand1_rb1 = port:PH07<2> nand1_d0 = port:PC16<3> nand1_d1 = port:PC17<3> nand1_d2 = port:PC18<3> nand1_d3 = port:PC19<3> nand1_d4 = port:PC20<3> nand1_d5 = port:PC21<3> nand1_d6 = port:PC22<3> nand1_d7 = port:PC23<3> nand1_ce2 = port:PH29<2> nand1_ce3 = port:PH30<2> nand1_ndqs = port:PH08<2> ;---------------------------------------------------------------------------------- ;disp init configuration ; ;disp_mode (0:screen0) ;screenx_output_type (0:none; 1:lcd; 3:hdmi;) ;screenx_output_mode (used for hdmi output, 0:480i 1:576i 2:480p 3:576p 4:720p50) ; (5:720p60 6:1080i50 7:1080i60 8:1080p24 9:1080p50 10:1080p60) ;fbx format (4:RGB655 5:RGB565 6:RGB556 7:ARGB1555 8:RGBA5551 9:RGB888 10:ARGB8888 12:ARGB4444) ;fbx pixel sequence (0:ARGB 1:BGRA 2:ABGR 3:RGBA) ;fbx_width,fbx_height (framebuffer horizontal/vertical pixels, fix to output resolution while equal 0) ;lcdx_backlight (lcd init backlight,the range:[0,256],default:197 ;lcdx_yy (lcd init screen bright/contrast/saturation/hue, value:0~100, default:50/50/57/50) ;---------------------------------------------------------------------------------- [boot_disp] ;output_type = 3 ;output_mode = 9 ;auto_hpd = 1 [disp_init] disp_init_enable = 1 disp_mode = 0 screen0_output_type = 3 ; screen0_output_mode = 4 screen0_output_mode = 9 screen1_output_type = 0 screen1_output_mode = 9 fb0_format = 10 fb0_pixel_sequence = 0 fb0_scaler_mode_enable = 1 fb0_width = 0 fb0_height = 0 fb1_format = 10 fb1_pixel_sequence = 0 fb1_scaler_mode_enable = 0 fb1_width = 0 fb1_height = 0 lcd0_backlight = 50 lcd1_backlight = 50 lcd0_bright = 50 lcd0_contrast = 50 lcd0_saturation = 57 lcd0_hue = 50 lcd1_bright = 50 lcd1_contrast = 50 lcd1_saturation = 57 lcd1_hue = 50 ;---------------------------------------------------------------------------------- ;lcd0 configuration ;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds; 4:dsi; 5:edp ;lcd_x: lcd horizontal resolution ;lcd_y: lcd vertical resolution ;lcd_width: width of lcd in mm ;lcd_height: height of lcd in mm ;lcd_size lcd panel size, e.g. "8.0","9.7" ;lcd_model_name lcd panel model name ;lcd_dclk_freq: in MHZ unit ;lcd_pwm_freq: in HZ unit ;lcd_pwm_pol: lcd backlight PWM polarity ;lcd_pwm_max_limit lcd backlight PWM max limit(<=255) ;lcd_hbp: hsync back porch ;lcd_ht: hsync total cycle ;lcd_vbp: vsync back porch ;lcd_vt: vysnc total cycle ;lcd_hspw: hsync plus width ;lcd_vspw: vysnc plus width ;lcd_edp_tx_ic 0:anx9804; 1:anx6345 ;lcd_edp_tx_rate 1:1.62G; 2:2.7G; 3:5.4G ;lcd_edp_tx_lane 1/2/4lane ;lcd_edp_colordepth 0:8bit; 1:6bit ;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither ;lcd_gamma_en lcd gamma correction enable ;lcd_bright_curve_en lcd bright curve correction enable ;lcd_cmap_en lcd color map function enable ;lcd_gpio_scl: iic SCL ;lcd_gpio_sda iic SDA ;lcd_gpio_0/1/2/3 lcd gpio ;deu_mode 0:smoll lcd screen; 1:large lcd screen(larger than 10inch) ;lcdgamma4iep: Smart Backlight parameter, lcd gamma vale * 10; ; decrease it while lcd is not bright enough; increase while lcd is too bright ;smart_color 90:normal lcd screen 65:retina lcd screen(9.7inch) ;---------------------------------------------------------------------------------- [lcd0_para] lcd_used = 0 lcd_if = 3 ;lcd_driver_name = "default_lcd" ;lcd_x = 800 ;lcd_y = 480 ;lcd_width = 162 ;lcd_height = 121 ;lcd_size = "8.0" ;lcd_model_name = "CHIMEI HJ080IA-01B" ;lcd_dclk_freq = 33 ;lcd_x = 1920 ;lcd_y = 1080 ;lcd_width = 406 ;lcd_height = 228 ;lcd_size = "20.0" ;lcd_model_name = "virtual" ;lcd_dclk_freq = 138 lcd_x = 960 lcd_y = 540 lcd_width = 203 lcd_height = 114 lcd_size = "10.0" lcd_model_name = "virtual" lcd_dclk_freq = 41 lcd_pwm_freq = 50000 lcd_pwm_pol = 1 lcd_pwm_max_limit = 150 ;lcd_hbp = 46 ;lcd_ht = 928 ;lcd_hspw = 0 ;lcd_vbp = 23 ;lcd_vt = 525 ;lcd_vspw = 0 ;lcd_hbp = 32 ;lcd_ht = 2000 ;lcd_hspw = 0 ;lcd_vbp = 5 ;lcd_vt = 1111 ;lcd_vspw = 0 lcd_hbp = 32 lcd_ht = 1216 lcd_hspw = 0 lcd_vbp = 3 lcd_vt = 562 lcd_vspw = 0 lcd_lvds_if = 0 lcd_lvds_colordepth = 1 lcd_lvds_mode = 0 lcd_frm = 1 lcd_gamma_en = 0 lcd_bright_curve_en = 1 lcd_cmap_en = 0 deu_mode = 0 lcdgamma4iep = 22 smartbl_low_limit = 85 smart_color = 90 ;lcd_bl_en = port:PH27<1><1> ;lcd_power = port:PC27<1><1> ;lcd_pwm = port:PH13<2><0> ;lcdd0 = port:PD00<2><0><3> ;lcdd1 = port:PD01<2><0><3> ;lcdd2 = port:PD02<2><0><3> ;lcdd3 = port:PD03<2><0><3> ;lcdd4 = port:PD04<2><0><3> ;lcdd5 = port:PD05<2><0><3> ;lcdd6 = port:PD06<2><0><3> ;lcdd7 = port:PD07<2><0><3> ;lcdd8 = port:PD08<2><0><3> ;lcdd9 = port:PD09<2><0><3> ;lcdd10 = port:PD10<2><0><3> ;lcdd11 = port:PD11<2><0><3> ;lcdd12 = port:PD12<2><0><3> ;lcdd13 = port:PD13<2><0><3> ;lcdd14 = port:PD14<2><0><3> ;lcdd15 = port:PD15<2><0><3> ;lcdd16 = port:PD16<2><0><3> ;lcdd17 = port:PD17<2><0><3> ;lcdd18 = port:PD18<2><0><3> ;lcdd19 = port:PD19<2><0><3> ;lcdd20 = port:PD20<2><0><3> ;lcdd21 = port:PD21<2><0><3> ;lcdd22 = port:PD22<2><0><3> ;lcdd23 = port:PD23<2><0><3> ;lcdclk = port:PD24<2><0><3> ;lcdde = port:PD25<2><0><3> ;lcdhsync = port:PD26<2><0><3> ;lcdvsync = port:PD27<2><0><3> ;---------------------------------------------------------------------------------- ;hdmi configuration ;---------------------------------------------------------------------------------- [hdmi_para] hdmi_used = 1 ;-------------------------------------------------------------------------------- ;vip (video input port) configuration ;vip_used: 0:disable 1:enable ;vip_mode: 0:sample one interface to one buffer 1:sample two interface to one buffer ;vip_dev_qty: The quantity of devices linked to capture bus ;vip_dev(x)_isp_used 0:not use isp 1:use isp ;vip_dev(x)_fmt: 0:yuv 1:bayer raw rgb ;vip_dev(x)_stby_mode: 0:not shut down power at standby 1:shut down power at standby ;vip_dev(x)_vflip: flip in vertical direction 0:disable 1:enable ;vip_dev(x)_hflip: flip in horizontal direction 0:disable 1:enable ;vip_dev(x)_iovdd: camera module io power handle string, pmu power supply ;vip_dev(x)_iovdd_vol: camera module io power voltage, pmu power supply ;vip_dev(x)_avdd: camera module analog power handle string, pmu power supply ;vip_dev(x)_avdd_vol: camera module analog power voltage, pmu power supply ;vip_dev(x)_dvdd: camera module core power handle string, pmu power supply ;vip_dev(x)_dvdd_vol: camera module core power voltage, pmu power supply ;vip_dev(x)_afvdd: camera module vcm power handle string, pmu power supply ;vip_dev(x)_afvdd_vol: camera module vcm power voltage, pmu power supply ;x indicates the index of the devices which are linked to the same capture bus ;fill voltage in uV, e.g. iovdd = 2.8V, vip_devx_iovdd_vol = 2800000 ;fill handle string as below: ;axp22_eldo3 ;axp22_dldo4 ;axp22_eldo2 ;fill handle string "" when not using any pmu power supply ;-------------------------------------------------------------------------------- [vip0_para] vip_used = 0 vip_mode = 0 vip_dev_qty = 1 vip_vip_mck = port:PE16<2> vip_dev0_mname = "" vip_dev0_lane = 2 vip_dev0_twi_id = 0 vip_dev0_twi_addr = 0x6c vip_dev0_isp_used = 1 vip_dev0_fmt = 1 vip_dev0_stby_mode = 0 vip_dev0_vflip = 0 vip_dev0_hflip = 0 vip_dev0_iovdd = "axp22_dldo3" vip_dev0_iovdd_vol = 2800000 vip_dev0_avdd = "axp22_ldoio0" vip_dev0_avdd_vol = 2800000 vip_dev0_dvdd = "axp22_eldo2" vip_dev0_dvdd_vol = 1500000 vip_dev0_afvdd = "" vip_dev0_afvdd_vol = 2800000 vip_dev0_power_en = vip_dev0_reset = vip_dev0_pwdn = vip_dev0_flash_en = vip_dev0_flash_mode = vip_dev0_af_pwdn = vip_dev0_act_used = 1 vip_dev0_act_name = "ad5820_act" vip_dev0_act_slave = 0x18 vip_dev1_mname = "" vip_dev1_lane = 1 vip_dev1_twi_id = 0 vip_dev1_twi_addr = vip_dev1_isp_used = 0 vip_dev1_fmt = 1 vip_dev1_stby_mode = 0 vip_dev1_vflip = 0 vip_dev1_hflip = 0 vip_dev1_iovdd = "axp22_dldo3" vip_dev1_iovdd_vol = 2800000 vip_dev1_avdd = "axp22_ldoio0" vip_dev1_avdd_vol = 2800000 vip_dev1_dvdd = "axp22_eldo2" vip_dev1_dvdd_vol = 1800000 vip_dev1_afvdd = "" vip_dev1_afvdd_vol = 2800000 vip_dev1_power_en = vip_dev1_reset = vip_dev1_pwdn = vip_dev1_flash_en = vip_dev1_flash_mode = vip_dev1_af_pwdn = [vip1_para] vip_used = 0 vip_mode = 0 vip_dev_qty = 1 vip_csi_pck = port:PE00<2> vip_csi_mck = port:PE01<2> vip_csi_hsync = port:PE02<2> vip_csi_vsync = port:PE03<2> vip_csi_d0 = vip_csi_d1 = vip_csi_d2 = vip_csi_d3 = vip_csi_d4 = port:PE08<2> vip_csi_d5 = port:PE09<2> vip_csi_d6 = port:PE10<2> vip_csi_d7 = port:PE11<2> vip_csi_d8 = port:PE12<2> vip_csi_d9 = port:PE13<2> vip_csi_d10 = port:PE14<2> vip_csi_d11 = port:PE15<2>