From f67c298916e8adf42e149dc6fdb53d7f2bdb03b1 Mon Sep 17 00:00:00 2001 From: Andreas Kraschitzer Date: Thu, 28 Jul 2016 16:45:13 +0200 Subject: added fex files for INNOLUX and TOPWAY display Added fex files for following displays: * INNOLUX_AT070TNA2_V.1 * TOPWAY_LMT104SBH01-NNC --- 3.3/displays/INNOLUX_AT070TNA2_V.1.fex | 1676 +++++++++++++++++++++++++++++++ 3.3/displays/TOPWAY_LMT104SBH01-NNC.fex | 977 ++++++++++++++++++ 2 files changed, 2653 insertions(+) create mode 100644 3.3/displays/INNOLUX_AT070TNA2_V.1.fex create mode 100644 3.3/displays/TOPWAY_LMT104SBH01-NNC.fex diff --git a/3.3/displays/INNOLUX_AT070TNA2_V.1.fex b/3.3/displays/INNOLUX_AT070TNA2_V.1.fex new file mode 100644 index 0000000..c9a673e --- /dev/null +++ b/3.3/displays/INNOLUX_AT070TNA2_V.1.fex @@ -0,0 +1,1676 @@ + +; A31 uQseven module + +[product] +version = "301" +machine = "pangolin" + +[platform] +eraseflag = 1 +[fel_key] +fel_key_type = 1 + +;---------------------------------------------------------------------------------- +; system configuration +; ? +;dcdc1_vol ---set dcdc1 voltage,mV,1600-3400,100mV/step +;dcdc2_vol ---set dcdc2 voltage,mV,600-1540,20mV/step +;dcdc3_vol ---set dcdc3 voltage,mV,600-1860,20mV/step +;dcdc4_vol ---set dcdc4 voltage,mV,600-1540,20mV/step +;dcdc5_vol ---set dcdc5 voltage,mV,1000-2550,50mV/step +;aldo2_vol ---set aldo2 voltage,mV,700-3300,100mV/step +;aldo3_vol ---set aldo3 voltage,mV,700-3300,100mV/step +;---------------------------------------------------------------------------------- + +; power_start meaning +; +; @ 0: Do not allow direct power plug adapters must pass judgment: to +; meet the following conditions Direct Power On: Long press power +; button, the previous system status is, if the battery is low, you +; can not boot +; @ 1: in any state, allowing direct plug adapters power while +; requiring high enough battery power +; @ 2: Do not allow direct power plug adapters must pass judgment: to +; meet the following conditions Direct Power On: Long press power +; button, the previous system status is not required to battery power +; @ 3: any state that allows direct power plug adapters do not require +; battery power + +[target] +boot_clock = 1008 +storage_type = -1 +power_start = 3 + +[power_sply] +dcdc1_vol = 3300 +dcdc2_vol = 1200 +dcdc3_vol = 1260 +dcdc4_vol = 1260 +;dcdc4_vol = 1100 +dcdc5_vol = 1500 +aldo1_vol = 0 +aldo2_vol = 1800 +aldo3_vol = 3000 +eldo1_vol = 0 +eldo2_vol = 0 +eldo3_vol = 0 + +[card_boot] +logical_start = 40960 +sprite_gpio0 = + +;--------------------------------------------------------------------------------------------------------- +; if 1 == standby_mode, then support super standby; +; else, support normal standby. +;--------------------------------------------------------------------------------------------------------- +[pm_para] +standby_mode = 0 +dram_selfresh_en = 0 + +[card0_boot_para] +card_ctrl = 0 +card_high_speed = 1 +card_line = 4 +sdc_d1 = port:PF0<2><1> +sdc_d0 = port:PF1<2><1> +sdc_clk = port:PF2<2><1> +sdc_cmd = port:PF3<2><1> +sdc_d3 = port:PF4<2><1> +sdc_d2 = port:PF5<2><1> + +;[card2_boot_para] +;card_ctrl = 2 +;card_high_speed = 1 +;card_line = 8 +;sdc_clk = port:PC07<3><1><2> +;sdc_cmd = port:PC06<3><1><2> +;sdc_d0 = port:PC08<3><1><2> +;sdc_d1 = port:PC09<3><1><2> +;sdc_d2 = port:PC10<3><1><2> +;sdc_d3 = port:PC11<3><1><2> +;sdc_d4 = port:PC12<3><1><2> +;sdc_d5 = port:PC13<3><1><2> +;sdc_d6 = port:PC14<3><1><2> +;sdc_d7 = port:PC15<3><1><2> + +[twi_para] +twi_port = 0 +twi_scl = port:PH14<2> +twi_sda = port:PH15<2> + +[uart_para] +;uart_debug_port = 2 +;uart_debug_tx = port:PG06<2><1> +;uart_debug_rx = port:PG07<2><1> +uart_debug_port = 0 +uart_debug_tx = port:PH20<2><1> +uart_debug_rx = port:PH21<2><1> + +[jtag_para] +jtag_enable = 1 +jtag_ms = port:PH9<3> +jtag_ck = port:PH10<3> +jtag_do = port:PH11<3> +jtag_di = port:PH12<3> + +[clock] +pll3 = 297 +pll4 = 300 +pll6 = 600 +pll7 = 297 +pll8 = 360 +pll9 = 297 +pll10 = 702 + +;***************************************************************************** +;sdram configuration +; +;***************************************************************************** +;[dram_para] +;dram_clk = 360 +;dram_type = 3 +;dram_zq = 0x46 +;;;dram_clk = 624 +;;;dram_type = 3 +;;;dram_zq = 0xbb +;dram_odt_en = 0 +;dram_para1 = 0x10e20400 +;dram_para2 = 0x1101 +;dram_mr0 = 0x1a50 +;dram_mr1 = 0x04 +;dram_mr2 = 0x18 +;dram_mr3 = 0 +;dram_tpr0 = 0 +;dram_tpr1 = 0x80000800 +;dram_tpr2 = 0x39a70140 +;dram_tpr3 = 0xa092e74c +;dram_tpr4 = 0x2948c209 +;dram_tpr5 = 0x8944422c +;;;;dram_tpr6 = 0x30028480 +;dram_tpr6 = 0x300284a0 +;dram_tpr7 = 0x2a3297 +;dram_tpr8 = 0x5034fa8 +;dram_tpr9 = 0x36353d8 +;dram_tpr10 = 0 +;dram_tpr11 = 0 +;dram_tpr12 = 0 +;dram_tpr13 = 0 + +[dram_para] +dram_clk = 480 +dram_type = 3 +dram_zq = 0x46 +dram_odt_en = 1 +dram_para1 = 0x10e20400 +dram_para2 = 0x1101 +dram_mr0 = 0x1640 +dram_mr1 = 0x0040 +dram_mr2 = 0x0008 +dram_mr3 = 0x0000 +dram_tpr0 = 0 +dram_tpr1 = 0x80000400 +dram_tpr2 = 0x3ea70140 +dram_tpr3 = 0xa08b063c +dram_tpr4 = 0x2946c208 +dram_tpr5 = 0x67443a23 +dram_tpr6 = 0x30028580 +dram_tpr7 = 0x002a3297 +dram_tpr8 = 0x05034fa8 +dram_tpr9 = 0x036353d8 +dram_tpr10 = 0 +dram_tpr11 = 0 +dram_tpr12 = 0 +dram_tpr13 = 0 + +;---------------------------------------------------------------------------------- +;os life cycle para configuration +;---------------------------------------------------------------------------------- + +;------------------------------------------------------------------------------; +; 10/100/100Mbps Ethernet MAC Controller Configure ; +;------------------------------------------------------------------------------; +; 配置选项： ; +; gmac_used --- 1: gmac used, 0: not used ; +;------------------------------------------------------------------------------; +; MII GMII RGMII MII GMII RGMII MII GMII RGMII ; +;PA00~03 * * * PA10 * * PA20 * * * ; +; PA04 * PA11~14 * * * PA21 * * ; +; PA05 * PA15 * PA22 * * ; +; PA06 * PA16 * PA23 * * ; +; PA07 * PA17 * PA24 * * ; +; PA08 * * PA18 * PA25 * * ; +; PA09 * * * PA19 * * * PA26~27 * * * ; +;------------------------------------------------------------------------------; +[gmac_para] +gmac_used = 1 +gmac_txd0 = port:PA00<2><3> +gmac_txd1 = port:PA01<2><3> +gmac_txd2 = port:PA02<2><3> +gmac_txd3 = port:PA03<2><3> +gmac_txclk = port:PA10<2><3> +gmac_txen = port:PA09<2><3> +;gmac_gtxclk = port:PA10<2><3> +gmac_rxd0 = port:PA11<2><3> +gmac_rxd1 = port:PA12<2><3> +gmac_rxd2 = port:PA13<2><3> +gmac_rxd3 = port:PA14<2><3> +gmac_rxdv = port:PA19<2><3> +gmac_rxclk = port:PA20<2><3> +;gmac_txerr = port:PA21<2><3> +;gmac_rxerr = port:PA22<2><3> +;gmac_col = port:PA23<2><3> +;gmac_crs = port:PA24<2><3> +gmac_clkin = port:PA25<2><3> +gmac_mdc = port:PA26<2><1><3> +gmac_mdio = port:PA27<2><1><3> +;gmac_phy_reset = port:PA07<1><3><1> +;usb_hub_reset = port:PC21<1><3><1> + +;---------------------------------------------------------------------------------- +;i2c configuration +;---------------------------------------------------------------------------------- +[twi0_para] +twi_used = 1 +twi_scl = port:PH14<2> +twi_sda = port:PH15<2> + +[twi1_para] +twi_used = 1 +twi_scl = port:PH16<2> +twi_sda = port:PH17<2> + +[twi2_para] +twi_used = 1 +twi_scl = port:PH18<2> +twi_sda = port:PH19<2> + +[twi3_para] +twi_used = 1 +twi_scl = port:PB05<4> +twi_sda = port:PB06<4> + +;---------------------------------------------------------------------------------- +;uart configuration +;uart_type --- 2 (2 wire), 4 (4 wire), 8 (8 wire, full function) +;---------------------------------------------------------------------------------- + +; UART0 (PH20/PH21): test points +[uart_para0] +uart_used = 1 +uart_port = 0 +uart_type = 2 +uart_tx = port:PH20<2><1> +uart_rx = port:PH21<2><1> + +; UART1 (PA4/PA5): STM32 +[uart_para1] +uart_used = 1 +uart_port = 1 +uart_type = 2 +uart_tx = port:PA04<4><1> +uart_rx = port:PA05<4><1> + +; UART2 (PG6-PG9): base-board +[uart_para2] +uart_used = 1 +uart_port = 2 +uart_type = 4 +uart_tx = port:PG06<2><1> +uart_rx = port:PG07<2><1> +uart_rts = port:PG08<2><1> +uart_cts = port:PG09<2><1> + +[uart_para3] +uart_used = 0 +uart_port = 3 +uart_type = 4 +uart_tx = port:PB05<3><1> +uart_rx = port:PB06<3><1> +uart_rts = port:PB04<3><1> +uart_cts = port:PB00<3><1> + +[uart_para4] +uart_used = 0 +uart_port = 4 +uart_type = 2 +uart_tx = port:PG17<2><1> +uart_rx = port:PG18<2><1> +uart_rts = port:PB04<3><1> +uart_cts = port:PB00<3><1> + +[uart_para5] +uart_used = 0 +uart_port = 5 +uart_type = 4 +uart_tx = port:PE04<3><1> +uart_rx = port:PE05<3><1> +uart_rts = port:PE06<3><1> +uart_cts = port:PE07<3><1> + +;---------------------------------------------------------------------------------- +;spi configuration +;---------------------------------------------------------------------------------- +[spi0_para] +spi_used = 0 +spi_cs_bitmap = 1 +spi_cs0 = port:PC27<3><1> +spi_sclk = port:PC02<3> +spi_mosi = port:PC00<3> +spi_miso = port:PC01<3> + +[spi1_para] +spi_used = 1 +spi_cs_bitmap = 3 +spi_cs1 = port:PG12<2><1> +spi_cs0 = port:PG13<2><1> +spi_sclk = port:PG14<2> +spi_mosi = port:PG15<2> +spi_miso = port:PG16<2> + +[spi2_para] +spi_used = 0 +spi_cs_bitmap = 1 +spi_cs0 = port:PH09<2> +spi_sclk = port:PH10<2> +spi_mosi = port:PH11<2> +spi_miso = port:PH12<2> + +[spi3_para] +spi_used = 0 +spi_cs_bitmap = 1 +spi_cs0 = port:PA21<4> +spi_sclk = port:PA22<4> +spi_mosi = port:PA23<4> +spi_miso = port:PA24<4> +spi_cs1 = port:PA25<4> + +;---------------------------------------------------------------------------------- +;resistance tp configuration +;---------------------------------------------------------------------------------- +[rtp_para] +rtp_used = 0 +rtp_screen_size = 5 +rtp_regidity_level = 5 +rtp_press_threshold_enable = 0 +rtp_press_threshold = 0x1f40 +rtp_sensitive_level = 0xf +rtp_exchange_x_y_flag = 0 + +;---------------------------------------------------------------------------------- +;capacitor tp configuration +;external int function +;wakeup output function +;notice --- tp_int_port & tp_io_port use the same port +;---------------------------------------------------------------------------------- +[ctp_para] +ctp_used = 0 +ctp_name = "gsl1680" +ctp_twi_id = 1 +ctp_twi_addr = 0x40 +ctp_screen_max_x = 800 +ctp_screen_max_y = 480 +ctp_revert_x_flag = 0 +ctp_revert_y_flag = 0 +ctp_exchange_x_y_flag = 0 + +#ctp_int_port = port:PA23<6> +#ctp_wakeup = port:PA24<1><3><1> + +#ctp_int_port = port:PG11<6> +#ctp_wakeup = port:PG10<1><3><1> + +;---------------------------------------------------------------------------------- +;touch key configuration +;---------------------------------------------------------------------------------- +[tkey_para] +tkey_used = 0 +tkey_twi_id = +tkey_twi_addr = +tkey_int = + +;---------------------------------------------------------------------------------- +;motor configuration +;---------------------------------------------------------------------------------- +[motor_para] +motor_used = 0 +motor_shake = port:power3<1><1> + +[nand0_para] +nand_support_2ch = 0 + +nand0_used = 0 +good_block_ratio = 944 +nand0_we = port:PC00<2> +nand0_ale = port:PC01<2> +nand0_cle = port:PC02<2> +nand0_ce1 = port:PC03<2> +nand0_ce0 = port:PC04<2> +nand0_nre = port:PC05<2> +nand0_rb0 = port:PC06<2> +nand0_rb1 = port:PC07<2> +nand0_d0 = port:PC08<2> +nand0_d1 = port:PC09<2> +nand0_d2 = port:PC10<2> +nand0_d3 = port:PC11<2> +nand0_d4 = port:PC12<2> +nand0_d5 = port:PC13<2> +nand0_d6 = port:PC14<2> +nand0_d7 = port:PC15<2> +nand0_ce2 = port:PC25<2> +nand0_ce3 = port:PC26<2> +nand0_ndqs = port:PC24<2> + +[nand1_para] +nand1_used = 0 +nand1_we = port:PH00<2> +nand1_ale = port:PH01<2> +nand1_cle = port:PH02<2> +nand1_ce1 = port:PH03<2> +nand1_ce0 = port:PH04<2> +nand1_nre = port:PH05<2> +nand1_rb0 = port:PH06<2> +nand1_rb1 = port:PH07<2> +nand1_d0 = port:PC16<3> +nand1_d1 = port:PC17<3> +nand1_d2 = port:PC18<3> +nand1_d3 = port:PC19<3> +nand1_d4 = port:PC20<3> +nand1_d5 = port:PC21<3> +nand1_d6 = port:PC22<3> +nand1_d7 = port:PC23<3> +nand1_ce2 = port:PH29<2> +nand1_ce3 = port:PH30<2> +nand1_ndqs = port:PH08<2> + +;---------------------------------------------------------------------------------- +;disp init configuration +; +;disp_mode (0:screen0) +;screenx_output_type (0:none; 1:lcd; 3:hdmi;) +;screenx_output_mode (used for hdmi output, 0:480i 1:576i 2:480p 3:576p 4:720p50) +; (5:720p60 6:1080i50 7:1080i60 8:1080p24 9:1080p50 10:1080p60) +;fbx format (4:RGB655 5:RGB565 6:RGB556 7:ARGB1555 8:RGBA5551 9:RGB888 10:ARGB8888 12:ARGB4444) +;fbx pixel sequence (0:ARGB 1:BGRA 2:ABGR 3:RGBA) +;fbx_width,fbx_height (framebuffer horizontal/vertical pixels, fix to output resolution while equal 0) +;lcdx_backlight (lcd init backlight,the range:[0,256],default:197 +;lcdx_yy (lcd init screen bright/contrast/saturation/hue, value:0~100, default:50/50/57/50) +;---------------------------------------------------------------------------------- +[boot_disp] +;output_type = 3 +;output_mode = 9 +;auto_hpd = 1 + +[disp_init] +disp_init_enable = 1 +disp_mode = 2 + +screen0_output_type = 1 +screen0_output_mode = 4 +;screen0_output_mode = 9 + +screen1_output_type = 3 +screen1_output_mode = 9 + +fb0_format = 0 +fb0_pixel_sequence = 0 +fb0_scaler_mode_enable = 0 +fb0_width = 1024 +fb0_height = 600 + +fb1_format = 0 +fb1_pixel_sequence = 0 +fb1_scaler_mode_enable = 0 +fb1_width = 1920 +fb1_height = 1080 + +lcd0_backlight = 200 +lcd1_backlight = 50 + +lcd0_bright = 50 +lcd0_contrast = 50 +lcd0_saturation = 57 +lcd0_hue = 50 + +lcd1_bright = 50 +lcd1_contrast = 50 +lcd1_saturation = 57 +lcd1_hue = 50 + +;---------------------------------------------------------------------------------- +;lcd0 configuration + +;lcd_if: 0:hv(sync+de); 1:8080; 2:ttl; 3:lvds; 4:dsi; 5:edp +;lcd_x: lcd horizontal resolution +;lcd_y: lcd vertical resolution +;lcd_width: width of lcd in mm +;lcd_height: height of lcd in mm +;lcd_size lcd panel size, e.g. "8.0","9.7" +;lcd_model_name lcd panel model name +;lcd_dclk_freq: in MHZ unit +;lcd_pwm_freq: in HZ unit +;lcd_pwm_pol: lcd backlight PWM polarity +;lcd_pwm_max_limit lcd backlight PWM max limit(<=255) +;lcd_hbp: hsync back porch +;lcd_ht: hsync total cycle +;lcd_vbp: vsync back porch +;lcd_vt: vysnc total cycle +;lcd_hspw: hsync plus width +;lcd_vspw: vysnc plus width +;lcd_edp_tx_ic 0:anx9804; 1:anx6345 +;lcd_edp_tx_rate 1:1.62G; 2:2.7G; 3:5.4G +;lcd_edp_tx_lane 1/2/4lane +;lcd_edp_colordepth 0:8bit; 1:6bit +;lcd_frm: 0:disable; 1:enable rgb666 dither; 2:enable rgb656 dither +;lcd_gamma_en lcd gamma correction enable +;lcd_bright_curve_en lcd bright curve correction enable +;lcd_cmap_en lcd color map function enable +;lcd_gpio_scl: iic SCL +;lcd_gpio_sda iic SDA +;lcd_gpio_0/1/2/3 lcd gpio +;deu_mode 0:smoll lcd screen; 1:large lcd screen(larger than 10inch) +;lcdgamma4iep: Smart Backlight parameter, lcd gamma vale * 10; +; decrease it while lcd is not bright enough; increase while lcd is too bright +;smart_color 90:normal lcd screen 65:retina lcd screen(9.7inch) +;---------------------------------------------------------------------------------- +[lcd0_para] +lcd_used = 1 + +lcd_driver_name = "default_lcd" +lcd_size = "7.08" +lcd_if = 3 +lcd_x = 1024 +lcd_y = 600 +lcd_width = 155 +lcd_height = 90 +lcd_dclk_freq = 51 +lcd_pwm_used = 1 +lcd_pwm_ch = 0 +lcd_pwm_freq = 50000 +lcd_pwm_pol = 0 + +lcd_hbp = 160 +lcd_ht = 1344 +lcd_hspw = 10 +lcd_vbp = 20 +lcd_vt = 635 +lcd_vspw = 3 +lcd_lvds_if = 0 +lcd_lvds_colordepth = 1 +lcd_lvds_mode = 0 +lcd_frm = 1 +lcd_hv_clk_phase = 0 +lcd_hv_sync_polarity = 0 +lcd_gamma_en = 0 +lcd_bright_curve_en = 0 +lcd_cmap_en = 0 + +deu_mode = 0 +lcdgamma4iep = 22 +smartbl_low_limit = 85 +smart_color = 90 + +lcd_bl_en = port:PD20<1><0><1> +lcd_power = port:PD21<1><0><1> +lcd_pwm = port:PH13<2><0> + +lcdd0 = port:PD00<3><0><3> +lcdd1 = port:PD01<3><0><3> +lcdd2 = port:PD02<3><0><3> +lcdd3 = port:PD03<3><0><3> +lcdd4 = port:PD04<3><0><3> +lcdd5 = port:PD05<3><0><3> +lcdd6 = port:PD06<3><0><3> +lcdd7 = port:PD07<3><0><3> +;lcdd8 = port:PD08<2><0><3> +;lcdd9 = port:PD09<2><0><3> +;lcdd10 = port:PD10<2><0><3> +;lcdd11 = port:PD11<2><0><3> +;lcdd12 = port:PD12<2><0><3> +;lcdd13 = port:PD13<2><0><3> +;lcdd14 = port:PD14<2><0><3> +;lcdd15 = port:PD15<2><0><3> +;lcdd16 = port:PD16<2><0><3> +;lcdd17 = port:PD17<2><0><3> +;lcdd18 = port:PD18<2><0><3> +;lcdd19 = port:PD19<2><0><3> +;lcdd20 = port:PD20<2><0><3> +;lcdd21 = port:PD21<2><0><3> +;lcdd22 = port:PD22<2><0><3> +;lcdd23 = port:PD23<2><0><3> +;lcdclk = port:PD24<2><0><3> +;lcdde = port:PD25<2><0><3> +;lcdhsync = port:PD26<2><0><3> +;lcdvsync = port:PD27<2><0><3> + +;---------------------------------------------------------------------------------- +;hdmi configuration +;---------------------------------------------------------------------------------- +[hdmi_para] +hdmi_used = 1 + + + +;-------------------------------------------------------------------------------- +;vip (video input port) configuration +;vip_used: 0:disable 1:enable +;vip_mode: 0:sample one interface to one buffer 1:sample two interface to one buffer +;vip_dev_qty: The quantity of devices linked to capture bus +;vip_dev(x)_isp_used 0:not use isp 1:use isp +;vip_dev(x)_fmt: 0:yuv 1:bayer raw rgb +;vip_dev(x)_stby_mode: 0:not shut down power at standby 1:shut down power at standby +;vip_dev(x)_vflip: flip in vertical direction 0:disable 1:enable +;vip_dev(x)_hflip: flip in horizontal direction 0:disable 1:enable +;vip_dev(x)_iovdd: camera module io power handle string, pmu power supply +;vip_dev(x)_iovdd_vol: camera module io power voltage, pmu power supply +;vip_dev(x)_avdd: camera module analog power handle string, pmu power supply +;vip_dev(x)_avdd_vol: camera module analog power voltage, pmu power supply +;vip_dev(x)_dvdd: camera module core power handle string, pmu power supply +;vip_dev(x)_dvdd_vol: camera module core power voltage, pmu power supply +;vip_dev(x)_afvdd: camera module vcm power handle string, pmu power supply +;vip_dev(x)_afvdd_vol: camera module vcm power voltage, pmu power supply +;x indicates the index of the devices which are linked to the same capture bus +;fill voltage in uV, e.g. iovdd = 2.8V, vip_devx_iovdd_vol = 2800000 +;fill handle string as below: +;axp22_eldo3 +;axp22_dldo4 +;axp22_eldo2 +;fill handle string "" when not using any pmu power supply +;-------------------------------------------------------------------------------- + +[vip0_para] + +vip_used = 0 +vip_mode = 0 +vip_dev_qty = 1 +vip_vip_mck = port:PE16<2> + +vip_dev0_mname = "" +vip_dev0_lane = 2 +vip_dev0_twi_id = 0 +vip_dev0_twi_addr = 0x6c +vip_dev0_isp_used = 1 +vip_dev0_fmt = 1 +vip_dev0_stby_mode = 0 +vip_dev0_vflip = 0 +vip_dev0_hflip = 0 +vip_dev0_iovdd = "axp22_dldo3" +vip_dev0_iovdd_vol = 2800000 +vip_dev0_avdd = "axp22_ldoio0" +vip_dev0_avdd_vol = 2800000 +vip_dev0_dvdd = "axp22_eldo2" +vip_dev0_dvdd_vol = 1500000 +vip_dev0_afvdd = "" +vip_dev0_afvdd_vol = 2800000 +vip_dev0_power_en = +vip_dev0_reset = +vip_dev0_pwdn = +vip_dev0_flash_en = +vip_dev0_flash_mode = +vip_dev0_af_pwdn = + +vip_dev0_act_used = 1 +vip_dev0_act_name = "ad5820_act" +vip_dev0_act_slave = 0x18 + + +vip_dev1_mname = "" +vip_dev1_lane = 1 +vip_dev1_twi_id = 0 +vip_dev1_twi_addr = +vip_dev1_isp_used = 0 +vip_dev1_fmt = 1 +vip_dev1_stby_mode = 0 +vip_dev1_vflip = 0 +vip_dev1_hflip = 0 +vip_dev1_iovdd = "axp22_dldo3" +vip_dev1_iovdd_vol = 2800000 +vip_dev1_avdd = "axp22_ldoio0" +vip_dev1_avdd_vol = 2800000 +vip_dev1_dvdd = "axp22_eldo2" +vip_dev1_dvdd_vol = 1800000 +vip_dev1_afvdd = "" +vip_dev1_afvdd_vol = 2800000 +vip_dev1_power_en = +vip_dev1_reset = +vip_dev1_pwdn = +vip_dev1_flash_en = +vip_dev1_flash_mode = +vip_dev1_af_pwdn = + + + +[vip1_para] + +vip_used = 0 +vip_mode = 0 +vip_dev_qty = 1 +vip_csi_pck = port:PE00<2> +vip_csi_mck = port:PE01<2> +vip_csi_hsync = port:PE02<2> +vip_csi_vsync = port:PE03<2> +vip_csi_d0 = +vip_csi_d1 = +vip_csi_d2 = +vip_csi_d3 = +vip_csi_d4 = port:PE08<2> +vip_csi_d5 = port:PE09<2> +vip_csi_d6 = port:PE10<2> +vip_csi_d7 = port:PE11<2> +vip_csi_d8 = port:PE12<2> +vip_csi_d9 = port:PE13<2> +vip_csi_d10 = port:PE14<2> +vip_csi_d11 = port:PE15<2> + +vip_dev0_mname = "s5k4ec" +vip_dev0_twi_id = 0 +vip_dev0_twi_addr = 0x5a +vip_dev0_isp_used = 0 +vip_dev0_fmt = 0 +vip_dev0_stby_mode = 0 +vip_dev0_vflip = 0 +vip_dev0_hflip = 1 +vip_dev0_iovdd = "axp22_dldo3" +vip_dev0_iovdd_vol = 2800000 +vip_dev0_avdd = "axp22_ldoio0" +vip_dev0_avdd_vol = 2800000 +vip_dev0_dvdd = "axp22_eldo1" +vip_dev0_dvdd_vol = 1500000 +vip_dev0_afvdd = "" +vip_dev0_afvdd_vol = 2800000 +vip_dev0_power_en = port:PE7<1><1> +vip_dev0_reset = port:PG12<1><0> +vip_dev0_pwdn = port:PH28<1><1> +vip_dev0_flash_en = +vip_dev0_flash_mode = +vip_dev0_af_pwdn = + + +vip_dev0_act_used = 0 +vip_dev0_act_name = "" +vip_dev0_act_slave = 0x5a + + +vip_dev1_mname = "" +vip_dev1_twi_id = 0 +vip_dev1_twi_addr = 0x78 +vip_dev1_stby_mode = 0 +vip_dev1_isp_used = 0 +vip_dev1_fmt = 0 +vip_dev1_vflip = 0 +vip_dev1_hflip = 0 +vip_dev1_iovdd = "axp22_dldo3" +vip_dev1_iovdd_vol = 2800000 +vip_dev1_avdd = "axp22_ldoio0" +vip_dev1_avdd_vol = 2800000 +vip_dev1_dvdd = "axp22_eldo2" +vip_dev1_dvdd_vol = 1800000 +vip_dev1_afvdd = "" +vip_dev1_afvdd_vol = 2800000 +vip_dev1_power_en = +vip_dev1_reset = port:PG12<1><0> +vip_dev1_pwdn = port:PH28<1><1> +vip_dev1_flash_en = +vip_dev1_flash_mode = +vip_dev1_af_pwdn = + + +[camera_list_para] +camera_list_para_used = 0 +ov7670 = 0 +gc0308 = 0 +gt2005 = 0 +hi704 = 0 +sp0838 = 0 +mt9m112 = 0 +mt9m113 = 0 +gc2035 = 0 +ov2655 = 0 +hi253 = 0 +gc0307 = 0 +mt9d112 = 0 +ov5640 = 1 +ov5647 = 0 +gc2015 = 0 +ov2643 = 0 +gc0329 = 0 +gc0309 = 0 +tvp5150 = 0 +s5k4ec = 1 +ov5650_mv9335 = 0 +;siv121d = 0 +tw2866 = 0 +;-------------------------------------------------------------------------------- +;tv configuration +; +;-------------------------------------------------------------------------------- +[tvout_para] +tvout_used = +tvout_channel_num = +tv_en = + +[tvin_para] +tvin_used = +tvin_channel_num = + +;-------------------------------------------------------------------------------- +; SDMMC PINS MAPPING | +; ------------------------------------------------------------------------------| +; Config Guide | +; sdc_used: 1-enable card, 0-disable card | +; sdc_detmode: card detect mode | +; 1-detect card by gpio polling | +; 2-detect card by gpio irq(must use IO with irq function) | +; 3-no detect, always in for boot card | +; 4-manually insert and remove by /proc/driver/sunxi-mmc.x/insert| +; sdc_buswidth: card bus width, 1-1bit, 4-4bit, 8-8bit | +; sdc_use_wp: 1-with write protect IO, 0-no write protect IO | +; sdc_isio: for sdio card | +; sdc_regulator: power control.if card supports UHS-I/DDR and HS200 timing for| +; SD3.0 or eMMC4.5, regulator must be configured. the value is | +; the ldo name of AXP221, eg: sdc_regulator = "axp22_eldo2" | +; other: GPIO Mapping configuration | +; ------------------------------------------------------------------------------| +; Note: | +; 1 if detmode=2, sdc_det's config=6 | +; else if detmode=1, sdc_det's config=0 | +; else sdc_det IO is not necessary | +; 2 if the customer wants to support UHS-I and HS200 features, he must provide| +; an independent power supply for the card. This is only used in platforms | +; that supports SD3.0 cards and eMMC4.4+ flashes | +;-------------------------------------------------------------------------------- +[mmc0_para] +sdc_used = 1 +sdc_detmode = 1 +sdc_buswidth = 4 +sdc_clk = port:PF02<2><1><2> +sdc_cmd = port:PF03<2><1><2> +sdc_d0 = port:PF01<2><1><2> +sdc_d1 = port:PF00<2><1><2> +sdc_d2 = port:PF05<2><1><2> +sdc_d3 = port:PF04<2><1><2> +sdc_det = port:PC19<0><1><2> +sdc_use_wp = 0 +sdc_wp = port:PC18<0><1><1> +sdc_isio = 0 +sdc_regulator = "none" + +[mmc1_para] +sdc_used = 0 +sdc_detmode = 4 +sdc_buswidth = 4 +sdc_clk = port:PG00<2><1><2> +sdc_cmd = port:PG01<2><1><2> +sdc_d0 = port:PG02<2><1><2> +sdc_d1 = port:PG03<2><1><2> +sdc_d2 = port:PG04<2><1><2> +sdc_d3 = port:PG05<2><1><2> +sdc_det = +sdc_use_wp = 0 +sdc_wp = +sdc_isio = 1 +sdc_regulator = "none" + +[mmc2_para] +sdc_used = 1 +sdc_detmode = 3 +sdc_buswidth = 8 +sdc_clk = port:PC07<3><1><2> +sdc_cmd = port:PC06<3><1><2> +sdc_d0 = port:PC08<3><1><2> +sdc_d1 = port:PC09<3><1><2> +sdc_d2 = port:PC10<3><1><2> +sdc_d3 = port:PC11<3><1><2> +sdc_d4 = port:PC12<3><1><2> +sdc_d5 = port:PC13<3><1><2> +sdc_d6 = port:PC14<3><1><2> +sdc_d7 = port:PC15<3><1><2> +emmc_rst = port:PC24<3><1><2> +sdc_det = +sdc_use_wp = 0 +sdc_wp = +sdc_isio = 0 +sdc_regulator = "none" + +[mmc3_para] +sdc_used = 0 +sdc_detmode = 2 +sdc_buswidth = 4 +sdc_clk = port:PA10<2><1><2> +sdc_cmd = port:PA09<2><1><2> +sdc_d0 = port:PA11<2><1><2> +sdc_d1 = port:PA12<2><1><2> +sdc_d2 = port:PA13<2><1><2> +sdc_d3 = port:PA14<2><1><2> +sdc_det = +sdc_use_wp = 0 +sdc_wp = +sdc_isio = 0 +sdc_regulator = "none" + +; ------------------------------------------------------------------------------| +; sim card configuration +;-------------------------------------------------------------------------------- +[smc_para] +smc_used = +smc_rst = +smc_vppen = +smc_vppp = +smc_det = +smc_vccen = +smc_sck = +smc_sda = + + +;-------------------------------- +;[usbc0]：控制器0的配置。 +;usb_used：USB使能标志。置1，表示系统中USB模块可用,置0,则表示系统USB禁用。 +;usb_port_type：USB端口的使用情况。 0：device only;1：host only;2：OTG +;usb_detect_type：USB端口的检查方式。0：不做检测;1：vbus/id检查;2：id/dpdm检查 +;usb_id_gpio：USB ID pin脚配置。具体请参考gpio配置说明。 +;usb_det_vbus_gpio：USB DET_VBUS pin脚配置。具体请参考gpio配置说明。 +;usb_drv_vbus_gpio：USB DRY_VBUS pin脚配置。具体请参考gpio配置说明。 +;usb_det_vbus_gpio: "axp_ctrl",表示axp 提供 +;usb_restrict_gpio usb限流控制pin +;usb_restric_flag: usb限流标置 +;-------------------------------- +;-------------------------------- +;--- USB0控制标志 +;-------------------------------- +[usbc0] +usb_used = 1 +usb_port_type = 2 +usb_detect_type = 1 +usb_id_gpio = port:PH2<0><1> +usb_det_vbus_gpio = port:PD23<0><0> +;port:PA16<0><0> +usb_drv_vbus_gpio = port:PH30<1><0><0> +; usb_drv_vbus_gpio = +;port:PA17<1><0><0> +usb_restrict_gpio = port:PH30<1><0><0> +; usb_restrict_gpio = +;port:PA18<1><0><0> +usb_host_init_state = 0 +usb_restric_flag = 0 +usb_restric_voltage = 3550000 +usb_restric_capacity= 5 +;-------------------------------- +;--- USB1控制标志 +;-------------------------------- +[usbc1] +usb_used = 1 +usb_port_type = 1 +usb_detect_type = 0 +usb_id_gpio = +usb_det_vbus_gpio = +usb_drv_vbus_gpio = +usb_restrict_gpio = +usb_host_init_state = 1 +usb_restric_flag = 0 +usb_not_suspend = 0 + +;-------------------------------- +;--- USB2控制标志 +;-------------------------------- +[usbc2] +usb_used = 1 +usb_port_type = 1 +usb_detect_type = 0 +usb_id_gpio = +usb_det_vbus_gpio = +usb_drv_vbus_gpio = +;port:PH24<1><0><0> +usb_restrict_gpio = +usb_host_init_state = 1 +usb_restric_flag = 0 +usb_not_suspend = 0 + +[usbc3] +usb_used = 1 +usb_port_type = 1 +usb_detect_type = 0 +usb_host_init_state = 1 +usb_restric_flag = 0 +usb_not_suspend = 0 + +;-------------------------------- +;--- USB Device +;-------------------------------- +[usb_feature] +vendor_id = 0x18D1 +mass_storage_id = 0x0001 +adb_id = 0x0002 + +manufacturer_name = "USB Developer" +product_name = "Android" +serial_number = "12345678" + +[fastboot_feature] +manufacturer_name = "Theobroma Systems" +product_name = "A31-uQ7" + +[serial_feature] +serial_unique = "1" + +[msc_feature] +vendor_name = "USB 2.0" +product_name = "USB Flash Driver" +release = 100 +luns = 3 + +;-------------------------------------------------------------------------------- +; G sensor configuration +; gs_twi_id --- TWI ID for controlling Gsensor (0: TWI0, 1: TWI1, 2: TWI2) +;-------------------------------------------------------------------------------- +[gsensor_para] +gsensor_used = 0 +gsensor_twi_id = 2 +gsensor_twi_addr = 0x18 +gsensor_int1 = port:PA09<6><1> +gsensor_int2 = + +;hanbiao 20130103 add start +;-------------------------------------------------------------------------------- +; ch7026 configuration +; ch_twi_id --- TWI ID for controlling Gsensor (0: TWI0, 1: TWI1, 2: TWI2) +;-------------------------------------------------------------------------------- +[vga_para] +vga_used = 0 +vga_en = port:PH25<1><1> + + + +;-------------------------------------------------------------------------------- +; sn7325 configuration +; tw_twi_id --- TWI ID for controlling Gsensor (0: TWI0, 1: TWI1, 2: TWI2) +;-------------------------------------------------------------------------------- +[sn7325_para] +sn7325_used = 0 +sn7325_twi_id = 2 +sn7325_twi_addr = 0x58 + +;hanbiao 20130103 add end + +;-------------------------------------------------------------------------------- +; gps gpio configuration +; gps_spi_id --- the index of SPI controller. 0: SPI0, 1: SPI1, 2: SPI2, 15: no SPI used +; gps_spi_cs_num --- the chip select number of SPI controller. 0: SPI CS0, 1: SPI CS1 +; gps_lradc --- the lradc number for GPS used. 0 and 1 is valid, set 2 if not use lradc +;-------------------------------------------------------------------------------- +[gps_para] + +;-------------------------------------------------------------------------------- +;wifi configuration +;wifi_sdc_id --- 0- SDC0, 1- SDC1, 2- SDC2, 3- SDC3 +;wifi_usbc_id --- 0- USB0, 1- USB1, 2- USB2 +;wifi_usbc_type -- 1- EHCI(speed 2.0), 2- OHCI(speed 1.0) +;wifi_mod_sel --- 0- none, 1- ap6181, 2- ap6210(wifi+bt), +; 3 - rtl8723as(wifi+bt), 4- rtl8189es(SM89E00), +; 5 - rtl8192cu, 6 - rtl8188eu, 7 - mt6620, +; 8 - rtl8723au, 9 - ap6330(wifi+bt+fm) +;-------------------------------------------------------------------------------- +[wifi_para] +wifi_used = 1 +wifi_sdc_id = 1 +wifi_usbc_id = 1 +wifi_usbc_type = 1 +wifi_mod_sel = 6 +wifi_power = "axp22_aldo1" + +; 1 - bcm40181 sdio wifi gpio config +;bcm40181_shdn = port:PH09<1><0> +;bcm40181_host_wake = port:PH10<0><0> + +; 2 - bcm40183 sdio wifi gpio config +;bcm40183_wl_regon = port:PH09<1><0> +;bcm40183_wl_host_wake = port:PH10<0><0> +;bcm40183_bt_rst = port:PB05<1><0> +;bcm40183_bt_regon = port:PB05<1><0> +;bcm40183_bt_wake = port:PI20<1><0> +;bcm40183_bt_host_wake = port:PI21<0><0> + +; 3 - rtl8723as sdio wifi + bt gpio config +;rtk_rtl8723as_wl_dis = port:PH09<1><0> +;rtk_rtl8723as_bt_dis = port:PB05<1><0> +;rtk_rtl8723as_wl_host_wake = port:PH10<0><0> +;rtk_rtl8723as_bt_host_wake = port:PI21<0><0> + +; 4 - rtl8189es sdio wifi gpio config +;rtl8189es_shdn = port:PH09<1><0> +;rtl8189es_wakeup = port:PH10<1><1> +; 5 - rtl8192cu usb wifi +; 6 - rtl8188eu usb wifi +; 7 - ap6210 sdio wifi + bt gpio config +ap6xxx_wl_regon = port:PG10<1><0> +ap6xxx_wl_host_wake = port:PG11<0><0> +ap6xxx_bt_regon = port:PL08<1><0> +ap6xxx_bt_wake = port:PL07<1><0> +ap6xxx_bt_host_wake = port:PL06<0><0> +; 8 - ap6330 sdio wifi + bt gpio config +;ap6xxx_wl_regon = port:PM00<1><0> +;ap6xxx_wl_host_wake = port:PM01<0><0> +;ap6xxx_bt_regon = port:PM03<1><0> +;ap6xxx_bt_wake = port:PG12<1><0> +;ap6xxx_bt_host_wake = port:PM04<0><0> + +;-------------------------------------------------------------------------------- +;3G configuration +;-------------------------------------------------------------------------------- +;[3g_para] +;3g_used = 1 +;3g_usbc_num = +;3g_usbc_type = +;3g_uart_num = 3 +;bb_name = "em55" +;bb_vbat = port:PL03<1><0> +;bb_on = port:PM01<1><0> +;bb_pwr_on = port:PM03<1><0> +;bb_wake = port:PM04<1><1> +;bb_rf_dis = port:PM05<1><0> +;bb_rst = port:PM06<1><0> +;bb_dldo = +;bb_dldo_min_uV = +;bb_dldo_max_uV = + + +[3g_para] +3g_used = 0 +3g_usbc_num = 2 +;3g_usbc_type = 2 +3g_uart_num = 0 +bb_name = "cwm600" +bb_vbat = port:PA22<1><0> +;bb_on = port:PM01<1><0> +bb_pwr_on = port:PM01<1><0> +bb_wake = port:PM02<1><1> +;bb_rf_dis = port:PM05<1><0> +bb_rst = port:PM03<1><0> +bb_dldo = +bb_dldo_min_uV = +bb_dldo_max_uV = + + +;[3g_para] +;3g_used = 1 +;3g_usbc_num = 2 +;3g_usbc_type = 2 +;3g_uart_num = +;bb_name = "wm5608" +;bb_vbat = +;bb_on = +;bb_pwr_on = port:PM03<1><1> +;bb_wake = port:PM04<1><1> +;bb_rf_dis = +;bb_rst = port:PM06<1><1> +;bb_dldo = +;bb_dldo_min_uV = +;bb_dldo_max_uV = + +;-------------------------------------------------------------------------------- +;gyroscope +;-------------------------------------------------------------------------------- +[gy_para] +gy_used = 0 +gy_twi_id = 2 +gy_twi_addr = 0x6a +gy_int1 = port:PA10<6><1> +gy_int2 = + +;-------------------------------------------------------------------------------- +;light sensor +;-------------------------------------------------------------------------------- +[ls_para] +ls_used = 0 +ls_twi_id = 2 +ls_twi_addr = 0x23 +ls_int = port:PA12<6><1> + +;-------------------------------------------------------------------------------- +;compass +;-------------------------------------------------------------------------------- +[compass_para] +compass_used = 0 +compass_twi_id = 2 +compass_twi_addr = 0x0d +compass_int = port:PA11<6><1> + +;-------------------------------------------------------------------------------- +;blue tooth +;bt_used ---- blue tooth used (0- no used, 1- used) +;bt_uard_id ---- uart index +;-------------------------------------------------------------------------------- +[bt_para] +bt_used = 0 +bt_uart_id = 2 +bt_wakeup = +bt_gpio = +bt_rst = + +;-------------------------------------------------------------------------------- +;i2s_master:1: SND_SOC_DAIFMT_CBM_CFM(codec clk & FRM master) use +; 2: SND_SOC_DAIFMT_CBS_CFM(codec clk slave & FRM master) not use +; 3: SND_SOC_DAIFMT_CBM_CFS(codec clk master & frame slave) not use +; 4: SND_SOC_DAIFMT_CBS_CFS(codec clk & FRM slave) use +;i2s_select:0 is pcm.1 is i2s +;audio_format: 1:SND_SOC_DAIFMT_I2S(standard i2s format). use +; 2:SND_SOC_DAIFMT_RIGHT_J(right justfied format). +; 3:SND_SOC_DAIFMT_LEFT_J(left justfied format) +; 4:SND_SOC_DAIFMT_DSP_A(pcm. MSB is available on 2nd BCLK rising edge after LRC rising edge). use +; 5:SND_SOC_DAIFMT_DSP_B(pcm. MSB is available on 1nd BCLK rising edge after LRC rising edge) +;signal_inversion:1:SND_SOC_DAIFMT_NB_NF(normal bit clock + frame) use +; 2:SND_SOC_DAIFMT_NB_IF(normal BCLK + inv FRM) +; 3:SND_SOC_DAIFMT_IB_NF(invert BCLK + nor FRM) use +; 4:SND_SOC_DAIFMT_IB_IF(invert BCLK + FRM) +;over_sample_rate: support 128fs/192fs/256fs/384fs/512fs/768fs +;sample_resolution :16bits/20bits/24bits +;word_select_size :16bits/20bits/24bits/32bits +;pcm_sync_period :16/32/64/128/256 +;msb_lsb_first :0: msb first; 1: lsb first +;sign_extend :0: zero pending; 1: sign extend +;slot_index :slot index: 0: the 1st slot - 3: the 4th slot +;slot_width :8 bit width / 16 bit width +;frame_width :0: long frame = 2 clock width; 1: short frame +;tx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law +;rx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law +;-------------------------------------------------------------------------------- +[i2s_para] +i2s_used = 0 +i2s_channel = 2 +i2s_master = 1 +i2s_select = 0 +audio_format = 4 +signal_inversion = 3 +over_sample_rate = 256 +sample_resolution = 16 +word_select_size = 32 +pcm_sync_period = 256 +msb_lsb_first = 0 +sign_extend = 0 +slot_index = 0 +slot_width = 16 +frame_width = 1 +tx_data_mode = 0 +rx_data_mode = 0 +i2s_mclk = +i2s_bclk = port:PB01<2><1> +i2s_lrclk = port:PB02<2><1> +i2s_dout0 = port:PB03<2><1> +i2s_dout1 = +i2s_dout2 = +i2s_dout3 = +i2s_din = port:PB07<2><1> + +;-------------------------------------------------------------------------------- +;pcm_master:1: SND_SOC_DAIFMT_CBM_CFM(codec clk & FRM master) use +; 2: SND_SOC_DAIFMT_CBS_CFM(codec clk slave & FRM master) not use +; 3: SND_SOC_DAIFMT_CBM_CFS(codec clk master & frame slave) not use +; 4: SND_SOC_DAIFMT_CBS_CFS(codec clk & FRM slave) use +;pcm_select:1 is pcm.0 is i2s +;audio_format: 1:SND_SOC_DAIFMT_I2S(standard i2s format). use +; 2:SND_SOC_DAIFMT_RIGHT_J(right justfied format). +; 3:SND_SOC_DAIFMT_LEFT_J(left justfied format) +; 4:SND_SOC_DAIFMT_DSP_A(pcm. MSB is available on 2nd BCLK rising edge after LRC rising edge). use +; 5:SND_SOC_DAIFMT_DSP_B(pcm. MSB is available on 1nd BCLK rising edge after LRC rising edge) +;signal_inversion:1:SND_SOC_DAIFMT_NB_NF(normal bit clock + frame) use +; 2:SND_SOC_DAIFMT_NB_IF(normal BCLK + inv FRM) +; 3:SND_SOC_DAIFMT_IB_NF(invert BCLK + nor FRM) use +; 4:SND_SOC_DAIFMT_IB_IF(invert BCLK + FRM) +;over_sample_rate: support 128fs/192fs/256fs/384fs/512fs/768fs +;sample_resolution :16bits/20bits/24bits +;word_select_size :16bits/20bits/24bits/32bits +;pcm_sync_period :16/32/64/128/256 +;msb_lsb_first :0: msb first; 1: lsb first +;sign_extend :0: zero pending; 1: sign extend +;slot_index :slot index: 0: the 1st slot - 3: the 4th slot +;slot_width :8 bit width / 16 bit width +;frame_width :0: long frame = 2 clock width; 1: short frame +;tx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law +;rx_data_mode :0: 16bit linear PCM; 1: 8bit linear PCM; 2: 8bit u-law; 3: 8bit a-law +;-------------------------------------------------------------------------------- +[pcm_para] +pcm_used = 0 +pcm_channel = 2 +pcm_master = 4 +pcm_select = 1 +audio_format = 4 +signal_inversion = 3 +over_sample_rate = 512 +sample_resolution = 16 +word_select_size = 32 +pcm_sync_period = 64 +msb_lsb_first = 0 +sign_extend = 0 +slot_index = 0 +slot_width = 16 +frame_width = 1 +tx_data_mode = 0 +rx_data_mode = 0 +pcm_mclk = +pcm_bclk = port:PG13<3><1> +pcm_lrclk = port:PG14<3><1> +pcm_dout = port:PG16<3><1> +pcm_din = port:PG15<3><1> + +[spdif_para] +spdif_used = 0 +spdif_dout = port:PH28<3><1> +spdif_din = port:PH27<3><1> + +;-------------------------------------------------------------------------------- +;pa_single_vol,pa_double_vol: 31 level,1.5db/step.0x1f is the large volume. +;cap_vol:use for system record,0x0--0db,0x1--24db,0x2--27db,0x3--30db,0x4--33db,0x5--36db,0x6--39db,0x7--42db +;headphone_vol,earpiece_vol: must least than 0x3b. 0x1 is a step. +;headset_mic_vol: headset mic(mic2) vol,use for phone headset mic call +;main_mic_vol: main mic(mic1) vol,use for phone main mic call +;-------------------------------------------------------------------------------- +[audio_para] +audio_used = 0 +audio_hp_ldo = "none" +headphone_vol = 0x3b +earpiece_vol = 0x3b +cap_vol = 0x5 +pa_single_vol = 0x19 +pa_double_used = 0 +pa_double_vol = 0x1f +headphone_direct_used = 0 +headphone_mute_used = 0 +audio_pa_ctrl = port:PH22<1><0> +audio_mute_ctrl = port:PH23<1><0> +headset_mic_vol = 6 +main_mic_vol = 6 + +;---------------------------------------------------------------------------------- +;ir --- infra remote configuration +;---------------------------------------------------------------------------------- +[ir_para] +ir_used = 0 +ir_rx = port:PL04<2><1> +ir_power_key_code = 0x0 + + +;------------------------------------------------------------------------------------- +;pmu_used ---0:not used,1:used +;pmu_twi_addr ---slave address +;pmu_twi_id ---i2c bus number (0 TWI0, 1 TWI2, 2 TWI3) +;pmu_irq_id ---irq number (0 irq0,1 irq1,……) +;pmu_battery_rdc ---battery initial resistance +;pmu_battery_cap ---battery capability,mAh +;pmu_batdeten ---battery detect en;0:disable 1:enable +;pmu_runtime_chgcur ---set initial charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/ +;pmu_earlysuspend_chgcur ---set earlysuspend charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/ +;pmu_suspend_chgcur ---set suspend charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/ +;pmu_shutdown_chgcur ---set shutdown charging current limite,mA，300/450/600/750/900/1050/1200/1350/1500/1650/1800/1950/ +;pmu_init_chgvol ---set initial charing target voltage,mV,4100/4220/4200/4240 +;pmu_init_chgend_rate ---set initial charing end current rate,10/15 +;pmu_init_chg_enabled ---set initial charing enabled,0:disable,1:enable +;pmu_init_adc_freq ---set initial adc frequency,Hz,100/200/400/800 +;pmu_init_adcts_freq ---set initial adc TS,Hz,100/200/400/800 +;pmu_init_chg_pretime ---set initial pre-charging time,min,40/50/60/70 +;pmu_init_chg_csttime ---set initial constance-charging time,min,360/480/600/720 +;pmu_batt_cap_correct ---correct the battery capacity or not when one charge cycle 0:not correct 1:correct +;pmu_bat_regu_en ---bat regulator is enable or not when charge done 0:disable 1:enable +;pmu_bat_para1 ---battery indication at 3.13V +;pmu_bat_para2 ---battery indication at 3.27V +;pmu_bat_para3 ---battery indication at 3.34V +;pmu_bat_para4 ---battery indication at 3.41V +;pmu_bat_para5 ---battery indication at 3.48V +;pmu_bat_para6 ---battery indication at 3.52V +;pmu_bat_para7 ---battery indication at 3.55V +;pmu_bat_para8 ---battery indication at 3.57V +;pmu_bat_para9 ---battery indication at 3.59V +;pmu_bat_para10 ---battery indication at 3.61V +;pmu_bat_para11 ---battery indication at 3.63V +;pmu_bat_para12 ---battery indication at 3.64V +;pmu_bat_para13 ---battery indication at 3.66V +;pmu_bat_para14 ---battery indication at 3.7V +;pmu_bat_para15 ---battery indication at 3.73V +;pmu_bat_para16 ---battery indication at 3.77V +;pmu_bat_para17 ---battery indication at 3.78V +;pmu_bat_para18 ---battery indication at 3.8V +;pmu_bat_para19 ---battery indication at 3.82V +;pmu_bat_para20 ---battery indication at 3.84V +;pmu_bat_para21 ---battery indication at 3.85V +;pmu_bat_para22 ---battery indication at 3.87V +;pmu_bat_para23 ---battery indication at 3.91V +;pmu_bat_para24 ---battery indication at 3.94V +;pmu_bat_para25 ---battery indication at 3.98V +;pmu_bat_para26 ---battery indication at 4.01V +;pmu_bat_para27 ---battery indication at 4.05V +;pmu_bat_para28 ---battery indication at 4.08V +;pmu_bat_para29 ---battery indication at 4.1V +;pmu_bat_para30 ---battery indication at 4.12V +;pmu_bat_para31 ---battery indication at 4.14V +;pmu_bat_para32 ---battery indication at 4.15V +;pmu_usbvol_limit ---set usb-ac limited voltage enable,1:enable，0：disable +;pmu_usbcur_limit ---set usb-ac limited current enable,1:enable，0：disable +;pmu_usbvol ---set usb-ac limited voltage level,mV,4000/4100/4200/4300/4400/4500/4600/4700,0 - not limite +;pmu_usbcur ---set usb-ac limited current level,mA,500/900, 0 - not limite +;pmu_usbvol_pc ---set usb-pc limited voltage level,mV,4000/4100/4200/4300/4400/4500/4600/4700,0 - not limite +;pmu_usbcur_pc ---set usb-pc limited current level,mA,500/900, 0 - not limite +;pmu_pwroff_vol ---set protect voltage when system start up,mV,2600/2700/2800/2900/3000/3100/3200/3300 +;pmu_pwron_vol ---set protect voltage after system start up,mV,2600/2700/2800/2900/3000/3100/3200/3300 +;pmu_pekoff_time ---set pek off time,ms, 4000/6000/8000/10000 +;pmu_pekoff_func ---set pek off func, 0:shutdown,1:restart +;pmu_pekoff_en ---set pek offlevel powerdown or not, 0:not powerdown,1:powerdown +;pmu_peklong_time ---set pek pek long irq time,ms,1000/1500/2000/2500 +;pmu_pekon_time ---set pek on time,ms,128/1000/2000/3000 +;pmu_pwrok_time ---set pmu pwrok delay time,ms,8/16/32/64 +;pmu_battery_warning_level1 ---low power warning high level,5%-20%,1%/step +;pmu_battery_warning_level2 ---low power warning low level,0%-15%,1%/step +;pmu_restvol_time ---battery indicaton reflash time,30/60/120/ +;pmu_ocv_cou_adjust_time ---ocv battery indication reflash time,60/120/30 +;pmu_chgled_func ---CHGKED pin control，0:controlled by pmu,1:controlled by Charger +;pmu_chgled_type ---CHGLED Type select when pmu_chgled_func=0,0:Type A，1：Type B +;pmu_vbusen_func ---N_VBUSEN function select,0:as an output,1:as an input +;pmu_reset ---when power key press longer than 16's,PMU reset or not.0:not reset 1:reset +;pmu_IRQ_wakeup ---press IRQ wakeup or not when sleep or power down.0:not wakeup 1:wakeup +;pmu_hot_shutdowm ---when PMU over temperature protect or not;0:disable 1:enable +;pmu_inshort ---ACIN and VBUS inshort or not by software;0:auto detect 1:inshort +;pmu_fake_power_off_enable ---when 1 then PMU is not really power off and when 0 PMU is really power off +;pmu_temp_protect_en --- 0:temperature protect disable 1:enable +;pmu_charge_ltf --- +;pmu_charge_htf --- +;pmu_discharge_ltf --- +;pmu_discharge_htf --- +;pmu_temp_para1 --- temp -25 voltage +;pmu_temp_para2 --- temp -15 voltage +;pmu_temp_para3 --- temp -10 voltage +;pmu_temp_para4 --- temp -5 voltage +;pmu_temp_para5 --- temp 0 voltage +;pmu_temp_para6 --- temp 5 voltage +;pmu_temp_para7 --- temp 10 voltage +;pmu_temp_para8 --- temp 20 voltage +;pmu_temp_para9 --- temp 30 voltage +;pmu_temp_para10 --- temp 40 voltage +;pmu_temp_para11 --- temp 45 voltage +;pmu_temp_para12 --- temp 50 voltage +;pmu_temp_para13 --- temp 55 voltage +;pmu_temp_para14 --- temp 60 voltage +;pmu_temp_para15 --- temp 70 voltage +;pmu_temp_para16 --- temp 80 voltage +;-------------------------------------------------------------------------------------------------------- +[pmu_para] +pmu_used = 1 +pmu_twi_addr = 0x34 +pmu_twi_id = 1 +pmu_irq_id = 0 +pmu_battery_rdc = 100 +pmu_battery_cap = 0 +pmu_batdeten = 1 +pmu_runtime_chgcur = 900 +pmu_earlysuspend_chgcur = 900 +pmu_suspend_chgcur = 2100 +pmu_shutdown_chgcur = 2100 +pmu_init_chgvol = 4200 +pmu_init_chgend_rate = 15 +pmu_init_chg_enabled = 1 +pmu_init_adc_freq = 800 +pmu_init_adcts_freq = 800 +pmu_init_chg_pretime = 70 +pmu_init_chg_csttime = 720 +pmu_batt_cap_correct = 1 +pmu_bat_regu_en = 0 + +pmu_bat_para1 = 0 +pmu_bat_para2 = 0 +pmu_bat_para3 = 0 +pmu_bat_para4 = 0 +pmu_bat_para5 = 0 +pmu_bat_para6 = 0 +pmu_bat_para7 = 0 +pmu_bat_para8 = 0 +pmu_bat_para9 = 1 +pmu_bat_para10 = 1 +pmu_bat_para11 = 2 +pmu_bat_para12 = 2 +pmu_bat_para13 = 3 +pmu_bat_para14 = 5 +pmu_bat_para15 = 11 +pmu_bat_para16 = 17 +pmu_bat_para17 = 21 +pmu_bat_para18 = 29 +pmu_bat_para19 = 36 +pmu_bat_para20 = 41 +pmu_bat_para21 = 46 +pmu_bat_para22 = 50 +pmu_bat_para23 = 57 +pmu_bat_para24 = 64 +pmu_bat_para25 = 70 +pmu_bat_para26 = 80 +pmu_bat_para27 = 83 +pmu_bat_para28 = 87 +pmu_bat_para29 = 87 +pmu_bat_para30 = 91 +pmu_bat_para31 = 95 +pmu_bat_para32 = 100 + +pmu_usbvol_limit = 0 +pmu_usbcur_limit = 0 +pmu_usbvol = 4000 +pmu_usbcur = 0 +pmu_usbvol_pc = 4400 +pmu_usbcur_pc = 500 +pmu_pwroff_vol = 3300 +pmu_pwron_vol = 2600 +pmu_pekoff_time = 6000 +pmu_pekoff_func = 1 +pmu_pekoff_en = 1 +pmu_peklong_time = 1000 +pmu_pekon_time = 1000 +pmu_pwrok_time = 64 +pmu_battery_warning_level1 = 3 +pmu_battery_warning_level2 = 0 +pmu_restvol_adjust_time = 60 +pmu_ocv_cou_adjust_time = 60 +pmu_chgled_func = 0 +pmu_chgled_type = 0 +pmu_vbusen_func = 1 +pmu_reset = 0 +pmu_IRQ_wakeup = 0 +pmu_hot_shutdowm = 1 +pmu_inshort = 1 +power_start = 1 +pmu_fake_power_off_enable = 0 +pmu_temp_protect_en = 0 +pmu_charge_ltf = 2261 +pmu_charge_htf = 388 +pmu_discharge_ltf = 3123 +pmu_discharge_htf = 237 +pmu_temp_para1 = 7748 +pmu_temp_para2 = 4610 +pmu_temp_para3 = 3605 +pmu_temp_para4 = 2843 +pmu_temp_para5 = 2261 +pmu_temp_para6 = 1811 +pmu_temp_para7 = 1462 +pmu_temp_para8 = 972 +pmu_temp_para9 = 662 +pmu_temp_para10 = 461 +pmu_temp_para11 = 388 +pmu_temp_para12 = 328 +pmu_temp_para13 = 278 +pmu_temp_para14 = 237 +pmu_temp_para15 = 175 +pmu_temp_para16 = 130 + +;---------------------------------------------------------------------------------- +; dvfs voltage-frequency table configuration for general ic version +; +; max_freq: cpu maximum frequency, based on Hz, can not be more than 1008MHz +; min_freq: cpu minimum frequency, based on Hz, can not be less than 96MHz +; +; temp_limit_freq: cpu maximum frequency according to tempreture limit +; temp_limit_high: set cpu max freq to temp_limit_freq when tempreture > temp_limit_high +; temp_limit_low: set cpu max freq to max_freq when tempreture < temp_limit_low +; temp_limit_low must be less than temp_limit_high, otherwise invalid +; +; LV_count: count of LV_freq/LV_volt, must be < 16 +; +; LV1: core vdd is 1.26v if cpu frequency is (1104Mhz, xxxxMhz] +; LV2: core vdd is 1.26v if cpu frequency is (1056Mhz, 1104Mhz] +; LV3: core vdd is 1.20v if cpu frequency is (864Mhz, 1056Mhz] +; LV4: core vdd is 1.10v if cpu frequency is (720Mhz, 864Mhz] +; LV5: core vdd is 1.00v if cpu frequency is (480Mhz, 720Mhz] +; LV6: core vdd is 0.90v if cpu frequency is (0Mhz, 480Mhz] +; LV7: core vdd is 0.90v if cpu frequency is (0Mhz, 480Mhz] +; LV8: core vdd is 0.90v if cpu frequency is (0Mhz, 480Mhz] +; +;---------------------------------------------------------------------------------- +[dvfs_table] +max_freq = 1200000000 +min_freq = 120000000 + +temp_limit_freq = 1008000000 +temp_limit_high = 85 +temp_limit_low = 75 + +LV_count = 8 + +LV1_freq = 1200000000 +LV1_volt = 1500 + +LV2_freq = 1116000000 +LV2_volt = 1400 + +LV3_freq = 1008000000 +LV3_volt = 1260 + +LV4_freq = 864000000 +LV4_volt = 1200 + +LV5_freq = 720000000 +LV5_volt = 1100 + +LV6_freq = 480000000 +LV6_volt = 1000 + +LV7_freq = 0 +LV7_volt = 1000 + +LV8_freq = 0 +LV8_volt = 1000 + +;---------------------------------------------------------------------------------- +; dvfs voltage-frequency table configuration for ic D version +; +; max_freq: cpu maximum frequency, based on Hz, can not be more than 1008MHz +; min_freq: cpu minimum frequency, based on Hz, can not be less than 96MHz +; +; temp_limit_freq: cpu maximum frequency according to tempreture limit +; temp_limit_high: set cpu max freq to temp_limit_freq when tempreture > temp_limit_high +; temp_limit_low: set cpu max freq to max_freq when tempreture < temp_limit_low +; temp_limit_low must be less than temp_limit_high, otherwise invalid +; +; LV_count: count of LV_freq/LV_volt, must be < 16 +; +; LV1: core vdd is 1.20v if cpu frequency is (1116Mhz, xxxxMhz] +; LV2: core vdd is 1.16v if cpu frequency is (1056Mhz, 1116Mhz] +; LV3: core vdd is 1.10v if cpu frequency is (900Mhz, 1056Mhz] +; LV4: core vdd is 1.06v if cpu frequency is (828Mhz, 900Mhz] +; LV5: core vdd is 1.00v if cpu frequency is (720Mhz, 828Mhz] +; LV6: core vdd is 0.96v if cpu frequency is (600Mhz, 720Mhz] +; LV7: core vdd is 0.90v if cpu frequency is (0Mhz, 480Mhz] +; LV8: core vdd is 0.90v if cpu frequency is (0Mhz, 480Mhz] +; +;---------------------------------------------------------------------------------- +[ver_d_dvfs_table] +max_freq = 1200000000 +min_freq = 120000000 + +temp_limit_freq = 1008000000 +temp_limit_high = 85 +temp_limit_low = 75 + +LV_count = 8 + +LV1_freq = 1200000000 +LV1_volt = 1500 + +LV2_freq = 1116000000 +LV2_volt = 1400 + +LV3_freq = 1008000000 +LV3_volt = 1260 + +LV4_freq = 864000000 +LV4_volt = 1200 + +LV5_freq = 720000000 +LV5_volt = 1100 + +LV6_freq = 480000000 +LV6_volt = 1000 + +LV7_freq = 0 +LV7_volt = 1000 + +LV8_freq = 0 +LV8_volt = 1000 + +;---------------------------------------------------------------------------------- +;cpus config parameters +;cpus_uart_debug_used --r_uart whether used for cpus debugging +; +;---------------------------------------------------------------------------------- +[cpus_config_paras] +cpus_uart_debug_used = 1 + diff --git a/3.3/displays/TOPWAY_LMT104SBH01-NNC.fex b/3.3/displays/TOPWAY_LMT104SBH01-NNC.fex new file mode 100644 index 0000000..6dfff69 --- /dev/null +++ b/3.3/displays/TOPWAY_LMT104SBH01-NNC.fex @@ -0,0 +1,977 @@ +[product] +version = "301" +machine = "pangolin" + +[platform] +eraseflag = 1 + +[fel_key] +fel_key_type = 1 + +[target] +boot_clock = 1008 +storage_type = -1 +power_start = 3 + +[power_sply] +dcdc1_vol = 3300 +dcdc2_vol = 1200 +dcdc3_vol = 1260 +dcdc4_vol = 1260 +dcdc5_vol = 1500 +aldo1_vol = 0 +aldo2_vol = 1800 +aldo3_vol = 3000 +eldo1_vol = 0 +eldo2_vol = 0 +eldo3_vol = 0 + +[card_boot] +logical_start = 40960 +sprite_gpio0 = + +[pm_para] +standby_mode = 0 +dram_selfresh_en = 0 + +[card0_boot_para] +card_ctrl = 0 +card_high_speed = 1 +card_line = 4 +sdc_d1 = port:PF00<2><1> +sdc_d0 = port:PF01<2><1> +sdc_clk = port:PF02<2><1> +sdc_cmd = port:PF03<2><1> +sdc_d3 = port:PF04<2><1> +sdc_d2 = port:PF05<2><1> + +[twi_para] +twi_port = 0 +twi_scl = port:PH14<2> +twi_sda = port:PH15<2> + +[uart_para] +uart_debug_port = 0 +uart_debug_tx = port:PH20<2><1> +uart_debug_rx = port:PH21<2><1> + +[jtag_para] +jtag_enable = 1 +jtag_ms = port:PH09<3> +jtag_ck = port:PH10<3> +jtag_do = port:PH11<3> +jtag_di = port:PH12<3> + +[clock] +pll3 = 297 +pll4 = 300 +pll6 = 600 +pll7 = 297 +pll8 = 360 +pll9 = 297 +pll10 = 702 + +[dram_para] +dram_clk = 480 +dram_type = 3 +dram_zq = 0x46 +dram_odt_en = 1 +dram_para1 = 283247616 +dram_para2 = 4353 +dram_mr0 = 5696 +dram_mr1 = 64 +dram_mr2 = 8 +dram_mr3 = 0 +dram_tpr0 = 0x0 +dram_tpr1 = 0x80000400 +dram_tpr2 = 0x3ea70140 +dram_tpr3 = 0xa08b063c +dram_tpr4 = 0x2946c208 +dram_tpr5 = 0x67443a23 +dram_tpr6 = 0x30028580 +dram_tpr7 = 0x2a3297 +dram_tpr8 = 0x5034fa8 +dram_tpr9 = 0x36353d8 +dram_tpr10 = 0x0 +dram_tpr11 = 0x0 +dram_tpr12 = 0x0 +dram_tpr13 = 0x0 + +[gmac_para] +gmac_used = 1 +gmac_txd0 = port:PA00<2><3> +gmac_txd1 = port:PA01<2><3> +gmac_txd2 = port:PA02<2><3> +gmac_txd3 = port:PA03<2><3> +gmac_txclk = port:PA10<2><3> +gmac_txen = port:PA09<2><3> +gmac_rxd0 = port:PA11<2><3> +gmac_rxd1 = port:PA12<2><3> +gmac_rxd2 = port:PA13<2><3> +gmac_rxd3 = port:PA14<2><3> +gmac_rxdv = port:PA19<2><3> +gmac_rxclk = port:PA20<2><3> +gmac_clkin = port:PA25<2><3> +gmac_mdc = port:PA26<2><1><3> +gmac_mdio = port:PA27<2><1><3> + +[twi0_para] +twi_used = 1 +twi_scl = port:PH14<2> +twi_sda = port:PH15<2> + +[twi1_para] +twi_used = 1 +twi_scl = port:PH16<2> +twi_sda = port:PH17<2> + +[twi2_para] +twi_used = 1 +twi_scl = port:PH18<2> +twi_sda = port:PH19<2> + +[twi3_para] +twi_used = 1 +twi_scl = port:PB05<4> +twi_sda = port:PB06<4> + +[uart_para0] +uart_used = 1 +uart_port = 0 +uart_type = 2 +uart_tx = port:PH20<2><1> +uart_rx = port:PH21<2><1> + +[uart_para1] +uart_used = 1 +uart_port = 1 +uart_type = 2 +uart_tx = port:PA04<4><1> +uart_rx = port:PA05<4><1> + +[uart_para2] +uart_used = 1 +uart_port = 2 +uart_type = 4 +uart_tx = port:PG06<2><1> +uart_rx = port:PG07<2><1> +uart_rts = port:PG08<2><1> +uart_cts = port:PG09<2><1> + +[uart_para3] +uart_used = 0 +uart_port = 3 +uart_type = 4 +uart_tx = port:PB05<3><1> +uart_rx = port:PB06<3><1> +uart_rts = port:PB04<3><1> +uart_cts = port:PB00<3><1> + +[uart_para4] +uart_used = 0 +uart_port = 4 +uart_type = 2 +uart_tx = port:PG17<2><1> +uart_rx = port:PG18<2><1> +uart_rts = port:PB04<3><1> +uart_cts = port:PB00<3><1> + +[uart_para5] +uart_used = 0 +uart_port = 5 +uart_type = 4 +uart_tx = port:PE04<3><1> +uart_rx = port:PE05<3><1> +uart_rts = port:PE06<3><1> +uart_cts = port:PE07<3><1> + +[spi0_para] +spi_used = 0 +spi_cs_bitmap = 1 +spi_cs0 = port:PC27<3><1> +spi_sclk = port:PC02<3> +spi_mosi = port:PC00<3> +spi_miso = port:PC01<3> + +[spi1_para] +spi_used = 1 +spi_cs_bitmap = 3 +spi_cs1 = port:PG12<2><1> +spi_cs0 = port:PG13<2><1> +spi_sclk = port:PG14<2> +spi_mosi = port:PG15<2> +spi_miso = port:PG16<2> + +[spi2_para] +spi_used = 0 +spi_cs_bitmap = 1 +spi_cs0 = port:PH09<2> +spi_sclk = port:PH10<2> +spi_mosi = port:PH11<2> +spi_miso = port:PH12<2> + +[spi3_para] +spi_used = 0 +spi_cs_bitmap = 1 +spi_cs0 = port:PA21<4> +spi_sclk = port:PA22<4> +spi_mosi = port:PA23<4> +spi_miso = port:PA24<4> +spi_cs1 = port:PA25<4> + +[rtp_para] +rtp_used = 0 +rtp_screen_size = 5 +rtp_regidity_level = 5 +rtp_press_threshold_enable = 0 +rtp_press_threshold = 0x1f40 +rtp_sensitive_level = 0xf +rtp_exchange_x_y_flag = 0 + +[ctp_para] +ctp_used = 0 +ctp_name = "gsl1680" +ctp_twi_id = 1 +ctp_twi_addr = 0x40 +ctp_screen_max_x = 800 +ctp_screen_max_y = 480 +ctp_revert_x_flag = 0 +ctp_revert_y_flag = 0 +ctp_exchange_x_y_flag = 0 + +[tkey_para] +tkey_used = 0 +tkey_twi_id = +tkey_twi_addr = +tkey_int = + +[motor_para] +motor_used = 0 +motor_shake = port:power3<1><1> + +[nand0_para] +nand_support_2ch = 0 +nand0_used = 0 +good_block_ratio = 944 +nand0_we = port:PC00<2> +nand0_ale = port:PC01<2> +nand0_cle = port:PC02<2> +nand0_ce1 = port:PC03<2> +nand0_ce0 = port:PC04<2> +nand0_nre = port:PC05<2> +nand0_rb0 = port:PC06<2> +nand0_rb1 = port:PC07<2> +nand0_d0 = port:PC08<2> +nand0_d1 = port:PC09<2> +nand0_d2 = port:PC10<2> +nand0_d3 = port:PC11<2> +nand0_d4 = port:PC12<2> +nand0_d5 = port:PC13<2> +nand0_d6 = port:PC14<2> +nand0_d7 = port:PC15<2> +nand0_ce2 = port:PC25<2> +nand0_ce3 = port:PC26<2> +nand0_ndqs = port:PC24<2> + +[nand1_para] +nand1_used = 0 +nand1_we = port:PH00<2> +nand1_ale = port:PH01<2> +nand1_cle = port:PH02<2> +nand1_ce1 = port:PH03<2> +nand1_ce0 = port:PH04<2> +nand1_nre = port:PH05<2> +nand1_rb0 = port:PH06<2> +nand1_rb1 = port:PH07<2> +nand1_d0 = port:PC16<3> +nand1_d1 = port:PC17<3> +nand1_d2 = port:PC18<3> +nand1_d3 = port:PC19<3> +nand1_d4 = port:PC20<3> +nand1_d5 = port:PC21<3> +nand1_d6 = port:PC22<3> +nand1_d7 = port:PC23<3> +nand1_ce2 = port:PH29<2> +nand1_ce3 = port:PH30<2> +nand1_ndqs = port:PH08<2> + +[boot_disp] + +[disp_init] +disp_init_enable = 1 +disp_mode = 2 +screen0_output_type = 1 +screen0_output_mode = 4 +screen1_output_type = 3 +screen1_output_mode = 9 +fb0_format = 0 +fb0_pixel_sequence = 0 +fb0_scaler_mode_enable = 0 +fb0_width = 800 +fb0_height = 600 +fb1_format = 0 +fb1_pixel_sequence = 0 +fb1_scaler_mode_enable = 0 +fb1_width = 1920 +fb1_height = 1080 +lcd0_backlight = 200 +lcd1_backlight = 50 +lcd0_bright = 50 +lcd0_contrast = 50 +lcd0_saturation = 57 +lcd0_hue = 50 +lcd1_bright = 50 +lcd1_contrast = 50 +lcd1_saturation = 57 +lcd1_hue = 50 + +[lcd0_para] +lcd_used = 1 +lcd_driver_name = "default_lcd" +lcd_size = "7.08" +lcd_if = 3 +lcd_x = 800 +lcd_y = 600 +lcd_width = 155 +lcd_height = 90 +lcd_dclk_freq = 38 +lcd_pwm_used = 1 +lcd_pwm_ch = 0 +lcd_pwm_freq = 50000 +lcd_pwm_pol = 0 +lcd_hbp = 112 +lcd_ht = 1024 +lcd_hspw = 112 +lcd_vbp = 17 +lcd_vt = 624 +lcd_vspw = 7 +lcd_lvds_if = 0 +lcd_lvds_colordepth = 1 +lcd_lvds_mode = 0 +lcd_frm = 1 +lcd_hv_clk_phase = 0 +lcd_hv_sync_polarity = 0 +lcd_gamma_en = 0 +lcd_bright_curve_en = 0 +lcd_cmap_en = 0 +deu_mode = 0 +lcdgamma4iep = 22 +smartbl_low_limit = 85 +smart_color = 90 +lcd_bl_en = port:PD20<1><0><1> +lcd_power = port:PD21<1><0><1> +lcd_pwm = port:PH13<2><0> +lcdd0 = port:PD00<3><0><3> +lcdd1 = port:PD01<3><0><3> +lcdd2 = port:PD02<3><0><3> +lcdd3 = port:PD03<3><0><3> +lcdd4 = port:PD04<3><0><3> +lcdd5 = port:PD05<3><0><3> +lcdd6 = port:PD06<3><0><3> +lcdd7 = port:PD07<3><0><3> + +[hdmi_para] +hdmi_used = 1 + +[vip0_para] +vip_used = 0 +vip_mode = 0 +vip_dev_qty = 1 +vip_vip_mck = port:PE16<2> +vip_dev0_mname = "" +vip_dev0_lane = 2 +vip_dev0_twi_id = 0 +vip_dev0_twi_addr = 108 +vip_dev0_isp_used = 1 +vip_dev0_fmt = 1 +vip_dev0_stby_mode = 0 +vip_dev0_vflip = 0 +vip_dev0_hflip = 0 +vip_dev0_iovdd = "axp22_dldo3" +vip_dev0_iovdd_vol = 2800000 +vip_dev0_avdd = "axp22_ldoio0" +vip_dev0_avdd_vol = 2800000 +vip_dev0_dvdd = "axp22_eldo2" +vip_dev0_dvdd_vol = 1500000 +vip_dev0_afvdd = "" +vip_dev0_afvdd_vol = 2800000 +vip_dev0_power_en = +vip_dev0_reset = +vip_dev0_pwdn = +vip_dev0_flash_en = +vip_dev0_flash_mode = +vip_dev0_af_pwdn = +vip_dev0_act_used = 1 +vip_dev0_act_name = "ad5820_act" +vip_dev0_act_slave = 24 +vip_dev1_mname = "" +vip_dev1_lane = 1 +vip_dev1_twi_id = 0 +vip_dev1_twi_addr = +vip_dev1_isp_used = 0 +vip_dev1_fmt = 1 +vip_dev1_stby_mode = 0 +vip_dev1_vflip = 0 +vip_dev1_hflip = 0 +vip_dev1_iovdd = "axp22_dldo3" +vip_dev1_iovdd_vol = 2800000 +vip_dev1_avdd = "axp22_ldoio0" +vip_dev1_avdd_vol = 2800000 +vip_dev1_dvdd = "axp22_eldo2" +vip_dev1_dvdd_vol = 1800000 +vip_dev1_afvdd = "" +vip_dev1_afvdd_vol = 2800000 +vip_dev1_power_en = +vip_dev1_reset = +vip_dev1_pwdn = +vip_dev1_flash_en = +vip_dev1_flash_mode = +vip_dev1_af_pwdn = + +[vip1_para] +vip_used = 0 +vip_mode = 0 +vip_dev_qty = 1 +vip_csi_pck = port:PE00<2> +vip_csi_mck = port:PE01<2> +vip_csi_hsync = port:PE02<2> +vip_csi_vsync = port:PE03<2> +vip_csi_d0 = +vip_csi_d1 = +vip_csi_d2 = +vip_csi_d3 = +vip_csi_d4 = port:PE08<2> +vip_csi_d5 = port:PE09<2> +vip_csi_d6 = port:PE10<2> +vip_csi_d7 = port:PE11<2> +vip_csi_d8 = port:PE12<2> +vip_csi_d9 = port:PE13<2> +vip_csi_d10 = port:PE14<2> +vip_csi_d11 = port:PE15<2> +vip_dev0_mname = "s5k4ec" +vip_dev0_twi_id = 0 +vip_dev0_twi_addr = 90 +vip_dev0_isp_used = 0 +vip_dev0_fmt = 0 +vip_dev0_stby_mode = 0 +vip_dev0_vflip = 0 +vip_dev0_hflip = 1 +vip_dev0_iovdd = "axp22_dldo3" +vip_dev0_iovdd_vol = 2800000 +vip_dev0_avdd = "axp22_ldoio0" +vip_dev0_avdd_vol = 2800000 +vip_dev0_dvdd = "axp22_eldo1" +vip_dev0_dvdd_vol = 1500000 +vip_dev0_afvdd = "" +vip_dev0_afvdd_vol = 2800000 +vip_dev0_power_en = port:PE07<1><1> +vip_dev0_reset = port:PG12<1><0> +vip_dev0_pwdn = port:PH28<1><1> +vip_dev0_flash_en = +vip_dev0_flash_mode = +vip_dev0_af_pwdn = +vip_dev0_act_used = 0 +vip_dev0_act_name = "" +vip_dev0_act_slave = 90 +vip_dev1_mname = "" +vip_dev1_twi_id = 0 +vip_dev1_twi_addr = 120 +vip_dev1_stby_mode = 0 +vip_dev1_isp_used = 0 +vip_dev1_fmt = 0 +vip_dev1_vflip = 0 +vip_dev1_hflip = 0 +vip_dev1_iovdd = "axp22_dldo3" +vip_dev1_iovdd_vol = 2800000 +vip_dev1_avdd = "axp22_ldoio0" +vip_dev1_avdd_vol = 2800000 +vip_dev1_dvdd = "axp22_eldo2" +vip_dev1_dvdd_vol = 1800000 +vip_dev1_afvdd = "" +vip_dev1_afvdd_vol = 2800000 +vip_dev1_power_en = +vip_dev1_reset = port:PG12<1><0> +vip_dev1_pwdn = port:PH28<1><1> +vip_dev1_flash_en = +vip_dev1_flash_mode = +vip_dev1_af_pwdn = + +[camera_list_para] +camera_list_para_used = 0 +ov7670 = 0 +gc0308 = 0 +gt2005 = 0 +hi704 = 0 +sp0838 = 0 +mt9m112 = 0 +mt9m113 = 0 +gc2035 = 0 +ov2655 = 0 +hi253 = 0 +gc0307 = 0 +mt9d112 = 0 +ov5640 = 1 +ov5647 = 0 +gc2015 = 0 +ov2643 = 0 +gc0329 = 0 +gc0309 = 0 +tvp5150 = 0 +s5k4ec = 1 +ov5650_mv9335 = 0 +tw2866 = 0 + +[tvout_para] +tvout_used = +tvout_channel_num = +tv_en = + +[tvin_para] +tvin_used = +tvin_channel_num = + +[mmc0_para] +sdc_used = 1 +sdc_detmode = 1 +sdc_buswidth = 4 +sdc_clk = port:PF02<2><1><2> +sdc_cmd = port:PF03<2><1><2> +sdc_d0 = port:PF01<2><1><2> +sdc_d1 = port:PF00<2><1><2> +sdc_d2 = port:PF05<2><1><2> +sdc_d3 = port:PF04<2><1><2> +sdc_det = port:PC19<0><1><2> +sdc_use_wp = 0 +sdc_wp = port:PC18<0><1><1> +sdc_isio = 0 +sdc_regulator = "none" + +[mmc1_para] +sdc_used = 0 +sdc_detmode = 4 +sdc_buswidth = 4 +sdc_clk = port:PG00<2><1><2> +sdc_cmd = port:PG01<2><1><2> +sdc_d0 = port:PG02<2><1><2> +sdc_d1 = port:PG03<2><1><2> +sdc_d2 = port:PG04<2><1><2> +sdc_d3 = port:PG05<2><1><2> +sdc_det = +sdc_use_wp = 0 +sdc_wp = +sdc_isio = 1 +sdc_regulator = "none" + +[mmc2_para] +sdc_used = 1 +sdc_detmode = 3 +sdc_buswidth = 8 +sdc_clk = port:PC07<3><1><2> +sdc_cmd = port:PC06<3><1><2> +sdc_d0 = port:PC08<3><1><2> +sdc_d1 = port:PC09<3><1><2> +sdc_d2 = port:PC10<3><1><2> +sdc_d3 = port:PC11<3><1><2> +sdc_d4 = port:PC12<3><1><2> +sdc_d5 = port:PC13<3><1><2> +sdc_d6 = port:PC14<3><1><2> +sdc_d7 = port:PC15<3><1><2> +emmc_rst = port:PC24<3><1><2> +sdc_det = +sdc_use_wp = 0 +sdc_wp = +sdc_isio = 0 +sdc_regulator = "none" + +[mmc3_para] +sdc_used = 0 +sdc_detmode = 2 +sdc_buswidth = 4 +sdc_clk = port:PA10<2><1><2> +sdc_cmd = port:PA09<2><1><2> +sdc_d0 = port:PA11<2><1><2> +sdc_d1 = port:PA12<2><1><2> +sdc_d2 = port:PA13<2><1><2> +sdc_d3 = port:PA14<2><1><2> +sdc_det = +sdc_use_wp = 0 +sdc_wp = +sdc_isio = 0 +sdc_regulator = "none" + +[smc_para] +smc_used = +smc_rst = +smc_vppen = +smc_vppp = +smc_det = +smc_vccen = +smc_sck = +smc_sda = + +[usbc0] +usb_used = 1 +usb_port_type = 2 +usb_detect_type = 1 +usb_id_gpio = port:PH02<0><1> +usb_det_vbus_gpio = port:PD23<0><0> +usb_drv_vbus_gpio = port:PH30<1><0><0> +usb_restrict_gpio = port:PH30<1><0><0> +usb_host_init_state = 0 +usb_restric_flag = 0 +usb_restric_voltage = 3550000 +usb_restric_capacity = 5 + +[usbc1] +usb_used = 1 +usb_port_type = 1 +usb_detect_type = 0 +usb_id_gpio = +usb_det_vbus_gpio = +usb_drv_vbus_gpio = +usb_restrict_gpio = +usb_host_init_state = 1 +usb_restric_flag = 0 +usb_not_suspend = 0 + +[usbc2] +usb_used = 1 +usb_port_type = 1 +usb_detect_type = 0 +usb_id_gpio = +usb_det_vbus_gpio = +usb_drv_vbus_gpio = +usb_restrict_gpio = +usb_host_init_state = 1 +usb_restric_flag = 0 +usb_not_suspend = 0 + +[usbc3] +usb_used = 1 +usb_port_type = 1 +usb_detect_type = 0 +usb_host_init_state = 1 +usb_restric_flag = 0 +usb_not_suspend = 0 + +[usb_feature] +vendor_id = 6353 +mass_storage_id = 1 +adb_id = 2 +manufacturer_name = "USB Developer" +product_name = "Android" +serial_number = "12345678" + +[fastboot_feature] +manufacturer_name = "Theobroma Systems" +product_name = "A31-uQ7" + +[serial_feature] +serial_unique = "1" + +[msc_feature] +vendor_name = "USB 2.0" +product_name = "USB Flash Driver" +release = 100 +luns = 3 + +[gsensor_para] +gsensor_used = 0 +gsensor_twi_id = 2 +gsensor_twi_addr = 0x18 +gsensor_int1 = port:PA09<6><1> +gsensor_int2 = + +[vga_para] +vga_used = 0 +vga_en = port:PH25<1><1> + +[sn7325_para] +sn7325_used = 0 +sn7325_twi_id = 2 +sn7325_twi_addr = 88 + +[gps_para] + +[wifi_para] +wifi_used = 1 +wifi_sdc_id = 1 +wifi_usbc_id = 1 +wifi_usbc_type = 1 +wifi_mod_sel = 6 +wifi_power = "axp22_aldo1" +ap6xxx_wl_regon = port:PG10<1><0> +ap6xxx_wl_host_wake = port:PG11<0><0> +ap6xxx_bt_regon = port:PL08<1><0> +ap6xxx_bt_wake = port:PL07<1><0> +ap6xxx_bt_host_wake = port:PL06<0><0> + +[3g_para] +3g_used = 0 +3g_usbc_num = 2 +3g_uart_num = 0 +bb_name = "cwm600" +bb_vbat = port:PA22<1><0> +bb_pwr_on = port:PM01<1><0> +bb_wake = port:PM02<1><1> +bb_rst = port:PM03<1><0> +bb_dldo = +bb_dldo_min_uV = +bb_dldo_max_uV = + +[gy_para] +gy_used = 0 +gy_twi_id = 2 +gy_twi_addr = 106 +gy_int1 = port:PA10<6><1> +gy_int2 = + +[ls_para] +ls_used = 0 +ls_twi_id = 2 +ls_twi_addr = 35 +ls_int = port:PA12<6><1> + +[compass_para] +compass_used = 0 +compass_twi_id = 2 +compass_twi_addr = 13 +compass_int = port:PA11<6><1> + +[bt_para] +bt_used = 0 +bt_uart_id = 2 +bt_wakeup = +bt_gpio = +bt_rst = + +[i2s_para] +i2s_used = 0 +i2s_channel = 2 +i2s_master = 1 +i2s_select = 0 +audio_format = 4 +signal_inversion = 3 +over_sample_rate = 256 +sample_resolution = 16 +word_select_size = 32 +pcm_sync_period = 256 +msb_lsb_first = 0 +sign_extend = 0 +slot_index = 0 +slot_width = 16 +frame_width = 1 +tx_data_mode = 0 +rx_data_mode = 0 +i2s_mclk = +i2s_bclk = port:PB01<2><1> +i2s_lrclk = port:PB02<2><1> +i2s_dout0 = port:PB03<2><1> +i2s_dout1 = +i2s_dout2 = +i2s_dout3 = +i2s_din = port:PB07<2><1> + +[pcm_para] +pcm_used = 0 +pcm_channel = 2 +pcm_master = 4 +pcm_select = 1 +audio_format = 4 +signal_inversion = 3 +over_sample_rate = 512 +sample_resolution = 16 +word_select_size = 32 +pcm_sync_period = 64 +msb_lsb_first = 0 +sign_extend = 0 +slot_index = 0 +slot_width = 16 +frame_width = 1 +tx_data_mode = 0 +rx_data_mode = 0 +pcm_mclk = +pcm_bclk = port:PG13<3><1> +pcm_lrclk = port:PG14<3><1> +pcm_dout = port:PG16<3><1> +pcm_din = port:PG15<3><1> + +[spdif_para] +spdif_used = 0 +spdif_dout = port:PH28<3><1> +spdif_din = port:PH27<3><1> + +[audio_para] +audio_used = 0 +audio_hp_ldo = "none" +headphone_vol = 59 +earpiece_vol = 59 +cap_vol = 5 +pa_single_vol = 25 +pa_double_used = 0 +pa_double_vol = 31 +headphone_direct_used = 0 +headphone_mute_used = 0 +audio_pa_ctrl = port:PH22<1><0> +audio_mute_ctrl = port:PH23<1><0> +headset_mic_vol = 6 +main_mic_vol = 6 + +[ir_para] +ir_used = 0 +ir_rx = port:PL04<2><1> +ir_power_key_code = 0 + +[pmu_para] +pmu_used = 1 +pmu_twi_addr = 52 +pmu_twi_id = 1 +pmu_irq_id = 0 +pmu_battery_rdc = 100 +pmu_battery_cap = 0 +pmu_batdeten = 1 +pmu_runtime_chgcur = 900 +pmu_earlysuspend_chgcur = 900 +pmu_suspend_chgcur = 2100 +pmu_shutdown_chgcur = 2100 +pmu_init_chgvol = 4200 +pmu_init_chgend_rate = 15 +pmu_init_chg_enabled = 1 +pmu_init_adc_freq = 800 +pmu_init_adcts_freq = 800 +pmu_init_chg_pretime = 70 +pmu_init_chg_csttime = 720 +pmu_batt_cap_correct = 1 +pmu_bat_regu_en = 0 +pmu_bat_para1 = 0 +pmu_bat_para2 = 0 +pmu_bat_para3 = 0 +pmu_bat_para4 = 0 +pmu_bat_para5 = 0 +pmu_bat_para6 = 0 +pmu_bat_para7 = 0 +pmu_bat_para8 = 0 +pmu_bat_para9 = 1 +pmu_bat_para10 = 1 +pmu_bat_para11 = 2 +pmu_bat_para12 = 2 +pmu_bat_para13 = 3 +pmu_bat_para14 = 5 +pmu_bat_para15 = 11 +pmu_bat_para16 = 17 +pmu_bat_para17 = 21 +pmu_bat_para18 = 29 +pmu_bat_para19 = 36 +pmu_bat_para20 = 41 +pmu_bat_para21 = 46 +pmu_bat_para22 = 50 +pmu_bat_para23 = 57 +pmu_bat_para24 = 64 +pmu_bat_para25 = 70 +pmu_bat_para26 = 80 +pmu_bat_para27 = 83 +pmu_bat_para28 = 87 +pmu_bat_para29 = 87 +pmu_bat_para30 = 91 +pmu_bat_para31 = 95 +pmu_bat_para32 = 100 +pmu_usbvol_limit = 0 +pmu_usbcur_limit = 0 +pmu_usbvol = 4000 +pmu_usbcur = 0 +pmu_usbvol_pc = 4400 +pmu_usbcur_pc = 500 +pmu_pwroff_vol = 3300 +pmu_pwron_vol = 2600 +pmu_pekoff_time = 6000 +pmu_pekoff_func = 1 +pmu_pekoff_en = 1 +pmu_peklong_time = 1000 +pmu_pekon_time = 1000 +pmu_pwrok_time = 64 +pmu_battery_warning_level1 = 3 +pmu_battery_warning_level2 = 0 +pmu_restvol_adjust_time = 60 +pmu_ocv_cou_adjust_time = 60 +pmu_chgled_func = 0 +pmu_chgled_type = 0 +pmu_vbusen_func = 1 +pmu_reset = 0 +pmu_IRQ_wakeup = 0 +pmu_hot_shutdowm = 1 +pmu_inshort = 1 +power_start = 1 +pmu_fake_power_off_enable = 0 +pmu_temp_protect_en = 0 +pmu_charge_ltf = 2261 +pmu_charge_htf = 388 +pmu_discharge_ltf = 3123 +pmu_discharge_htf = 237 +pmu_temp_para1 = 7748 +pmu_temp_para2 = 4610 +pmu_temp_para3 = 3605 +pmu_temp_para4 = 2843 +pmu_temp_para5 = 2261 +pmu_temp_para6 = 1811 +pmu_temp_para7 = 1462 +pmu_temp_para8 = 972 +pmu_temp_para9 = 662 +pmu_temp_para10 = 461 +pmu_temp_para11 = 388 +pmu_temp_para12 = 328 +pmu_temp_para13 = 278 +pmu_temp_para14 = 237 +pmu_temp_para15 = 175 +pmu_temp_para16 = 130 + +[dvfs_table] +max_freq = 1200000000 +min_freq = 120000000 +temp_limit_freq = 1008000000 +temp_limit_high = 85 +temp_limit_low = 75 +LV_count = 8 +LV1_freq = 1200000000 +LV1_volt = 1500 +LV2_freq = 1116000000 +LV2_volt = 1400 +LV3_freq = 1008000000 +LV3_volt = 1260 +LV4_freq = 864000000 +LV4_volt = 1200 +LV5_freq = 720000000 +LV5_volt = 1100 +LV6_freq = 480000000 +LV6_volt = 1000 +LV7_freq = 0 +LV7_volt = 1000 +LV8_freq = 0 +LV8_volt = 1000 + +[ver_d_dvfs_table] +max_freq = 1200000000 +min_freq = 120000000 +temp_limit_freq = 1008000000 +temp_limit_high = 85 +temp_limit_low = 75 +LV_count = 8 +LV1_freq = 1200000000 +LV1_volt = 1500 +LV2_freq = 1116000000 +LV2_volt = 1400 +LV3_freq = 1008000000 +LV3_volt = 1260 +LV4_freq = 864000000 +LV4_volt = 1200 +LV5_freq = 720000000 +LV5_volt = 1100 +LV6_freq = 480000000 +LV6_volt = 1000 +LV7_freq = 0 +LV7_volt = 1000 +LV8_freq = 0 +LV8_volt = 1000 + +[cpus_config_paras] +cpus_uart_debug_used = 1 + -- cgit v1.2.3