summaryrefslogtreecommitdiff
path: root/drivers/usbdcore_omap1510.c
blob: 7a908489f3a84139207f27c8329093f59646ed77 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
1192
1193
1194
1195
1196
1197
1198
1199
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
1248
1249
1250
1251
1252
1253
1254
1255
1256
1257
1258
1259
1260
1261
1262
1263
1264
1265
1266
1267
1268
1269
1270
1271
1272
1273
1274
1275
1276
1277
1278
1279
1280
1281
1282
1283
1284
1285
1286
1287
1288
1289
1290
1291
1292
1293
1294
1295
1296
1297
1298
1299
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
1341
1342
1343
1344
1345
1346
1347
1348
1349
1350
1351
1352
1353
1354
1355
1356
1357
1358
1359
1360
1361
1362
1363
1364
1365
1366
1367
1368
1369
1370
1371
1372
1373
1374
1375
1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
1387
1388
1389
1390
1391
1392
1393
1394
1395
1396
1397
1398
1399
1400
1401
1402
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
1416
1417
1418
1419
1420
1421
1422
1423
1424
1425
1426
1427
1428
1429
1430
1431
1432
1433
1434
1435
1436
1437
1438
1439
1440
1441
1442
1443
1444
1445
1446
1447
1448
1449
1450
1451
1452
1453
1454
1455
1456
1457
1458
1459
1460
1461
1462
1463
1464
1465
1466
1467
1468
1469
1470
1471
1472
1473
1474
1475
1476
1477
1478
1479
1480
1481
1482
1483
1484
1485
1486
1487
1488
1489
1490
1491
1492
1493
1494
1495
1496
/*
 * (C) Copyright 2003
 * Gerry Hamel, geh@ti.com, Texas Instruments
 *
 * Based on
 * linux/drivers/usb/device/bi/omap.c
 * TI OMAP1510 USB bus interface driver
 *
 * Author: MontaVista Software, Inc.
 *	   source@mvista.com
 *	   (C) Copyright 2002
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307	 USA
 *
 */

#include <common.h>

#if defined(CONFIG_OMAP1510) && defined(CONFIG_USB_DEVICE)

#include <asm/io.h>
#ifdef CONFIG_OMAP_SX1
#include <i2c.h>
#endif

#include "usbdcore.h"
#include "usbdcore_omap1510.h"
#include "usbdcore_ep0.h"


#define UDC_MAX_ENDPOINTS	     31 /* Number of endpoints on this UDC */

/* Some kind of debugging output... */
#if 1
#define UDCDBG(str)
#define UDCDBGA(fmt,args...)
#else  /* The bugs still exists... */
#define UDCDBG(str) serial_printf("[%s] %s:%d: " str "\n", __FILE__,__FUNCTION__,__LINE__)
#define UDCDBGA(fmt,args...) serial_printf("[%s] %s:%d: " fmt "\n", __FILE__,__FUNCTION__,__LINE__, ##args)
#endif

#if 1
#define UDCREG(name)
#define UDCREGL(name)
#else  /* The bugs still exists... */
#define UDCREG(name)	 serial_printf("%s():%d: %s[%08x]=%.4x\n",__FUNCTION__,__LINE__, (#name), name, inw(name))	/* For 16-bit regs */
#define UDCREGL(name)	 serial_printf("%s():%d: %s[%08x]=%.8x\n",__FUNCTION__,__LINE__, (#name), name, inl(name))	/* For 32-bit regs */
#endif


static struct urb *ep0_urb = NULL;

static struct usb_device_instance *udc_device;	/* Used in interrupt handler */
static u16 udc_devstat = 0;	/* UDC status (DEVSTAT) */
static u32 udc_interrupts = 0;

static void udc_stall_ep (unsigned int ep_addr);


static struct usb_endpoint_instance *omap1510_find_ep (int ep)
{
	int i;

	for (i = 0; i < udc_device->bus->max_endpoints; i++) {
		if (udc_device->bus->endpoint_array[i].endpoint_address == ep)
			return &udc_device->bus->endpoint_array[i];
	}
	return NULL;
}

/* ************************************************************************** */
/* IO
 */

/*
 * omap1510_prepare_endpoint_for_rx
 *
 * This function implements TRM Figure 14-11.
 *
 * The endpoint to prepare for transfer is specified as a physical endpoint
 * number.  For OUT (rx) endpoints 1 through 15, the corresponding endpoint
 * configuration register is checked to see if the endpoint is ISO or not.
 * If the OUT endpoint is valid and is non-ISO then its FIFO is enabled.
 * No action is taken for endpoint 0 or for IN (tx) endpoints 16 through 30.
 */
static void omap1510_prepare_endpoint_for_rx (int ep_addr)
{
	int ep_num = ep_addr & USB_ENDPOINT_NUMBER_MASK;

	UDCDBGA ("omap1510_prepare_endpoint %x", ep_addr);
	if (((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT)) {
		if ((inw (UDC_EP_RX (ep_num)) &
		     (UDC_EPn_RX_Valid | UDC_EPn_RX_Iso)) ==
		    UDC_EPn_RX_Valid) {
			/* rx endpoint is valid, non-ISO, so enable its FIFO */
			outw (UDC_EP_Sel | ep_num, UDC_EP_NUM);
			outw (UDC_Set_FIFO_En, UDC_CTRL);
			outw (0, UDC_EP_NUM);
		}
	}
}

/* omap1510_configure_endpoints
 *
 * This function implements TRM Figure 14-10.
 */
static void omap1510_configure_endpoints (struct usb_device_instance *device)
{
	int ep;
	struct usb_bus_instance *bus;
	struct usb_endpoint_instance *endpoint;
	unsigned short ep_ptr;
	unsigned short ep_size;
	unsigned short ep_isoc;
	unsigned short ep_doublebuffer;
	int ep_addr;
	int packet_size;
	int buffer_size;
	int attributes;

	bus = device->bus;

	/* There is a dedicated 2048 byte buffer for USB packets that may be
	 * arbitrarily partitioned among the endpoints on 8-byte boundaries.
	 * The first 8 bytes are reserved for receiving setup packets on
	 * endpoint 0.
	 */
	ep_ptr = 8;		/* reserve the first 8 bytes for the setup fifo */

	for (ep = 0; ep < bus->max_endpoints; ep++) {
		endpoint = bus->endpoint_array + ep;
		ep_addr = endpoint->endpoint_address;
		if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) {
			/* IN endpoint */
			packet_size = endpoint->tx_packetSize;
			attributes = endpoint->tx_attributes;
		} else {
			/* OUT endpoint */
			packet_size = endpoint->rcv_packetSize;
			attributes = endpoint->rcv_attributes;
		}

		switch (packet_size) {
		case 0:
			ep_size = 0;
			break;
		case 8:
			ep_size = 0;
			break;
		case 16:
			ep_size = 1;
			break;
		case 32:
			ep_size = 2;
			break;
		case 64:
			ep_size = 3;
			break;
		case 128:
			ep_size = 4;
			break;
		case 256:
			ep_size = 5;
			break;
		case 512:
			ep_size = 6;
			break;
		default:
			UDCDBGA ("ep 0x%02x has bad packet size %d",
				 ep_addr, packet_size);
			packet_size = 0;
			ep_size = 0;
			break;
		}

		switch (attributes & USB_ENDPOINT_XFERTYPE_MASK) {
		case USB_ENDPOINT_XFER_CONTROL:
		case USB_ENDPOINT_XFER_BULK:
		case USB_ENDPOINT_XFER_INT:
		default:
			/* A non-isochronous endpoint may optionally be
			 * double-buffered. For now we disable
			 * double-buffering.
			 */
			ep_doublebuffer = 0;
			ep_isoc = 0;
			if (packet_size > 64)
				packet_size = 0;
			if (!ep || !ep_doublebuffer)
				buffer_size = packet_size;
			else
				buffer_size = packet_size * 2;
			break;
		case USB_ENDPOINT_XFER_ISOC:
			/* Isochronous endpoints are always double-
			 * buffered, but the double-buffering bit
			 * in the endpoint configuration register
			 * becomes the msb of the endpoint size so we
			 * set the double-buffering flag to zero.
			 */
			ep_doublebuffer = 0;
			ep_isoc = 1;
			buffer_size = packet_size * 2;
			break;
		}

		/* check to see if our packet buffer RAM is exhausted */
		if ((ep_ptr + buffer_size) > 2048) {
			UDCDBGA ("out of packet RAM for ep 0x%02x buf size %d", ep_addr, buffer_size);
			buffer_size = packet_size = 0;
		}

		/* force a default configuration for endpoint 0 since it is
		 * always enabled
		 */
		if (!ep && ((packet_size < 8) || (packet_size > 64))) {
			buffer_size = packet_size = 64;
			ep_size = 3;
		}

		if (!ep) {
			/* configure endpoint 0 */
			outw ((ep_size << 12) | (ep_ptr >> 3), UDC_EP0);
			/*UDCDBGA("ep 0 buffer offset 0x%03x packet size 0x%03x", */
			/*	ep_ptr, packet_size); */
		} else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) {
			/* IN endpoint */
			if (packet_size) {
				outw ((1 << 15) | (ep_doublebuffer << 14) |
				      (ep_size << 12) | (ep_isoc << 11) |
				      (ep_ptr >> 3),
				      UDC_EP_TX (ep_addr &
						 USB_ENDPOINT_NUMBER_MASK));
				UDCDBGA ("IN ep %d buffer offset 0x%03x"
					 " packet size 0x%03x",
					 ep_addr & USB_ENDPOINT_NUMBER_MASK,
					 ep_ptr, packet_size);
			} else {
				outw (0,
				      UDC_EP_TX (ep_addr &
						 USB_ENDPOINT_NUMBER_MASK));
			}
		} else {
			/* OUT endpoint */
			if (packet_size) {
				outw ((1 << 15) | (ep_doublebuffer << 14) |
				      (ep_size << 12) | (ep_isoc << 11) |
				      (ep_ptr >> 3),
				      UDC_EP_RX (ep_addr &
						 USB_ENDPOINT_NUMBER_MASK));
				UDCDBGA ("OUT ep %d buffer offset 0x%03x"
					 " packet size 0x%03x",
					 ep_addr & USB_ENDPOINT_NUMBER_MASK,
					 ep_ptr, packet_size);
			} else {
				outw (0,
				      UDC_EP_RX (ep_addr &
						 USB_ENDPOINT_NUMBER_MASK));
			}
		}
		ep_ptr += buffer_size;
	}
}

/* omap1510_deconfigure_device
 *
 * This function balances omap1510_configure_device.
 */
static void omap1510_deconfigure_device (void)
{
	int epnum;

	UDCDBG ("clear Cfg_Lock");
	outw (inw (UDC_SYSCON1) & ~UDC_Cfg_Lock, UDC_SYSCON1);
	UDCREG (UDC_SYSCON1);

	/* deconfigure all endpoints */
	for (epnum = 1; epnum <= 15; epnum++) {
		outw (0, UDC_EP_RX (epnum));
		outw (0, UDC_EP_TX (epnum));
	}
}

/* omap1510_configure_device
 *
 * This function implements TRM Figure 14-9.
 */
static void omap1510_configure_device (struct usb_device_instance *device)
{
	omap1510_configure_endpoints (device);


	/* Figure 14-9 indicates we should enable interrupts here, but we have
	 * other routines (udc_all_interrupts, udc_suspended_interrupts) to
	 * do that.
	 */

	UDCDBG ("set Cfg_Lock");
	outw (inw (UDC_SYSCON1) | UDC_Cfg_Lock, UDC_SYSCON1);
	UDCREG (UDC_SYSCON1);
}

/* omap1510_write_noniso_tx_fifo
 *
 * This function implements TRM Figure 14-30.
 *
 * If the endpoint has an active tx_urb, then the next packet of data from the
 * URB is written to the tx FIFO.  The total amount of data in the urb is given
 * by urb->actual_length.  The maximum amount of data that can be sent in any
 * one packet is given by endpoint->tx_packetSize.  The number of data bytes
 * from this URB that have already been transmitted is given by endpoint->sent.
 * endpoint->last is updated by this routine with the number of data bytes
 * transmitted in this packet.
 *
 * In accordance with Figure 14-30, the EP_NUM register must already have been
 * written with the value to select the appropriate tx FIFO before this routine
 * is called.
 */
static void omap1510_write_noniso_tx_fifo (struct usb_endpoint_instance
					   *endpoint)
{
	struct urb *urb = endpoint->tx_urb;

	if (urb) {
		unsigned int last, i;

		UDCDBGA ("urb->buffer %p, buffer_length %d, actual_length %d",
			 urb->buffer, urb->buffer_length, urb->actual_length);
		if ((last =
		     MIN (urb->actual_length - endpoint->sent,
			  endpoint->tx_packetSize))) {
			u8 *cp = urb->buffer + endpoint->sent;

			UDCDBGA ("endpoint->sent %d, tx_packetSize %d, last %d", endpoint->sent, endpoint->tx_packetSize, last);

			if (((u32) cp & 1) == 0) {	/* word aligned? */
				outsw (UDC_DATA, cp, last >> 1);
			} else {	/* byte aligned. */
				for (i = 0; i < (last >> 1); i++) {
					u16 w = ((u16) cp[2 * i + 1] << 8) |
						(u16) cp[2 * i];
					outw (w, UDC_DATA);
				}
			}
			if (last & 1) {
				outb (*(cp + last - 1), UDC_DATA);
			}
		}
		endpoint->last = last;
	}
}

/* omap1510_read_noniso_rx_fifo
 *
 * This function implements TRM Figure 14-28.
 *
 * If the endpoint has an active rcv_urb, then the next packet of data is read
 * from the rcv FIFO and written to rcv_urb->buffer at offset
 * rcv_urb->actual_length to append the packet data to the data from any
 * previous packets for this transfer.	We assume that there is sufficient room
 * left in the buffer to hold an entire packet of data.
 *
 * The return value is the number of bytes read from the FIFO for this packet.
 *
 * In accordance with Figure 14-28, the EP_NUM register must already have been
 * written with the value to select the appropriate rcv FIFO before this routine
 * is called.
 */
static int omap1510_read_noniso_rx_fifo (struct usb_endpoint_instance
					 *endpoint)
{
	struct urb *urb = endpoint->rcv_urb;
	int len = 0;

	if (urb) {
		len = inw (UDC_RXFSTAT);

		if (len) {
			unsigned char *cp = urb->buffer + urb->actual_length;

			insw (UDC_DATA, cp, len >> 1);
			if (len & 1)
				*(cp + len - 1) = inb (UDC_DATA);
		}
	}
	return len;
}

/* omap1510_prepare_for_control_write_status
 *
 * This function implements TRM Figure 14-17.
 *
 * We have to deal here with non-autodecoded control writes that haven't already
 * been dealt with by ep0_recv_setup.  The non-autodecoded standard control
 * write requests are:	set/clear endpoint feature, set configuration, set
 * interface, and set descriptor.  ep0_recv_setup handles set/clear requests for
 * ENDPOINT_HALT by halting the endpoint for a set request and resetting the
 * endpoint for a clear request.  ep0_recv_setup returns an error for
 * SET_DESCRIPTOR requests which causes them to be terminated with a stall by
 * the setup handler.  A SET_INTERFACE request is handled by ep0_recv_setup by
 * generating a DEVICE_SET_INTERFACE event.  This leaves only the
 * SET_CONFIGURATION event for us to deal with here.
 *
 */
static void omap1510_prepare_for_control_write_status (struct urb *urb)
{
	struct usb_device_request *request = &urb->device_request;;

	/* check for a SET_CONFIGURATION request */
	if (request->bRequest == USB_REQ_SET_CONFIGURATION) {
		int configuration = le16_to_cpu (request->wValue) & 0xff;
		unsigned short devstat = inw (UDC_DEVSTAT);

		if ((devstat & (UDC_ADD | UDC_CFG)) == UDC_ADD) {
			/* device is currently in ADDRESSED state */
			if (configuration) {
				/* Assume the specified non-zero configuration
				 * value is valid and switch to the CONFIGURED
				 * state.
				 */
				outw (UDC_Dev_Cfg, UDC_SYSCON2);
			}
		} else if ((devstat & UDC_CFG) == UDC_CFG) {
			/* device is currently in CONFIGURED state */
			if (!configuration) {
				/* Switch to ADDRESSED state. */
				outw (UDC_Clr_Cfg, UDC_SYSCON2);
			}
		}
	}

	/* select EP0 tx FIFO */
	outw (UDC_EP_Dir | UDC_EP_Sel, UDC_EP_NUM);
	/* clear endpoint (no data bytes in status stage) */
	outw (UDC_Clr_EP, UDC_CTRL);
	/* enable the EP0 tx FIFO */
	outw (UDC_Set_FIFO_En, UDC_CTRL);
	/* deselect the endpoint */
	outw (UDC_EP_Dir, UDC_EP_NUM);
}

/* udc_state_transition_up
 * udc_state_transition_down
 *
 * Helper functions to implement device state changes.	The device states and
 * the events that transition between them are:
 *
 *				STATE_ATTACHED
 *				||	/\
 *				\/	||
 *	DEVICE_HUB_CONFIGURED			DEVICE_HUB_RESET
 *				||	/\
 *				\/	||
 *				STATE_POWERED
 *				||	/\
 *				\/	||
 *	DEVICE_RESET				DEVICE_POWER_INTERRUPTION
 *				||	/\
 *				\/	||
 *				STATE_DEFAULT
 *				||	/\
 *				\/	||
 *	DEVICE_ADDRESS_ASSIGNED			DEVICE_RESET
 *				||	/\
 *				\/	||
 *				STATE_ADDRESSED
 *				||	/\
 *				\/	||
 *	DEVICE_CONFIGURED			DEVICE_DE_CONFIGURED
 *				||	/\
 *				\/	||
 *				STATE_CONFIGURED
 *
 * udc_state_transition_up transitions up (in the direction from STATE_ATTACHED
 * to STATE_CONFIGURED) from the specified initial state to the specified final
 * state, passing through each intermediate state on the way.  If the initial
 * state is at or above (i.e. nearer to STATE_CONFIGURED) the final state, then
 * no state transitions will take place.
 *
 * udc_state_transition_down transitions down (in the direction from
 * STATE_CONFIGURED to STATE_ATTACHED) from the specified initial state to the
 * specified final state, passing through each intermediate state on the way.
 * If the initial state is at or below (i.e. nearer to STATE_ATTACHED) the final
 * state, then no state transitions will take place.
 *
 * These functions must only be called with interrupts disabled.
 */
static void udc_state_transition_up (usb_device_state_t initial,
				     usb_device_state_t final)
{
	if (initial < final) {
		switch (initial) {
		case STATE_ATTACHED:
			usbd_device_event_irq (udc_device,
					       DEVICE_HUB_CONFIGURED, 0);
			if (final == STATE_POWERED)
				break;
		case STATE_POWERED:
			usbd_device_event_irq (udc_device, DEVICE_RESET, 0);
			if (final == STATE_DEFAULT)
				break;
		case STATE_DEFAULT:
			usbd_device_event_irq (udc_device,
					       DEVICE_ADDRESS_ASSIGNED, 0);
			if (final == STATE_ADDRESSED)
				break;
		case STATE_ADDRESSED:
			usbd_device_event_irq (udc_device, DEVICE_CONFIGURED,
					       0);
		case STATE_CONFIGURED:
			break;
		default:
			break;
		}
	}
}

static void udc_state_transition_down (usb_device_state_t initial,
				       usb_device_state_t final)
{
	if (initial > final) {
		switch (initial) {
		case STATE_CONFIGURED:
			usbd_device_event_irq (udc_device, DEVICE_DE_CONFIGURED, 0);
			if (final == STATE_ADDRESSED)
				break;
		case STATE_ADDRESSED:
			usbd_device_event_irq (udc_device, DEVICE_RESET, 0);
			if (final == STATE_DEFAULT)
				break;
		case STATE_DEFAULT:
			usbd_device_event_irq (udc_device, DEVICE_POWER_INTERRUPTION, 0);
			if (final == STATE_POWERED)
				break;
		case STATE_POWERED:
			usbd_device_event_irq (udc_device, DEVICE_HUB_RESET, 0);
		case STATE_ATTACHED:
			break;
		default:
			break;
		}
	}
}

/* Handle all device state changes.
 * This function implements TRM Figure 14-21.
 */
static void omap1510_udc_state_changed (void)
{
	u16 bits;
	u16 devstat = inw (UDC_DEVSTAT);

	UDCDBGA ("state changed, devstat %x, old %x", devstat, udc_devstat);

	bits = devstat ^ udc_devstat;
	if (bits) {
		if (bits & UDC_ATT) {
			if (devstat & UDC_ATT) {
				UDCDBG ("device attached and powered");
				udc_state_transition_up (udc_device->device_state, STATE_POWERED);
			} else {
				UDCDBG ("device detached or unpowered");
				udc_state_transition_down (udc_device->device_state, STATE_ATTACHED);
			}
		}
		if (bits & UDC_USB_Reset) {
			if (devstat & UDC_USB_Reset) {
				UDCDBG ("device reset in progess");
				udc_state_transition_down (udc_device->device_state, STATE_POWERED);
			} else {
				UDCDBG ("device reset completed");
			}
		}
		if (bits & UDC_DEF) {
			if (devstat & UDC_DEF) {
				UDCDBG ("device entering default state");
				udc_state_transition_up (udc_device->device_state, STATE_DEFAULT);
			} else {
				UDCDBG ("device leaving default state");
				udc_state_transition_down (udc_device->device_state, STATE_POWERED);
			}
		}
		if (bits & UDC_SUS) {
			if (devstat & UDC_SUS) {
				UDCDBG ("entering suspended state");
				usbd_device_event_irq (udc_device, DEVICE_BUS_INACTIVE, 0);
			} else {
				UDCDBG ("leaving suspended state");
				usbd_device_event_irq (udc_device, DEVICE_BUS_ACTIVITY, 0);
			}
		}
		if (bits & UDC_R_WK_OK) {
			UDCDBGA ("remote wakeup %s", (devstat & UDC_R_WK_OK)
				 ? "enabled" : "disabled");
		}
		if (bits & UDC_ADD) {
			if (devstat & UDC_ADD) {
				UDCDBG ("default -> addressed");
				udc_state_transition_up (udc_device->device_state, STATE_ADDRESSED);
			} else {
				UDCDBG ("addressed -> default");
				udc_state_transition_down (udc_device->device_state, STATE_DEFAULT);
			}
		}
		if (bits & UDC_CFG) {
			if (devstat & UDC_CFG) {
				UDCDBG ("device configured");
				/* The ep0_recv_setup function generates the
				 * DEVICE_CONFIGURED event when a
				 * USB_REQ_SET_CONFIGURATION setup packet is
				 * received, so we should already be in the
				 * state STATE_CONFIGURED.
				 */
				udc_state_transition_up (udc_device->device_state, STATE_CONFIGURED);
			} else {
				UDCDBG ("device deconfigured");
				udc_state_transition_down (udc_device->device_state, STATE_ADDRESSED);
			}
		}
	}

	/* Clear interrupt source */
	outw (UDC_DS_Chg, UDC_IRQ_SRC);

	/* Save current DEVSTAT */
	udc_devstat = devstat;
}

/* Handle SETUP USB interrupt.
 * This function implements TRM Figure 14-14.
 */
static void omap1510_udc_setup (struct usb_endpoint_instance *endpoint)
{
	UDCDBG ("-> Entering device setup");

	do {
		const int setup_pktsize = 8;
		unsigned char *datap =
			(unsigned char *) &ep0_urb->device_request;

		/* Gain access to EP 0 setup FIFO */
		outw (UDC_Setup_Sel, UDC_EP_NUM);

		/* Read control request data */
		insb (UDC_DATA, datap, setup_pktsize);

		UDCDBGA ("EP0 setup read [%x %x %x %x %x %x %x %x]",
			 *(datap + 0), *(datap + 1), *(datap + 2),
			 *(datap + 3), *(datap + 4), *(datap + 5),
			 *(datap + 6), *(datap + 7));

		/* Reset EP0 setup FIFO */
		outw (0, UDC_EP_NUM);
	} while (inw (UDC_IRQ_SRC) & UDC_Setup);

	/* Try to process setup packet */
	if (ep0_recv_setup (ep0_urb)) {
		/* Not a setup packet, stall next EP0 transaction */
		udc_stall_ep (0);
		UDCDBG ("can't parse setup packet, still waiting for setup");
		return;
	}

	/* Check direction */
	if ((ep0_urb->device_request.bmRequestType & USB_REQ_DIRECTION_MASK)
	    == USB_REQ_HOST2DEVICE) {
		UDCDBG ("control write on EP0");
		if (le16_to_cpu (ep0_urb->device_request.wLength)) {
			/* We don't support control write data stages.
			 * The only standard control write request with a data
			 * stage is SET_DESCRIPTOR, and ep0_recv_setup doesn't
			 * support that so we just stall those requests.  A
			 * function driver might support a non-standard
			 * write request with a data stage, but it isn't
			 * obvious what we would do with the data if we read it
			 * so we'll just stall it.  It seems like the API isn't
			 * quite right here.
			 */
#if 0
			/* Here is what we would do if we did support control
			 * write data stages.
			 */
			ep0_urb->actual_length = 0;
			outw (0, UDC_EP_NUM);
			/* enable the EP0 rx FIFO */
			outw (UDC_Set_FIFO_En, UDC_CTRL);
#else
			/* Stall this request */
			UDCDBG ("Stalling unsupported EP0 control write data "
				"stage.");
			udc_stall_ep (0);
#endif
		} else {
			omap1510_prepare_for_control_write_status (ep0_urb);
		}
	} else {
		UDCDBG ("control read on EP0");
		/* The ep0_recv_setup function has already placed our response
		 * packet data in ep0_urb->buffer and the packet length in
		 * ep0_urb->actual_length.
		 */
		endpoint->tx_urb = ep0_urb;
		endpoint->sent = 0;
		/* select the EP0 tx FIFO */
		outw (UDC_EP_Dir | UDC_EP_Sel, UDC_EP_NUM);
		/* Write packet data to the FIFO.  omap1510_write_noniso_tx_fifo
		 * will update endpoint->last with the number of bytes written
		 * to the FIFO.
		 */
		omap1510_write_noniso_tx_fifo (endpoint);
		/* enable the FIFO to start the packet transmission */
		outw (UDC_Set_FIFO_En, UDC_CTRL);
		/* deselect the EP0 tx FIFO */
		outw (UDC_EP_Dir, UDC_EP_NUM);
	}

	UDCDBG ("<- Leaving device setup");
}

/* Handle endpoint 0 RX interrupt
 * This routine implements TRM Figure 14-16.
 */
static void omap1510_udc_ep0_rx (struct usb_endpoint_instance *endpoint)
{
	unsigned short status;

	UDCDBG ("RX on EP0");
	/* select EP0 rx FIFO */
	outw (UDC_EP_Sel, UDC_EP_NUM);

	status = inw (UDC_STAT_FLG);

	if (status & UDC_ACK) {
		/* Check direction */
		if ((ep0_urb->device_request.bmRequestType
		     & USB_REQ_DIRECTION_MASK) == USB_REQ_HOST2DEVICE) {
			/* This rx interrupt must be for a control write data
			 * stage packet.
			 *
			 * We don't support control write data stages.
			 * We should never end up here.
			 */

			/* clear the EP0 rx FIFO */
			outw (UDC_Clr_EP, UDC_CTRL);

			/* deselect the EP0 rx FIFO */
			outw (0, UDC_EP_NUM);

			UDCDBG ("Stalling unexpected EP0 control write "
				"data stage packet");
			udc_stall_ep (0);
		} else {
			/* This rx interrupt must be for a control read status
			 * stage packet.
			 */
			UDCDBG ("ACK on EP0 control read status stage packet");
			/* deselect EP0 rx FIFO */
			outw (0, UDC_EP_NUM);
		}
	} else if (status & UDC_STALL) {
		UDCDBG ("EP0 stall during RX");
		/* deselect EP0 rx FIFO */
		outw (0, UDC_EP_NUM);
	} else {
		/* deselect EP0 rx FIFO */
		outw (0, UDC_EP_NUM);
	}
}

/* Handle endpoint 0 TX interrupt
 * This routine implements TRM Figure 14-18.
 */
static void omap1510_udc_ep0_tx (struct usb_endpoint_instance *endpoint)
{
	unsigned short status;
	struct usb_device_request *request = &ep0_urb->device_request;

	UDCDBG ("TX on EP0");
	/* select EP0 TX FIFO */
	outw (UDC_EP_Dir | UDC_EP_Sel, UDC_EP_NUM);

	status = inw (UDC_STAT_FLG);
	if (status & UDC_ACK) {
		/* Check direction */
		if ((request->bmRequestType & USB_REQ_DIRECTION_MASK) ==
		    USB_REQ_HOST2DEVICE) {
			/* This tx interrupt must be for a control write status
			 * stage packet.
			 */
			UDCDBG ("ACK on EP0 control write status stage packet");
			/* deselect EP0 TX FIFO */
			outw (UDC_EP_Dir, UDC_EP_NUM);
		} else {
			/* This tx interrupt must be for a control read data
			 * stage packet.
			 */
			int wLength = le16_to_cpu (request->wLength);

			/* Update our count of bytes sent so far in this
			 * transfer.
			 */
			endpoint->sent += endpoint->last;

			/* We are finished with this transfer if we have sent
			 * all of the bytes in our tx urb (urb->actual_length)
			 * unless we need a zero-length terminating packet.  We
			 * need a zero-length terminating packet if we returned
			 * fewer bytes than were requested (wLength) by the host,
			 * and the number of bytes we returned is an exact
			 * multiple of the packet size endpoint->tx_packetSize.
			 */
			if ((endpoint->sent == ep0_urb->actual_length)
			    && ((ep0_urb->actual_length == wLength)
				|| (endpoint->last !=
				    endpoint->tx_packetSize))) {
				/* Done with control read data stage. */
				UDCDBG ("control read data stage complete");
				/* deselect EP0 TX FIFO */
				outw (UDC_EP_Dir, UDC_EP_NUM);
				/* select EP0 RX FIFO to prepare for control
				 * read status stage.
				 */
				outw (UDC_EP_Sel, UDC_EP_NUM);
				/* clear the EP0 RX FIFO */
				outw (UDC_Clr_EP, UDC_CTRL);
				/* enable the EP0 RX FIFO */
				outw (UDC_Set_FIFO_En, UDC_CTRL);
				/* deselect the EP0 RX FIFO */
				outw (0, UDC_EP_NUM);
			} else {
				/* We still have another packet of data to send
				 * in this control read data stage or else we
				 * need a zero-length terminating packet.
				 */
				UDCDBG ("ACK control read data stage packet");
				omap1510_write_noniso_tx_fifo (endpoint);
				/* enable the EP0 tx FIFO to start transmission */
				outw (UDC_Set_FIFO_En, UDC_CTRL);
				/* deselect EP0 TX FIFO */
				outw (UDC_EP_Dir, UDC_EP_NUM);
			}
		}
	} else if (status & UDC_STALL) {
		UDCDBG ("EP0 stall during TX");
		/* deselect EP0 TX FIFO */
		outw (UDC_EP_Dir, UDC_EP_NUM);
	} else {
		/* deselect EP0 TX FIFO */
		outw (UDC_EP_Dir, UDC_EP_NUM);
	}
}

/* Handle RX transaction on non-ISO endpoint.
 * This function implements TRM Figure 14-27.
 * The ep argument is a physical endpoint number for a non-ISO OUT endpoint
 * in the range 1 to 15.
 */
static void omap1510_udc_epn_rx (int ep)
{
	unsigned short status;

	/* Check endpoint status */
	status = inw (UDC_STAT_FLG);

	if (status & UDC_ACK) {
		int nbytes;
		struct usb_endpoint_instance *endpoint =
			omap1510_find_ep (ep);

		nbytes = omap1510_read_noniso_rx_fifo (endpoint);
		usbd_rcv_complete (endpoint, nbytes, 0);

		/* enable rx FIFO to prepare for next packet */
		outw (UDC_Set_FIFO_En, UDC_CTRL);
	} else if (status & UDC_STALL) {
		UDCDBGA ("STALL on RX endpoint %d", ep);
	} else if (status & UDC_NAK) {
		UDCDBGA ("NAK on RX ep %d", ep);
	} else {
		serial_printf ("omap-bi: RX on ep %d with status %x", ep,
			       status);
	}
}

/* Handle TX transaction on non-ISO endpoint.
 * This function implements TRM Figure 14-29.
 * The ep argument is a physical endpoint number for a non-ISO IN endpoint
 * in the range 16 to 30.
 */
static void omap1510_udc_epn_tx (int ep)
{
	unsigned short status;

	/*serial_printf("omap1510_udc_epn_tx( %x )\n",ep); */

	/* Check endpoint status */
	status = inw (UDC_STAT_FLG);

	if (status & UDC_ACK) {
		struct usb_endpoint_instance *endpoint =
			omap1510_find_ep (ep);

		/* We need to transmit a terminating zero-length packet now if
		 * we have sent all of the data in this URB and the transfer
		 * size was an exact multiple of the packet size.
		 */
		if (endpoint->tx_urb
		    && (endpoint->last == endpoint->tx_packetSize)
		    && (endpoint->tx_urb->actual_length - endpoint->sent -
			endpoint->last == 0)) {
			/* Prepare to transmit a zero-length packet. */
			endpoint->sent += endpoint->last;
			/* write 0 bytes of data to FIFO */
			omap1510_write_noniso_tx_fifo (endpoint);
			/* enable tx FIFO to start transmission */
			outw (UDC_Set_FIFO_En, UDC_CTRL);
		} else if (endpoint->tx_urb
			   && endpoint->tx_urb->actual_length) {
			/* retire the data that was just sent */
			usbd_tx_complete (endpoint);
			/* Check to see if we have more data ready to transmit
			 * now.
			 */
			if (endpoint->tx_urb
			    && endpoint->tx_urb->actual_length) {
				/* write data to FIFO */
				omap1510_write_noniso_tx_fifo (endpoint);
				/* enable tx FIFO to start transmission */
				outw (UDC_Set_FIFO_En, UDC_CTRL);
			}
		}
	} else if (status & UDC_STALL) {
		UDCDBGA ("STALL on TX endpoint %d", ep);
	} else if (status & UDC_NAK) {
		UDCDBGA ("NAK on TX endpoint %d", ep);
	} else {
		/*serial_printf("omap-bi: TX on ep %d with status %x\n", ep, status); */
	}
}


/*
-------------------------------------------------------------------------------
*/

/* Handle general USB interrupts and dispatch according to type.
 * This function implements TRM Figure 14-13.
 */
void omap1510_udc_irq (void)
{
	u16 irq_src = inw (UDC_IRQ_SRC);
	int valid_irq = 0;

	if (!(irq_src & ~UDC_SOF_Flg))	/* ignore SOF interrupts ) */
		return;

	UDCDBGA ("< IRQ #%d start >- %x", udc_interrupts, irq_src);
	/*serial_printf("< IRQ #%d start >- %x\n", udc_interrupts, irq_src); */

	if (irq_src & UDC_DS_Chg) {
		/* Device status changed */
		omap1510_udc_state_changed ();
		valid_irq++;
	}
	if (irq_src & UDC_EP0_RX) {
		/* Endpoint 0 receive */
		outw (UDC_EP0_RX, UDC_IRQ_SRC); /* ack interrupt */
		omap1510_udc_ep0_rx (udc_device->bus->endpoint_array + 0);
		valid_irq++;
	}
	if (irq_src & UDC_EP0_TX) {
		/* Endpoint 0 transmit */
		outw (UDC_EP0_TX, UDC_IRQ_SRC); /* ack interrupt */
		omap1510_udc_ep0_tx (udc_device->bus->endpoint_array + 0);
		valid_irq++;
	}
	if (irq_src & UDC_Setup) {
		/* Device setup */
		omap1510_udc_setup (udc_device->bus->endpoint_array + 0);
		valid_irq++;
	}
	/*if (!valid_irq) */
	/*	serial_printf("unknown interrupt, IRQ_SRC %.4x\n", irq_src); */
	UDCDBGA ("< IRQ #%d end >", udc_interrupts);
	udc_interrupts++;
}

/* This function implements TRM Figure 14-26. */
void omap1510_udc_noniso_irq (void)
{
	unsigned short epnum;
	unsigned short irq_src = inw (UDC_IRQ_SRC);
	int valid_irq = 0;

	if (!(irq_src & (UDC_EPn_RX | UDC_EPn_TX)))
		return;

	UDCDBGA ("non-ISO IRQ, IRQ_SRC %x", inw (UDC_IRQ_SRC));

	if (irq_src & UDC_EPn_RX) {	/* Endpoint N OUT transaction */
		/* Determine the endpoint number for this interrupt */
		epnum = (inw (UDC_EPN_STAT) & 0x0f00) >> 8;
		UDCDBGA ("RX on ep %x", epnum);

		/* acknowledge interrupt */
		outw (UDC_EPn_RX, UDC_IRQ_SRC);

		if (epnum) {
			/* select the endpoint FIFO */
			outw (UDC_EP_Sel | epnum, UDC_EP_NUM);

			omap1510_udc_epn_rx (epnum);

			/* deselect the endpoint FIFO */
			outw (epnum, UDC_EP_NUM);
		}
		valid_irq++;
	}
	if (irq_src & UDC_EPn_TX) {	/* Endpoint N IN transaction */
		/* Determine the endpoint number for this interrupt */
		epnum = (inw (UDC_EPN_STAT) & 0x000f) | USB_DIR_IN;
		UDCDBGA ("TX on ep %x", epnum);

		/* acknowledge interrupt */
		outw (UDC_EPn_TX, UDC_IRQ_SRC);

		if (epnum) {
			/* select the endpoint FIFO */
			outw (UDC_EP_Sel | UDC_EP_Dir | epnum, UDC_EP_NUM);

			omap1510_udc_epn_tx (epnum);

			/* deselect the endpoint FIFO */
			outw (UDC_EP_Dir | epnum, UDC_EP_NUM);
		}
		valid_irq++;
	}
	if (!valid_irq)
		serial_printf (": unknown non-ISO interrupt, IRQ_SRC %.4x\n",
			       irq_src);
}

/*
-------------------------------------------------------------------------------
*/


/*
 * Start of public functions.
 */

/* Called to start packet transmission. */
void udc_endpoint_write (struct usb_endpoint_instance *endpoint)
{
	unsigned short epnum =
		endpoint->endpoint_address & USB_ENDPOINT_NUMBER_MASK;

	UDCDBGA ("Starting transmit on ep %x", epnum);

	if (endpoint->tx_urb) {
		/* select the endpoint FIFO */
		outw (UDC_EP_Sel | UDC_EP_Dir | epnum, UDC_EP_NUM);
		/* write data to FIFO */
		omap1510_write_noniso_tx_fifo (endpoint);
		/* enable tx FIFO to start transmission */
		outw (UDC_Set_FIFO_En, UDC_CTRL);
		/* deselect the endpoint FIFO */
		outw (UDC_EP_Dir | epnum, UDC_EP_NUM);
	}
}

/* Start to initialize h/w stuff */
int udc_init (void)
{
	u16 udc_rev;
	uchar value;

	udc_device = NULL;

	UDCDBG ("starting");

	/* Check peripheral reset. Must be 1 to make sure
	   MPU TIPB peripheral reset is inactive */
	UDCREG (ARM_RSTCT2);

	/* Set and check clock control.
	 * We might ought to be using the clock control API to do
	 * this instead of fiddling with the clock registers directly
	 * here.
	 */
	outw ((1 << 4) | (1 << 5), CLOCK_CTRL);
	UDCREG (CLOCK_CTRL);
	/* Set and check APLL */
	outw (0x0008, APLL_CTRL);
	UDCREG (APLL_CTRL);
	/* Set and check DPLL */
	outw (0x2210, DPLL_CTRL);
	UDCREG (DPLL_CTRL);
	/* Set and check SOFT */
	outw ((1 << 4) | (1 << 3) | 1, SOFT_REQ);
	/* Short delay to wait for DPLL */
	udelay (1000);

	/* Print banner with device revision */
	udc_rev = inw (UDC_REV) & 0xff;
	printf ("USB:   TI OMAP1510 USB function module rev %d.%d\n",
		udc_rev >> 4, udc_rev & 0xf);

#ifdef CONFIG_OMAP_SX1
	i2c_read (0x32, 0x04, 1, &value, 1);
	value |= 0x04;
	i2c_write (0x32, 0x04, 1, &value, 1);

	i2c_read (0x32, 0x03, 1, &value, 1);
	value |= 0x01;
	i2c_write (0x32, 0x03, 1, &value, 1);
#endif

	/* The VBUS_MODE bit selects whether VBUS detection is done via
	 * software (1) or hardware (0).  When software detection is
	 * selected, VBUS_CTRL selects whether USB is not connected (0)
	 * or connected (1).
	 */
	outl (inl (FUNC_MUX_CTRL_0) | UDC_VBUS_MODE, FUNC_MUX_CTRL_0);
	outl (inl (FUNC_MUX_CTRL_0) & ~UDC_VBUS_CTRL, FUNC_MUX_CTRL_0);
	UDCREGL (FUNC_MUX_CTRL_0);

	/*
	 * At this point, device is ready for configuration...
	 */

	UDCDBG ("disable USB interrupts");
	outw (0, UDC_IRQ_EN);
	UDCREG (UDC_IRQ_EN);

	UDCDBG ("disable USB DMA");
	outw (0, UDC_DMA_IRQ_EN);
	UDCREG (UDC_DMA_IRQ_EN);

	UDCDBG ("initialize SYSCON1");
	outw (UDC_Self_Pwr | UDC_Pullup_En, UDC_SYSCON1);
	UDCREG (UDC_SYSCON1);

	return 0;
}

/* Stall endpoint */
static void udc_stall_ep (unsigned int ep_addr)
{
	/*int ep_addr = PHYS_EP_TO_EP_ADDR(ep); */
	int ep_num = ep_addr & USB_ENDPOINT_NUMBER_MASK;

	UDCDBGA ("stall ep_addr %d", ep_addr);

	/* REVISIT?
	 * The OMAP TRM section 14.2.4.2 says we must check that the FIFO
	 * is empty before halting the endpoint.  The current implementation
	 * doesn't check that the FIFO is empty.
	 */

	if (!ep_num) {
		outw (UDC_Stall_Cmd, UDC_SYSCON2);
	} else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT) {
		if (inw (UDC_EP_RX (ep_num)) & UDC_EPn_RX_Valid) {
			/* we have a valid rx endpoint, so halt it */
			outw (UDC_EP_Sel | ep_num, UDC_EP_NUM);
			outw (UDC_Set_Halt, UDC_CTRL);
			outw (ep_num, UDC_EP_NUM);
		}
	} else {
		if (inw (UDC_EP_TX (ep_num)) & UDC_EPn_TX_Valid) {
			/* we have a valid tx endpoint, so halt it */
			outw (UDC_EP_Sel | UDC_EP_Dir | ep_num, UDC_EP_NUM);
			outw (UDC_Set_Halt, UDC_CTRL);
			outw (ep_num, UDC_EP_NUM);
		}
	}
}

/* Reset endpoint */
#if 0
static void udc_reset_ep (unsigned int ep_addr)
{
	/*int ep_addr = PHYS_EP_TO_EP_ADDR(ep); */
	int ep_num = ep_addr & USB_ENDPOINT_NUMBER_MASK;

	UDCDBGA ("reset ep_addr %d", ep_addr);

	if (!ep_num) {
		/* control endpoint 0 can't be reset */
	} else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT) {
		UDCDBGA ("UDC_EP_RX(%d) = 0x%04x", ep_num,
			 inw (UDC_EP_RX (ep_num)));
		if (inw (UDC_EP_RX (ep_num)) & UDC_EPn_RX_Valid) {
			/* we have a valid rx endpoint, so reset it */
			outw (ep_num | UDC_EP_Sel, UDC_EP_NUM);
			outw (UDC_Reset_EP, UDC_CTRL);
			outw (ep_num, UDC_EP_NUM);
			UDCDBGA ("OUT endpoint %d reset", ep_num);
		}
	} else {
		UDCDBGA ("UDC_EP_TX(%d) = 0x%04x", ep_num,
			 inw (UDC_EP_TX (ep_num)));
		/* Resetting of tx endpoints seems to be causing the USB function
		 * module to fail, which causes problems when the driver is
		 * uninstalled.	 We'll skip resetting tx endpoints for now until
		 * we figure out what the problem is.
		 */
#if 0
		if (inw (UDC_EP_TX (ep_num)) & UDC_EPn_TX_Valid) {
			/* we have a valid tx endpoint, so reset it */
			outw (ep_num | UDC_EP_Dir | UDC_EP_Sel, UDC_EP_NUM);
			outw (UDC_Reset_EP, UDC_CTRL);
			outw (ep_num | UDC_EP_Dir, UDC_EP_NUM);
			UDCDBGA ("IN endpoint %d reset", ep_num);
		}
#endif
	}
}
#endif

/* ************************************************************************** */

/**
 * udc_check_ep - check logical endpoint
  *
 * Return physical endpoint number to use for this logical endpoint or zero if not valid.
 */
#if 0
int udc_check_ep (int logical_endpoint, int packetsize)
{
	if ((logical_endpoint == 0x80) ||
	    ((logical_endpoint & 0x8f) != logical_endpoint)) {
		return 0;
	}

	switch (packetsize) {
	case 8:
	case 16:
	case 32:
	case 64:
	case 128:
	case 256:
	case 512:
		break;
	default:
		return 0;
	}

	return EP_ADDR_TO_PHYS_EP (logical_endpoint);
}
#endif

/*
 * udc_setup_ep - setup endpoint
 *
 * Associate a physical endpoint with endpoint_instance
 */
void udc_setup_ep (struct usb_device_instance *device,
		   unsigned int ep, struct usb_endpoint_instance *endpoint)
{
	UDCDBGA ("setting up endpoint addr %x", endpoint->endpoint_address);

	/* This routine gets called by bi_modinit for endpoint 0 and from
	 * bi_config for all of the other endpoints.  bi_config gets called
	 * during the DEVICE_CREATE, DEVICE_CONFIGURED, and
	 * DEVICE_SET_INTERFACE events.	 We need to reconfigure the OMAP packet
	 * RAM after bi_config scans the selected device configuration and
	 * initializes the endpoint structures, but before this routine enables
	 * the OUT endpoint FIFOs.  Since bi_config calls this routine in a
	 * loop for endpoints 1 through UDC_MAX_ENDPOINTS, we reconfigure our
	 * packet RAM here when ep==1.
	 * I really hate to do this here, but it seems like the API exported
	 * by the USB bus interface controller driver to the usbd-bi module
	 * isn't quite right so there is no good place to do this.
	 */
	if (ep == 1) {
		omap1510_deconfigure_device ();
		omap1510_configure_device (device);
	}

	if (endpoint && (ep < UDC_MAX_ENDPOINTS)) {
		int ep_addr = endpoint->endpoint_address;

		if (!ep_addr) {
			/* nothing to do for endpoint 0 */
		} else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) {
			/* nothing to do for IN (tx) endpoints */
		} else {	/* OUT (rx) endpoint */
			if (endpoint->rcv_packetSize) {
				/*struct urb* urb = &(urb_out_array[ep&0xFF]); */
				/*urb->endpoint = endpoint; */
				/*urb->device = device; */
				/*urb->buffer_length = sizeof(urb->buffer); */

				/*endpoint->rcv_urb = urb; */
				omap1510_prepare_endpoint_for_rx (ep_addr);
			}
		}
	}
}

/**
 * udc_disable_ep - disable endpoint
 * @ep:
 *
 * Disable specified endpoint
 */
#if 0
void udc_disable_ep (unsigned int ep_addr)
{
	/*int ep_addr = PHYS_EP_TO_EP_ADDR(ep); */
	int ep_num = ep_addr & USB_ENDPOINT_NUMBER_MASK;
	struct usb_endpoint_instance *endpoint = omap1510_find_ep (ep_addr);	/*udc_device->bus->endpoint_array + ep; */

	UDCDBGA ("disable ep_addr %d", ep_addr);

	if (!ep_num) {
		/* nothing to do for endpoint 0 */ ;
	} else if ((ep_addr & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN) {
		if (endpoint->tx_packetSize) {
			/* we have a valid tx endpoint */
			/*usbd_flush_tx(endpoint); */
			endpoint->tx_urb = NULL;
		}
	} else {
		if (endpoint->rcv_packetSize) {
			/* we have a valid rx endpoint */
			/*usbd_flush_rcv(endpoint); */
			endpoint->rcv_urb = NULL;
		}
	}
}
#endif

/* ************************************************************************** */

/**
 * udc_connected - is the USB cable connected
 *
 * Return non-zero if cable is connected.
 */
#if 0
int udc_connected (void)
{
	return ((inw (UDC_DEVSTAT) & UDC_ATT) == UDC_ATT);
}
#endif

/* Turn on the USB connection by enabling the pullup resistor */
void udc_connect (void)
{
	UDCDBG ("connect, enable Pullup");
	outl (0x00000018, FUNC_MUX_CTRL_D);
}

/* Turn off the USB connection by disabling the pullup resistor */
void udc_disconnect (void)
{
	UDCDBG ("disconnect, disable Pullup");
	outl (0x00000000, FUNC_MUX_CTRL_D);
}

/* ************************************************************************** */


/*
 * udc_disable_interrupts - disable interrupts
 * switch off interrupts
 */
#if 0
void udc_disable_interrupts (struct usb_device_instance *device)
{
	UDCDBG ("disabling all interrupts");
	outw (0, UDC_IRQ_EN);
}
#endif

/* ************************************************************************** */

/**
 * udc_ep0_packetsize - return ep0 packetsize
 */
#if 0
int udc_ep0_packetsize (void)
{
	return EP0_PACKETSIZE;
}
#endif

/* Switch on the UDC */
void udc_enable (struct usb_device_instance *device)
{
	UDCDBGA ("enable device %p, status %d", device, device->status);

	/* initialize driver state variables */
	udc_devstat = 0;

	/* Save the device structure pointer */
	udc_device = device;

	/* Setup ep0 urb */
	if (!ep0_urb) {
		ep0_urb =
			usbd_alloc_urb (udc_device,
					udc_device->bus->endpoint_array);
	} else {
		serial_printf ("udc_enable: ep0_urb already allocated %p\n",
			       ep0_urb);
	}

	UDCDBG ("Check clock status");
	UDCREG (STATUS_REQ);

	/* The VBUS_MODE bit selects whether VBUS detection is done via
	 * software (1) or hardware (0).  When software detection is
	 * selected, VBUS_CTRL selects whether USB is not connected (0)
	 * or connected (1).
	 */
	outl (inl (FUNC_MUX_CTRL_0) | UDC_VBUS_CTRL | UDC_VBUS_MODE,
	      FUNC_MUX_CTRL_0);
	UDCREGL (FUNC_MUX_CTRL_0);

	omap1510_configure_device (device);
}

/* Switch off the UDC */
void udc_disable (void)
{
	UDCDBG ("disable UDC");

	omap1510_deconfigure_device ();

	/* The VBUS_MODE bit selects whether VBUS detection is done via
	 * software (1) or hardware (0).  When software detection is
	 * selected, VBUS_CTRL selects whether USB is not connected (0)
	 * or connected (1).
	 */
	outl (inl (FUNC_MUX_CTRL_0) | UDC_VBUS_MODE, FUNC_MUX_CTRL_0);
	outl (inl (FUNC_MUX_CTRL_0) & ~UDC_VBUS_CTRL, FUNC_MUX_CTRL_0);
	UDCREGL (FUNC_MUX_CTRL_0);

	/* Free ep0 URB */
	if (ep0_urb) {
		/*usbd_dealloc_urb(ep0_urb); */
		ep0_urb = NULL;
	}

	/* Reset device pointer.
	 * We ought to do this here to balance the initialization of udc_device
	 * in udc_enable, but some of our other exported functions get called
	 * by the bus interface driver after udc_disable, so we have to hang on
	 * to the device pointer to avoid a null pointer dereference. */
	/* udc_device = NULL; */
}

/**
 * udc_startup - allow udc code to do any additional startup
 */
void udc_startup_events (struct usb_device_instance *device)
{
	/* The DEVICE_INIT event puts the USB device in the state STATE_INIT. */
	usbd_device_event_irq (device, DEVICE_INIT, 0);

	/* The DEVICE_CREATE event puts the USB device in the state
	 * STATE_ATTACHED.
	 */
	usbd_device_event_irq (device, DEVICE_CREATE, 0);

	/* Some USB controller driver implementations signal
	 * DEVICE_HUB_CONFIGURED and DEVICE_RESET events here.
	 * DEVICE_HUB_CONFIGURED causes a transition to the state STATE_POWERED,
	 * and DEVICE_RESET causes a transition to the state STATE_DEFAULT.
	 * The OMAP USB client controller has the capability to detect when the
	 * USB cable is connected to a powered USB bus via the ATT bit in the
	 * DEVSTAT register, so we will defer the DEVICE_HUB_CONFIGURED and
	 * DEVICE_RESET events until later.
	 */

	udc_enable (device);
}

#endif