From d1a4aafd71991a3ddff97f7b6ec91b0952e2f4b6 Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Wed, 6 Aug 2014 12:59:52 +0900 Subject: powerpc: mpc8xx: remove svm_sc8xx board This board has been orphaned for a while and old enough. Signed-off-by: Masahiro Yamada --- include/commproc.h | 51 --------------------------------------------------- 1 file changed, 51 deletions(-) (limited to 'include/commproc.h') diff --git a/include/commproc.h b/include/commproc.h index 52ac4caf5a..fec818d13a 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -779,57 +779,6 @@ typedef struct scc_enet { /*** NETVIA *******************************************************/ -/* SinoVee Microsystems SC8xx series FEL8xx-AT,SC823,SC850,SC855T,SC860T */ -#if ( defined CONFIG_SVM_SC8xx ) -# ifndef CONFIG_FEC_ENET - -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 - - /* Bits in parallel I/O port registers that have to be set/cleared - * * * * to configure the pins for SCC2 use. - * * * */ -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0400) /* PA 5 */ -#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */ - -#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ - -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ -/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to - * * * * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. - * * * */ -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00003700) - -# else /* Use FEC for Fast Ethernet */ - -#undef SCC_ENET -#define FEC_ENET - -#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ -#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ -#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ -#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ -#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ -#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ -#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ -#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ -#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ -#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ -#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ -#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ -#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ - -#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */ - -# endif /* CONFIG_FEC_ENET */ -#endif /* CONFIG_SVM_SC8xx */ - - #if defined(CONFIG_NETVIA) /* Bits in parallel I/O port registers that have to be set/cleared * to configure the pins for SCC2 use. -- cgit v1.2.3