| Age | Commit message (Collapse) | Author |
|---|
|
While the DT parsing code recognizes "ok" as a valid value for the
"status" property, ePAPR v1.1 doesn't mention it in the list of valid
values.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Enable HS-USB device for the Henninger board, defining the GPIO that the driver
should check when probing (which is the ID output from MAX3355 OTG chip).
Note that there will be pinctrl-related error messages if both internal PCI
and HS-USB drivers are enabled but they should be just ignored.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: added pin function/group and prop, moved device node, fixed summary,
added changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Enable USB PHY device for the Henninger board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.
Note that we have to keep the "console=ttySC0,38400" parameter in
chosen/bootargs, else the console will use the default setting of 115200
baud.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the Henninger board dependent part of the VIN0 device node. Add the
device node for Analog Devices ADV7180 video decoder to I2C2 bus. Add the
necessary subnodes to interconnect VIN0 and ADV7180 devices.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Unify white space usage by consistently using tabs for indentation.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to
them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[horms+renesas@verge.net.au: minor witespace changes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the Henninger board dependent part of the I2C2 device node.
Based on the Koelsch I2C2 device tree patch by Wolfram Sang.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the Henninger board dependent part of the MSIOF0 device node.
Add device node for Renesas R2A11302FT PMIC for which no bindings exist yet.
Based on the Koelsch MSIOF device tree patch by Geert Uytterhoeven.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the Henninger board dependent part of the QSPI device node.
Add device nodes for Spansion S25FL512S SPI flash and MTD partitions on it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the Henninger board dependent part of the SDHI0/2 device nodes along with
the necessary voltage regulators (note that the Vcc regulators are dummy -- they
are required but don't actually exist on the board). Also, GPIOs have to be used
for the CD and WP signals due to the SDHI driver constraints...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
When creating the initial device tree for the Henninger board, I've overlooked
that EXTAL frequency needs to be overridden there. The 'sh-sci' driver managed
to work somehow but the SDHI driver that I've tried to enable just hanged with
the default EXTAL frequency of 0...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Enable SATA0 device for the Henninger board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Define the Henninger board dependent part of the Ether device node.
Enable DHCP and NFS root for the kernel booting.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add the initial device tree for the R8A7791 SoC based Henninger board. SCIF0
serial port support is included, so that the serial console can work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
