| Age | Commit message (Collapse) | Author |
|---|
|
As Mainlining effort for SolidRun CuBox has been carried out on the
Engineering Sample, the board DTS was reflecting this. Actually,
SolidRun CuBox comes in three different variants:
Engineering Sample (ES), production with 1GB RAM (1G),
and production with 2GB RAM (2G).
Therefore, we base current dove-cubox.dts on to the 1G production
variant and add a ES dts to add required quirk for misrouted SDHCI
card detect on top of dove-cubox.dts. For the 2G variant we rely on
the bootloader to setup correct RAM size.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1401228006-3212-1-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Generally, power LEDs should indicate when power is applied, and go out
once power is removed. _Not_ annoy the developer with migraine-inducing
blinking reminicent of some badly animated television series designed to
sell sugar to children.
On a more serious note, most of these OS-specific properties aren't
necessary and should be removed. I left two that are legitimately tying
disk LEDs to disk activity. Other than that, we keep the state the
bootloader left them in until userspace changes the state via sysfs.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
As defined in the DT, clkout2 is not allowed to change the pll inside
si5351.
This patch extends the properties of clkout2 so that it works as the
external clock of the audio device in the Cubox.
Also, as the second si5351 clock is not used in the Cubox, its
definition is removed.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This patch activates the audio device of the Cubox.
The audio flow (pin mpp_audio1) is output on both I2S and S/PDIF.
The third si5351 clock (#2, pin mpp13) is used as the external clock.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This coverts Dove DT board files to preprocessor includes instead
of dtc includes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This adds a node for the IR receiver connected to a GPIO pin on the
SolidRun CuBox.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This adds common dedicated and gpio pinmux functions to SoC pinctrl
node. It also relocates pinctrl references to corresponding DT nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This patch adds orion-eth and mvmdio device tree nodes for DT enabled
Dove boards. As there is only one ethernet controller on Dove, a default
phy node is also added with a note to set its reg property on a per-board
basis.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This patch adds the device tree node for si5351 clock generator
and the corresponding oscillator connected to it. It also limits
i2c frequency to 100kHz as there are bus locks reported on higher
frequencies.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
CuBox needs to enable USB power on a gpio pin. Add a fixed regulator
to always enable usb power on boot.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
gpio-leds has support for pinctrl allocation, make use of it.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Card detect for sdhci on Cubox is connected to the wrong pin
(sdio1_cd instead of sdio0_cd). With support for cd-gpios and
pinctrl add the corresponding properties to DT for Cubox.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
SolidRun CuBox has a led on a gpio pin. As there is now DT pinctrl
support for Dove, make use of a pinhog to ensure the pin is set to
gpio.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This patch adds basic support for the SolidRun CuBox to DT based
mach-dove. There are still some issues related to ongoing orion/mvebu
development, e.g. gpio-led will not work as there is no DT pinctrl
for dove yet and we don't have board specific setup code. Nevertheless,
the DT description is already introduced here.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
