summaryrefslogtreecommitdiff
path: root/arch/arm
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm')
-rw-r--r--arch/arm/boot/dts/ste-hrefv60plus.dtsi31
-rw-r--r--arch/arm/mach-ux500/board-mop500-pins.c16
2 files changed, 31 insertions, 16 deletions
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
index 6e0105d2f461..ecd26848f24f 100644
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -62,6 +62,10 @@
};
pinctrl {
+ /* Set this up using hogs */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ipgpio_hrefv60_mode>;
+
sdi0 {
/* SD card detect GPIO pin, extend default state */
sdi0_default_mode: sdi0_default {
@@ -71,6 +75,33 @@
};
};
};
+ ipgpio {
+ /*
+ * XENON Flashgun on image processor GPIO (controlled from image
+ * processor firmware), mux in these image processor GPIO lines 0
+ * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
+ * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
+ * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
+ */
+ ipgpio_hrefv60_mode: ipgpio_hrefv60 {
+ hrefv60_mux {
+ ste,function = "ipgpio";
+ ste,pins = "ipgpio0_c_1", "ipgpio1_c_1", "ipgpio4_c_1";
+ };
+ hrefv60_cfg1 {
+ ste,pins = "GPIO6_AF6", "GPIO7_AG5";
+ ste,config = <&in_pu>;
+ };
+ hrefv60_cfg2 {
+ ste,pins = "GPIO21_AB3";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg3 {
+ ste,pins = "GPIO64_F3";
+ ste,config = <&out_lo>;
+ };
+ };
+ };
};
};
};
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index d0d527a3d205..e208dddfeda9 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -20,8 +20,6 @@
#define BIAS(a,b) static unsigned long a[] = { b }
BIAS(pd, PIN_PULL_DOWN);
-BIAS(in_pu, PIN_INPUT_PULLUP);
-BIAS(out_lo, PIN_OUTPUT_LOW);
BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0));
BIAS(abx500_in_pd, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 1));
@@ -307,20 +305,6 @@ static struct pinctrl_map __initdata ab8505_pinmap[] = {
* and SSP1 ports (previously connected to the AB8500) as generic GPIO lines.
*/
static struct pinctrl_map __initdata hrefv60_pinmap[] = {
- /*
- * XENON Flashgun on image processor GPIO (controlled from image
- * processor firmware), mux in these image processor GPIO lines 0
- * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
- * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
- * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
- */
- DB8500_MUX_HOG("ipgpio0_c_1", "ipgpio"),
- DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"),
- DB8500_MUX_HOG("ipgpio4_c_1", "ipgpio"),
- DB8500_PIN_HOG("GPIO6_AF6", in_pu), /* XENON_FLASH_ID */
- DB8500_PIN_HOG("GPIO7_AG5", in_pu), /* XENON_READY */
- DB8500_PIN_HOG("GPIO21_AB3", gpio_out_lo), /* XENON_EN1 */
- DB8500_PIN_HOG("GPIO64_F3", out_lo), /* XENON_EN2 */
/* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
DB8500_PIN_HOG("GPIO31_V3", gpio_in_pu), /* EN1 */
DB8500_PIN_HOG("GPIO32_V2", gpio_in_pd), /* DRDY */