/* * Copyright (c) 2013-2014, ARM Limited and Contributors. All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions are met: * * Redistributions of source code must retain the above copyright notice, this * list of conditions and the following disclaimer. * * Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * * Neither the name of ARM nor the names of its contributors may be used * to endorse or promote products derived from this software without specific * prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ #include #include .globl bl1_entrypoint /* ----------------------------------------------------- * bl1_entrypoint() is the entry point into the trusted * firmware code when a cpu is released from warm or * cold reset. * ----------------------------------------------------- */ func bl1_entrypoint /* --------------------------------------------- * Set the CPU endianness before doing anything * that might involve memory reads or writes. * --------------------------------------------- */ mrs x0, sctlr_el3 bic x0, x0, #SCTLR_EE_BIT msr sctlr_el3, x0 isb /* --------------------------------------------- * Perform any processor specific actions upon * reset e.g. cache, tlb invalidations etc. * --------------------------------------------- */ bl reset_handler /* --------------------------------------------- * Enable the instruction cache, stack pointer * and data access alignment checks * --------------------------------------------- */ mov x1, #(SCTLR_I_BIT | SCTLR_A_BIT | SCTLR_SA_BIT) mrs x0, sctlr_el3 orr x0, x0, x1 msr sctlr_el3, x0 isb /* --------------------------------------------- * Set the exception vector to something sane. * --------------------------------------------- */ adr x0, bl1_exceptions msr vbar_el3, x0 isb /* --------------------------------------------- * Enable the SError interrupt now that the * exception vectors have been setup. * --------------------------------------------- */ msr daifclr, #DAIF_ABT_BIT /* --------------------------------------------------------------------- * The initial state of the Architectural feature trap register * (CPTR_EL3) is unknown and it must be set to a known state. All * feature traps are disabled. Some bits in this register are marked as * Reserved and should not be modified. * * CPTR_EL3.TCPAC: This causes a direct access to the CPACR_EL1 from EL1 * or the CPTR_EL2 from EL2 to trap to EL3 unless it is trapped at EL2. * CPTR_EL3.TTA: This causes access to the Trace functionality to trap * to EL3 when executed from EL0, EL1, EL2, or EL3. If system register * access to trace functionality is not supported, this bit is RES0. * CPTR_EL3.TFP: This causes instructions that access the registers * associated with Floating Point and Advanced SIMD execution to trap * to EL3 when executed from any exception level, unless trapped to EL1 * or EL2. * --------------------------------------------------------------------- */ mrs x0, cptr_el3 bic w0, w0, #TCPAC_BIT bic w0, w0, #TTA_BIT bic w0, w0, #TFP_BIT msr cptr_el3, x0 /* ------------------------------------------------------- * Will not return from this macro if it is a warm boot. * ------------------------------------------------------- */ wait_for_entrypoint bl platform_mem_init /* --------------------------------------------- * Init C runtime environment. * - Zero-initialise the NOBITS sections. * There are 2 of them: * - the .bss section; * - the coherent memory section. * - Copy the data section from BL1 image * (stored in ROM) to the correct location * in RAM. * --------------------------------------------- */ ldr x0, =__BSS_START__ ldr x1, =__BSS_SIZE__ bl zeromem16 ldr x0, =__COHERENT_RAM_START__ ldr x1, =__COHERENT_RAM_UNALIGNED_SIZE__ bl zeromem16 ldr x0, =__DATA_RAM_START__ ldr x1, =__DATA_ROM_START__ ldr x2, =__DATA_SIZE__ bl memcpy16 /* -------------------------------------------- * Allocate a stack whose memory will be marked * as Normal-IS-WBWA when the MMU is enabled. * There is no risk of reading stale stack * memory after enabling the MMU as only the * primary cpu is running at the moment. * -------------------------------------------- */ mrs x0, mpidr_el1 bl platform_set_stack /* --------------------------------------------- * Architectural init. can be generic e.g. * enabling stack alignment and platform spec- * ific e.g. MMU & page table setup as per the * platform memory map. Perform the latter here * and the former in bl1_main. * --------------------------------------------- */ bl bl1_early_platform_setup bl bl1_plat_arch_setup /* -------------------------------------------------- * Initialize platform and jump to our c-entry point * for this type of reset. Panic if it returns * -------------------------------------------------- */ bl bl1_main panic: b panic