| Age | Commit message (Collapse) | Author |
|---|
|
Uses common code for determining if an error should be retried on
alternate path.
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Uses common code for determining if an error should be retried on
alternate path.
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This removes nvme multipath's specific status decoding to see if failover
is needed, using the generic blk_status_t that was decoded earlier. This
abstraction from the raw NVMe status means all status decoding exists
in one place.
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This adds more NVMe status code translations to blk_status_t values,
and captures all the current status codes NVMe multipath uses.
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Use the fault injection framework to provide a way for null_blk
to configure timeouts. This only works for queue_mode 1 and 2,
since the bio mode doesn't have code for tracking timeouts.
Let's say you want to have a 10% chance of timing out every
100,000 requests, and for 5 total timeouts, you could do:
modprobe null_blk timeout="100000,10,0,5"
This is useful for adding blktests to test that IO timeouts
are handled appropriately.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This is needed to ensure that we actually handle timeouts.
Without it, the queue_mode=1 path will never call blk_add_timer(),
and the queue_mode=2 path will continually just return
EH_RESET_TIMER and we never actually complete the offending request.
This was used to test the new timeout code, and the changes around
killing off REQ_ATOM_COMPLETE.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Otherwise, architectures that do negated adds of atomics (e.g. s390)
to do atomic_sub fail in closure_set_stopped.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Bcache needs to scale the dirty data in the cache over the multiple
backing disks in order to calculate writeback rates for each.
The previous code did this by multiplying the target number of dirty
sectors by the backing device size, and expected it to fit into a
uint64_t; this blows up on relatively small backing devices.
The new approach figures out the bdev's share in 16384ths of the overall
cached data. This is chosen to cope well when bdevs drastically vary in
size and to ensure that bcache can cross the petabyte boundary for each
backing device.
This has been improved based on Tang Junhui's feedback to ensure that
every device gets a share of dirty data, no matter how small it is
compared to the total backing pool.
The existing mechanism is very limited; this is purely a bug fix to
remove limits on volume size. However, there still needs to be change
to make this "fair" over many volumes where some are idle.
Reported-by: Jack Douglas <jack@douglastechnology.co.uk>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Tang Junhui <tang.junhui@zte.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Bcache only does recoverable I/O for read operations by calling
cached_dev_read_error(). For write opertions there is no I/O recovery for
failed requests.
But in bch_count_io_errors() no matter read or write I/Os, before errors
counter reaches io error limit, pr_err() always prints "IO error on %,
recoverying". For write requests this information is misleading, because
there is no I/O recovery at all.
This patch adds a parameter 'is_read' to bch_count_io_errors(), and only
prints "recovering" by pr_err() when the bio direction is READ.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Tang Junhui <tang.junhui@zte.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Member devices of struct cache_set is used to reference all attached
bcache devices to this cache set. If it is treated as array of pointers,
size of devices[] is indicated by member nr_uuids of struct cache_set.
nr_uuids is calculated in drivers/md/super.c:bch_cache_set_alloc(),
bucket_bytes(c) / sizeof(struct uuid_entry)
Bucket size is determined by user space tool "make-bcache", by default it
is 1024 sectors (defined in bcache-tools/make-bcache.c:main()). So default
nr_uuids value is 4096 from the above calculation.
Every time when bcache code iterates bcache devices of a cache set, all
the 4096 pointers are checked even only 1 bcache device is attached to the
cache set, that's a wast of time and unncessary.
This patch adds a member devices_max_used to struct cache_set. Its value
is 1 + the maximum used index of devices[] in a cache set. When iterating
all valid bcache devices of a cache set, use c->devices_max_used in
for-loop may reduce a lot of useless checking.
Personally, my motivation of this patch is not for performance, I use it
in bcache debugging, which helps me to narrow down the scape to check
valid bcached devices of a cache set.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Tang Junhui <tang.junhui@zte.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The function cached_dev_make_request() and flash_dev_make_request() call
generic_start_io_acct() with (struct bcache_device)->disk when they start a
closure. Then the function bio_complete() calls generic_end_io_acct() with
(struct search)->orig_bio->bi_disk when the closure has done.
Since the `bi_disk` is not the bcache device, the generic_end_io_acct() is
called with a wrong device queue.
It causes the "inflight" (in struct hd_struct) counter keep increasing
without decreasing.
This patch fix the problem by calling generic_end_io_acct() with
(struct bcache_device)->disk.
Signed-off-by: Zhai Zhaoxuan <kxuanobj@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Reviewed-by: Tang Junhui <tang.junhui@zte.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
[edit by mlyle: include sched/debug.h to get __sched]
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Eliminates cases where sync can race and fail to complete / get stuck.
Removes many status flags and simplifies entering-and-exiting closure
sleeping behaviors.
[mlyle: fixed conflicts due to changed return behavior in mainline.
extended commit comment, and squashed down two commits that were mostly
contradictory to get to this state. Changed __set_current_state to
set_current_state per Jens review comment]
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If the control system would wait for at least half a second, and there's
been no reqs hitting the backing disk for awhile: use an alternate mode
where we have at most one contiguous set of writebacks in flight at a
time. (But don't otherwise delay). If front-end IO appears, it will
still be quick, as it will only have to contend with one real operation
in flight. But otherwise, we'll be sending data to the backing disk as
quickly as it can accept it (with one op at a time).
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Tang Junhui <tang.junhui@zte.com.cn>
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Writeback keys are presently iterated and dispatched for writeback in
order of the logical block address on the backing device. Multiple may
be, in parallel, read from the cache device and then written back
(especially when there are contiguous I/O).
However-- there was no guarantee with the existing code that the writes
would be issued in LBA order, as the reads from the cache device are
often re-ordered. In turn, when writing back quickly, the backing disk
often has to seek backwards-- this slows writeback and increases
utilization.
This patch introduces an ordering mechanism that guarantees that the
original order of issue is maintained for the write portion of the I/O.
Performance for writeback is significantly improved when there are
multiple contiguous keys or high writeback rates.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Tang Junhui <tang.junhui@zte.com.cn>
Tested-by: Tang Junhui <tang.junhui@zte.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
in bch_debug_init(), ret is always 0, and the return value is useless,
change it to return 0 if be success after calling debugfs_create_dir(),
else return a non-zero value.
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In such scenario that there are some flash only volumes
, and some cached devices, when many tasks request these devices in
writeback mode, the write IOs may fall to the same bucket as bellow:
| cached data | flash data | cached data | cached data| flash data|
then after writeback of these cached devices, the bucket would
be like bellow bucket:
| free | flash data | free | free | flash data |
So, there are many free space in this bucket, but since data of flash
only volumes still exists, so this bucket cannot be reclaimable,
which would cause waste of bucket space.
In this patch, we segregate flash only volume write streams from
cached devices, so data from flash only volumes and cached devices
can store in different buckets.
Compare to v1 patch, this patch do not add a additionally open bucket
list, and it is try best to segregate flash only volume write streams
from cached devices, sectors of flash only volumes may still be mixed
with dirty sectors of cached device, but the number is very small.
[mlyle: fixed commit log formatting, permissions, line endings]
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Fix ptr_ret.cocci warnings:
drivers/md/bcache/btree.c:1800:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently, when a cached device detaching from cache, writeback thread is
not stopped, and writeback_rate_update work is not canceled. For example,
after the following command:
echo 1 >/sys/block/sdb/bcache/detach
you can still see the writeback thread. Then you attach the device to the
cache again, bcache will create another writeback thread, for example,
after below command:
echo ba0fb5cd-658a-4533-9806-6ce166d883b9 > /sys/block/sdb/bcache/attach
then you will see 2 writeback threads.
This patch stops writeback thread and cancels writeback_rate_update work
when cached device detaching from cache.
Compare with patch v1, this v2 patch moves code down into the register
lock for safety in case of any future changes as Coly and Mike suggested.
[edit by mlyle: commit log spelling/formatting]
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The read request might meet error when searching the btree, but the error
was not handled in cache_lookup(), and this kind of metadata failure will
not go into cached_dev_read_error(), finally, the upper layer will receive
bi_status=0. In this patch we judge the metadata error by the return
value of bch_btree_map_keys(), there are two potential paths give rise to
the error:
1. Because the btree is not totally cached in memery, we maybe get error
when read btree node from cache device (see bch_btree_node_get()), the
likely errno is -EIO, -ENOMEM
2. When read miss happens, bch_btree_insert_check_key() will be called to
insert a "replace_key" to btree(see cached_dev_cache_miss(), just for
doing preparatory work before insert the missed data to cache device),
a failure can also happen in this situation, the likely errno is
-ENOMEM
bch_btree_map_keys() will return MAP_DONE in normal scenario, but we will
get either -EIO or -ENOMEM in above two cases. if this happened, we should
NOT recover data from backing device (when cache device is dirty) because
we don't know whether bkeys the read request covered are all clean. And
after that happened, s->iop.status is still its initially value(0) before
we submit s->bio.bio, we set it to BLK_STS_IOERR, so it can go into
cached_dev_read_error(), and finally it can be passed to upper layer, or
recovered by reread from backing device.
[edit by mlyle: patch formatting, word-wrap, comment spelling,
commit log format]
Signed-off-by: Hua Rui <huarui.dev@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There is a problem when another module (e.g. nvmet) takes a reference on
the nvme block device and the physical nvme drive is removed. In that
case nvme_free_ctrl() will not be called and the controller state will be
"deleting" or "dead" unless nvmet module releases the block device.
Later on, the same nvme drive probes back and nvme_init_subsystem() will
be called and fail due to duplicate subnqn (if the nvme device doesn't
support subsystem with multiple controllers). This will cause a probe
failure. This commit changes the check of multiple controllers support
at nvme_init_subsystem() by not counting all the controllers at "dead" or
"deleting" state (this is safe because controllers at this state will
never be active again).
Fixes: ab9e00cc72fa ("nvme: track subsystems")
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The block device is backed by the transport so we must ensure that the
transport driver will not be removed until all references are released.
Otherwise, we might end up referencing freed memory.
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Nitzan Carmi <nitzanc@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
When the io queues setup or tagset allocation failed, ctrl.tagset is
NULL. But the scan work will still be queued and executed, then panic
comes up due to NULL pointer reference of ctrl.tagset.
To fix this, add a new ctrl state NVME_CTRL_ADMIN_ONLY to inidcate only
admin queue is live. When non io queues or tagset allocation failed, ctrl
enters into this state, scan work will not be started. But async event
work and nvme dev ioctl will be still available. This will be helpful to
do further investigation and recovery.
Suggested-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
When an NVMe controller reports RTD3 Entry Latency larger than the value
of shutdown_timeout module parameter, we update the shutdown_timeout
accordingly to honor RTD3 Entry Latency. Use an informational debug level
instead of a warning level for it.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Make it symmetric to nvmet_alloc_ctrl().
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Remove the allocated id on error.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The local variable __size__ will be set a bit later in a for-loop.
Remove the explicit initialization at the beginning of this function.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
NVMe transport driver module unload may (and usually does) trigger
iteration over the active controllers and delete them all (sometimes
under a mutex). However, a controller can be created concurrently with
module unload which can lead to leakage of resources (most important char
device node leakage) in case the controller creation occured after the
unload delete and drain sequence. To protect against this, we take a
module reference to guarantee that the nvme transport driver is not
unloaded while creating a controller.
Signed-off-by: Roy Shterman <roys@lightbitslabs.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The current fc transport add_port routine validates that there is a
matching port to the target port config. It then takes a reference
on the targetport. The del_port removes the reference.
Unfortunately, if the LLDD undergoes a hw reset or driver unload and
wants to unreg the targetport, due to the reference, the targetport
effectively can't be removed. It requires the admin to remove the
port from the nvmet config first, which calls the del_port.
Note: it appears nvmetcli clear skips over the del_port call (I'm
not attempting to change that).
There's no real reason to take the reference. With FC, there is nothing
to enable or disable as the presence of the FC targetport implicitly
means its enabled, and removal of the targtport means its disabled.
Change add_port to simply validate and change remove_port to a noop.
No references are taken on the targetport.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The split between what the host accesses on its flows vs what the
target side accesses was flawed. Abort handling didn't properly
clear initiator vs target structure cross-reference and locks
weren't used for synchronization. Thus, there were issues of
freeing structures too soon and access after free.
A couple of these existed pre the IN_ISR mods, but when the
target upcalls were converted to work items, thus adding delays
between the 2 sides of accesses, the problems became pronounced.
Resolve by:
- tracking io state mainly in the tgt-side io structure.
- make the tgt-side io structure released by reference not by
code flow.
- when changing initiator structures, use locks for
synchronization
- aborts are clearly tracked for which side saw the abort, and
after seeing the abort, cross-references are cleared under lock.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The existing fcloop driver expects the target side upcalls to
the transport to context switch, thus the calls into the nvmet layer
are not done in the calling context of the host/initiator down calls.
The xxx_IN_ISR feature flags are used to select this logic.
The xxx_IN_ISR feature flags should go away in the nvmet_fc transport
as no other lldd utilizes them. Both Broadcom and Cavium lldds have their
own non-ISR deferred handlers thus the nvmet calls can be made directly.
This patch converts the paths that make the target upcalls (command
receive, abort receive) such that they schedule a work item rather
than expecting the transport to schedule the work item.
The patch also cleans up the following:
- The completion path from target to host scheduled a host work
element called "work". Rename it "tio_done_work" for code clarity.
- The abort io path called a iniwork item to call the host side
io done. This is no longer needed as the abort routine can make
the same call.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The current fcloop driver gets its lport structure from the private
area co-allocated with the fc_localport. All is fine except the
teardown path, which wants to wait on the completion, which is marked
complete by the delete_localport callback performed after
unregister_localport. The issue is, the nvme_fc transport frees the
localport structure immediately after delete_localport is called,
meaning the original routine is trying to wait on a complete that
was just freed.
Change such that a lport struct is allocated coincident with the
addition and registration of a localport. The private area of the
localport now contains just a backpointer to the real lport struct.
Now, the completion can be waited for, and after completing, the
new structure can be kfree'd.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
A test case revealed a race condition of an i/o completing on a thread
parallel to the delete_association generating the aborts for the
outstanding ios on the controller. The i/o completion was freeing the
target fcloop context, thus the abort task referenced the just-freed
memory.
Correct by clearing the target/initiator cross pointers in the io
completion and abort tasks before calling the callbacks. On aborts
that detect already finished io's, ensure the complete context is
called.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
It is a bit chatty to report on each queue, log it only for debug
purposes.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
It is a bit chatty to report on every deleted queue, so keep it for debug
purposes only.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
We already do that when we are notified in device removal
which is triggered when unregistering as an ib client.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Use the sgl_alloc_order() and sgl_free() functions instead of open
coding these functions.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Use the sgl_alloc() and sgl_free() functions instead of open coding
these functions.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Use the sgl_alloc() and sgl_free() functions instead of open coding
these functions.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When CONFIG_KASAN is set, all the local variables in this function are
allocated on the stack together, leading to a warning about possible
kernel stack overflow:
drivers/block/DAC960.c: In function 'DAC960_gam_ioctl':
drivers/block/DAC960.c:7061:1: error: the frame size of 2240 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
By splitting up the function into smaller chunks, we can avoid that and
make the code slightly more readable at the same time. The coding style
in this file is completely nonstandard, and I chose to not touch that
at all, leaving the unconventional intendation unchanged to make it
easier to review the diff.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The bio is always freed after running crypt_free_buffer_pages(), so it
isn't necessary to clear bv->bv_page.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc:dm-devel@redhat.com
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
bcache is the only user of bio_alloc_pages(), so move this function into
bcache, and avoid it being misused in the future.
Also rename it to bch_bio_allo_pages() since it is bcache only.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
All direct access to bvec table are safe even after multipage bvec is
supported.
Cc: linux-bcache@vger.kernel.org
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
For BIO based DM, some targets aren't ready for dealing with bigger
incoming bio than 1Mbyte, such as crypt target.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc:dm-devel@redhat.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch converts to bio_first_bvec_all() & bio_first_page_all() for
retrieving the 1st bvec/page, and prepares for supporting multipage bvec.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Call bdev_get_queue(bdev) after bdev->bd_disk has been initialized
instead of just before that pointer has been initialized. This patch
avoids that the following command
pktsetup 1 /dev/sr0
triggers the following kernel crash:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000548
IP: pkt_setup_dev+0x2db/0x670 [pktcdvd]
CPU: 2 PID: 724 Comm: pktsetup Not tainted 4.15.0-rc4-dbg+ #1
Call Trace:
pkt_ctl_ioctl+0xce/0x1c0 [pktcdvd]
do_vfs_ioctl+0x8e/0x670
SyS_ioctl+0x3c/0x70
entry_SYSCALL_64_fastpath+0x23/0x9a
Reported-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Fixes: commit ca18d6f769d2 ("block: Make most scsi_req_init() calls implicit")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Cc: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 523e1d399ce0 ("block: make gendisk hold a reference to its queue")
modified add_disk() and disk_release() but did not update any of the
error paths that trigger a put_disk() call after disk->queue has been
assigned. That introduced the following behavior in the pktcdvd driver
if pkt_new_dev() fails:
Kernel BUG at 00000000e98fd882 [verbose debug info unavailable]
Since disk_release() calls blk_put_queue() anyway if disk->queue != NULL,
fix this by removing the blk_cleanup_queue() call from the pkt_setup_dev()
error path.
Fixes: commit 523e1d399ce0 ("block: make gendisk hold a reference to its queue")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Cc: <stable@vger.kernel.org> # v3.2
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Shorten function to simply return the value of the if statement.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Since pblk registers its own block device, the iostat accounting is
not automatically done for us. Therefore, add the necessary
accounting logic to satisfy the iostat interface.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
