/* * (C) Copyright 2001 * * SPDX-License-Identifier: GPL-2.0+ */ /* * board/config.h - configuration options, board specific */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options * (easy to change) */ #define CONFIG_405GP 1 /* This is a PPC405 CPU */ #define CONFIG_4xx 1 /* ...member of PPC4xx family */ #define CONFIG_SBC405 1 /* ...on a WR SBC405 board */ #define CONFIG_SYS_TEXT_BASE 0xFFFC0000 #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ #define CONFIG_BAUDRATE 9600 #define CONFIG_PREBOOT "echo;echo Welcome to U-Boot for the sbc405;echo;echo Type \"? or help\" to get on-line help;echo" #define CONFIG_RAMBOOT \ "setenv bootargs root=/dev/ram rw nfsroot=${serverip}:${rootpath} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ "bootm ffc00000 ffca0000" #define CONFIG_NFSBOOT \ "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ "bootm ffc00000" #undef CONFIG_BOOTARGS #define CONFIG_BOOTCOMMAND "version;echo;tftpboot ${loadaddr} ${loadfile};bootvx" /* autoboot command */ #define CONFIG_PPC4xx_EMAC #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_PHY_RESET_DELAY 300 /* Intel LXT971A needs this */ #define CONFIG_EXTRA_ENV_SETTINGS \ "bootargs=emac(0,0)host:/T221ppc/target/config/sbc405/vxWorks.st " \ "e=192.168.193.102:ffffffe0 h=192.168.193.100 u=target pw=hello " \ "f=0x08 tn=sbc405 o=emac \0" \ "env_startaddr=FF000000\0" \ "env_endaddr=FF03FFFF\0" \ "loadfile=vxWorks.st\0" \ "loadaddr=0x01000000\0" \ "net_load=tftpboot ${loadaddr} ${loadfile}\0" \ "uboot_startaddr=FFFC0000\0" \ "uboot_endaddr=FFFFFFFF\0" \ "update=tftp ${loadaddr} u-boot.bin;" \ "protect off ${uboot_startaddr} ${uboot_endaddr};" \ "era ${uboot_startaddr} ${uboot_endaddr};" \ "cp.b ${loadaddr} ${uboot_startaddr} ${filesize};" \ "protect on ${uboot_startaddr} ${uboot_endaddr}\0" \ "zapenv=protect off ${env_startaddr} ${env_endaddr};" \ "era ${env_startaddr} ${env_endaddr};" \ "protect on ${env_startaddr} ${env_endaddr}\0" #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ /* * BOOTP options */ #define CONFIG_BOOTP_SUBNETMASK #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_ENV_OVERWRITE /* * Command line configuration. */ #include #define CONFIG_CMD_BSP #define CONFIG_CMD_ELF #define CONFIG_CMD_I2C #define CONFIG_CMD_IRQ #define CONFIG_CMD_MII #define CONFIG_CMD_PCI #define CONFIG_CMD_PING #define CONFIG_CMD_SDRAM #undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ #define CONFIG_ETHADDR DE:AD:BE:EF:01:01 /* Ethernet address */ #define CONFIG_IPADDR 192.168.193.102 #define CONFIG_NETMASK 255.255.255.224 #define CONFIG_SERVERIP 192.168.193.119 #define CONFIG_GATEWAYIP 192.168.193.97 /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CONFIG_CONS_INDEX 1 /* Use UART0 */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_serial_clock() #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ #define CONFIG_SYS_BASE_BAUD 691200 /* The following table includes the supported baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE \ { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ 57600, 115200, 230400, 460800, 921600 } #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_info (bd_t) */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ #define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ #define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ #define PCI_HOST_FORCE 1 /* configure as pci host */ #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ #define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ /* resource configuration */ #define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0408 /* PCI Device ID: PMC-405 */ #define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ #define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ #define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ #define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ #define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ #define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_MONITOR_BASE 0xFFFC0000 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ #define CONFIG_SYS_FLASH_BASE 0xFF000000 #define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Flash Erase Timeout (in ms) */ #define CONFIG_SYS_FLASH_INCREMENT 0x01000000 #undef CONFIG_SYS_FLASH_PROTECTION /* don't use hardware protection */ #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ /*----------------------------------------------------------------------- * Environment Variable setup */ #define CONFIG_ENV_ADDR CONFIG_SYS_FLASH_BASE /* starting right at the beginning */ #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_OFFSET 0 /* starting right at the beginning */ #define CONFIG_ENV_SECT_SIZE 0x40000 /* see README - env sector total size */ #define CONFIG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup */ #define FLASH0_BA CONFIG_SYS_FLASH_BASE /* FLASH 0 Base Address */ /* Memory Bank 0 (Flash Bank 0) initialization */ #define CONFIG_SYS_EBC_PB0AP 0x92015480 #define CONFIG_SYS_EBC_PB0CR FLASH0_BA | 0x9C000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=32bit*/ /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in data cache) */ /* use on chip memory ( OCM ) for temperary stack until sdram is tested */ #define CONFIG_SYS_TEMP_STACK_OCM 1 /* On Chip Memory location */ #define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ #define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Definitions for Serial Presence Detect EEPROM address * (to get SDRAM settings) */ #define SPD_EEPROM_ADDRESS 0x50 #define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ #endif /* __CONFIG_H */