/* * (C) Copyright 2004-2008 Texas Instruments, * Rohit Choraria * * See file CREDITS for list of people who contributed to this * project. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ #include #include #include #include #include #include #include #include #include #include #ifdef CONFIG_AM33XX #include #endif static uint8_t cs; static __maybe_unused struct nand_ecclayout hw_nand_oob = GPMC_NAND_HW_ECC_LAYOUT; static __maybe_unused struct nand_ecclayout hw_bch8_nand_oob = GPMC_NAND_HW_BCH8_ECC_LAYOUT; /* * omap_nand_hwcontrol - Set the address pointers corretly for the * following address/data/command operation */ static void omap_nand_hwcontrol(struct mtd_info *mtd, int32_t cmd, uint32_t ctrl) { register struct nand_chip *this = mtd->priv; /* * Point the IO_ADDR to DATA and ADDRESS registers instead * of chip address */ switch (ctrl) { case NAND_CTRL_CHANGE | NAND_CTRL_CLE: this->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_cmd; break; case NAND_CTRL_CHANGE | NAND_CTRL_ALE: this->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_adr; break; case NAND_CTRL_CHANGE | NAND_NCE: this->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_dat; break; } if (cmd != NAND_CMD_NONE) writeb(cmd, this->IO_ADDR_W); } #ifdef CONFIG_SPL_BUILD /* Check wait pin as dev ready indicator */ int omap_spl_dev_ready(struct mtd_info *mtd) { return gpmc_cfg->status & (1 << 8); } #endif /* * omap_hwecc_init - Initialize the Hardware ECC for NAND flash in * GPMC controller * @mtd: MTD device structure * */ static void __maybe_unused omap_hwecc_init(struct nand_chip *chip) { /* * Init ECC Control Register * Clear all ECC | Enable Reg1 */ writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control); writel(ECCSIZE1 | ECCSIZE0 | ECCSIZE0SEL, &gpmc_cfg->ecc_size_config); } /* * gen_true_ecc - This function will generate true ECC value, which * can be used when correcting data read from NAND flash memory core * * @ecc_buf: buffer to store ecc code * * @return: re-formatted ECC value */ static uint32_t gen_true_ecc(uint8_t *ecc_buf) { return ecc_buf[0] | (ecc_buf[1] << 16) | ((ecc_buf[2] & 0xF0) << 20) | ((ecc_buf[2] & 0x0F) << 8); } /* * omap_correct_data - Compares the ecc read from nand spare area with ECC * registers values and corrects one bit error if it has occured * Further details can be had from OMAP TRM and the following selected links: * http://en.wikipedia.org/wiki/Hamming_code * http://www.cs.utexas.edu/users/plaxton/c/337/05f/slides/ErrorCorrection-4.pdf * * @mtd: MTD device structure * @dat: page data * @read_ecc: ecc read from nand flash * @calc_ecc: ecc read from ECC registers * * @return 0 if data is OK or corrected, else returns -1 */ static int __maybe_unused omap_correct_data(struct mtd_info *mtd, uint8_t *dat, uint8_t *read_ecc, uint8_t *calc_ecc) { uint32_t orig_ecc, new_ecc, res, hm; uint16_t parity_bits, byte; uint8_t bit; /* Regenerate the orginal ECC */ orig_ecc = gen_true_ecc(read_ecc); new_ecc = gen_true_ecc(calc_ecc); /* Get the XOR of real ecc */ res = orig_ecc ^ new_ecc; if (res) { /* Get the hamming width */ hm = hweight32(res); /* Single bit errors can be corrected! */ if (hm == 12) { /* Correctable data! */ parity_bits = res >> 16; bit = (parity_bits & 0x7); byte = (parity_bits >> 3) & 0x1FF; /* Flip the bit to correct */ dat[byte] ^= (0x1 << bit); } else if (hm == 1) { printf("Error: Ecc is wrong\n"); /* ECC itself is corrupted */ return 2; } else { /* * hm distance != parity pairs OR one, could mean 2 bit * error OR potentially be on a blank page.. * orig_ecc: contains spare area data from nand flash. * new_ecc: generated ecc while reading data area. * Note: if the ecc = 0, all data bits from which it was * generated are 0xFF. * The 3 byte(24 bits) ecc is generated per 512byte * chunk of a page. If orig_ecc(from spare area) * is 0xFF && new_ecc(computed now from data area)=0x0, * this means that data area is 0xFF and spare area is * 0xFF. A sure sign of a erased page! */ if ((orig_ecc == 0x0FFF0FFF) && (new_ecc == 0x00000000)) return 0; printf("Error: Bad compare! failed\n"); /* detected 2 bit error */ return -1; } } return 0; } /* * omap_calculate_ecc - Generate non-inverted ECC bytes. * * Using noninverted ECC can be considered ugly since writing a blank * page ie. padding will clear the ECC bytes. This is no problem as * long nobody is trying to write data on the seemingly unused page. * Reading an erased page will produce an ECC mismatch between * generated and read ECC bytes that has to be dealt with separately. * E.g. if page is 0xFF (fresh erased), and if HW ECC engine within GPMC * is used, the result of read will be 0x0 while the ECC offsets of the * spare area will be 0xFF which will result in an ECC mismatch. * @mtd: MTD structure * @dat: unused * @ecc_code: ecc_code buffer */ static int __maybe_unused omap_calculate_ecc(struct mtd_info *mtd, const uint8_t *dat, uint8_t *ecc_code) { u_int32_t val; /* Start Reading from HW ECC1_Result = 0x200 */ val = readl(&gpmc_cfg->ecc1_result); ecc_code[0] = val & 0xFF; ecc_code[1] = (val >> 16) & 0xFF; ecc_code[2] = ((val >> 8) & 0x0F) | ((val >> 20) & 0xF0); /* * Stop reading anymore ECC vals and clear old results * enable will be called if more reads are required */ writel(0x000, &gpmc_cfg->ecc_config); return 0; } /* * omap_enable_ecc - This function enables the hardware ecc functionality * @mtd: MTD device structure * @mode: Read/Write mode */ static void __maybe_unused omap_enable_hwecc(struct mtd_info *mtd, int32_t mode) { struct nand_chip *chip = mtd->priv; uint32_t val, dev_width = (chip->options & NAND_BUSWIDTH_16) >> 1; switch (mode) { case NAND_ECC_READ: case NAND_ECC_WRITE: /* Clear the ecc result registers, select ecc reg as 1 */ writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control); /* * Size 0 = 0xFF, Size1 is 0xFF - both are 512 bytes * tell all regs to generate size0 sized regs * we just have a single ECC engine for all CS */ writel(ECCSIZE1 | ECCSIZE0 | ECCSIZE0SEL, &gpmc_cfg->ecc_size_config); val = (dev_width << 7) | (cs << 1) | (0x1); writel(val, &gpmc_cfg->ecc_config); break; default: printf("Error: Unrecognized Mode[%d]!\n", mode); break; } } /* * Generic BCH interface */ struct nand_bch_priv { uint8_t mode; uint8_t type; uint8_t nibbles; struct bch_control *control; }; /* bch types */ #define ECC_BCH4 0 #define ECC_BCH8 1 #define ECC_BCH16 2 /* GPMC ecc engine settings */ #define BCH_WRAPMODE_1 1 /* BCH wrap mode 1 */ #define BCH_WRAPMODE_6 6 /* BCH wrap mode 6 */ /* BCH nibbles for diff bch levels */ #define NAND_ECC_HW_BCH ((uint8_t)(NAND_ECC_HW_OOB_FIRST) + 1) #define ECC_BCH4_NIBBLES 13 #define ECC_BCH8_NIBBLES 26 #define ECC_BCH16_NIBBLES 52 /* * This can be a single instance cause all current users have only one NAND * with nearly the same setup (BCH8, some with ELM and others with sw BCH * library). * When some users with other BCH strength will exists this have to change! */ static __maybe_unused struct nand_bch_priv bch_priv = { .mode = NAND_ECC_HW_BCH, .type = ECC_BCH8, .nibbles = ECC_BCH8_NIBBLES, .control = NULL }; /* * omap_hwecc_init_bch - Initialize the BCH Hardware ECC for NAND flash in * GPMC controller * @mtd: MTD device structure * @mode: Read/Write mode */ __maybe_unused static void omap_hwecc_init_bch(struct nand_chip *chip, int32_t mode) { uint32_t val; uint32_t dev_width = (chip->options & NAND_BUSWIDTH_16) >> 1; #ifdef CONFIG_AM33XX uint32_t unused_length = 0; #endif uint32_t wr_mode = BCH_WRAPMODE_6; struct nand_bch_priv *bch = chip->priv; /* Clear the ecc result registers, select ecc reg as 1 */ writel(ECCCLEAR | ECCRESULTREG1, &gpmc_cfg->ecc_control); #ifdef CONFIG_AM33XX wr_mode = BCH_WRAPMODE_1; switch (bch->nibbles) { case ECC_BCH4_NIBBLES: unused_length = 3; break; case ECC_BCH8_NIBBLES: unused_length = 2; break; case ECC_BCH16_NIBBLES: unused_length = 0; break; } /* * This is ecc_size_config for ELM mode. * Here we are using different settings for read and write access and * also depending on BCH strength. */ switch (mode) { case NAND_ECC_WRITE: /* write access only setup eccsize1 config */ val = ((unused_length + bch->nibbles) << 22); break; case NAND_ECC_READ: default: /* * by default eccsize0 selected for ecc1resultsize * eccsize0 config. */ val = (bch->nibbles << 12); /* eccsize1 config */ val |= (unused_length << 22); break; } #else /* * This ecc_size_config setting is for BCH sw library. * * Note: we only support BCH8 currently with BCH sw library! * Should be really easy to adobt to BCH4, however some omap3 have * flaws with BCH4. * * Here we are using wrapping mode 6 both for reading and writing, with: * size0 = 0 (no additional protected byte in spare area) * size1 = 32 (skip 32 nibbles = 16 bytes per sector in spare area) */ val = (32 << 22) | (0 << 12); #endif /* ecc size configuration */ writel(val, &gpmc_cfg->ecc_size_config); /* * Configure the ecc engine in gpmc * We assume 512 Byte sector pages for access to NAND. */ val = (1 << 16); /* enable BCH mode */ val |= (bch->type << 12); /* setup BCH type */ val |= (wr_mode << 8); /* setup wrapping mode */ val |= (dev_width << 7); /* setup device width (16 or 8 bit) */ val |= (cs << 1); /* setup chip select to work on */ debug("set ECC_CONFIG=0x%08x\n", val); writel(val, &gpmc_cfg->ecc_config); } /* * omap_enable_ecc_bch - This function enables the bch h/w ecc functionality * @mtd: MTD device structure * @mode: Read/Write mode */ __maybe_unused static void omap_enable_ecc_bch(struct mtd_info *mtd, int32_t mode) { struct nand_chip *chip = mtd->priv; omap_hwecc_init_bch(chip, mode); /* enable ecc */ writel((readl(&gpmc_cfg->ecc_config) | 0x1), &gpmc_cfg->ecc_config); } /* * omap_ecc_disable - Disable H/W ECC calculation * * @mtd: MTD device structure */ static void __maybe_unused omap_ecc_disable(struct mtd_info *mtd) { writel((readl(&gpmc_cfg->ecc_config) & ~0x1), &gpmc_cfg->ecc_config); } /* * BCH8 support (needs ELM and thus AM33xx-only) */ #ifdef CONFIG_AM33XX /* * omap_read_bch8_result - Read BCH result for BCH8 level * * @mtd: MTD device structure * @big_endian: When set read register 3 first * @ecc_code: Read syndrome from BCH result registers */ static void omap_read_bch8_result(struct mtd_info *mtd, uint8_t big_endian, uint8_t *ecc_code) { uint32_t *ptr; int8_t i = 0, j; if (big_endian) { ptr = &gpmc_cfg->bch_result_0_3[0].bch_result_x[3]; ecc_code[i++] = readl(ptr) & 0xFF; ptr--; for (j = 0; j < 3; j++) { ecc_code[i++] = (readl(ptr) >> 24) & 0xFF; ecc_code[i++] = (readl(ptr) >> 16) & 0xFF; ecc_code[i++] = (readl(ptr) >> 8) & 0xFF; ecc_code[i++] = readl(ptr) & 0xFF; ptr--; } } else { ptr = &gpmc_cfg->bch_result_0_3[0].bch_result_x[0]; for (j = 0; j < 3; j++) { ecc_code[i++] = readl(ptr) & 0xFF; ecc_code[i++] = (readl(ptr) >> 8) & 0xFF; ecc_code[i++] = (readl(ptr) >> 16) & 0xFF; ecc_code[i++] = (readl(ptr) >> 24) & 0xFF; ptr++; } ecc_code[i++] = readl(ptr) & 0xFF; ecc_code[i++] = 0; /* 14th byte is always zero */ } } /* * omap_rotate_ecc_bch - Rotate the syndrome bytes * * @mtd: MTD device structure * @calc_ecc: ECC read from ECC registers * @syndrome: Rotated syndrome will be retuned in this array * */ static void omap_rotate_ecc_bch(struct mtd_info *mtd, uint8_t *calc_ecc, uint8_t *syndrome) { struct nand_chip *chip = mtd->priv; struct nand_bch_priv *bch = chip->priv; uint8_t n_bytes = 0; int8_t i, j; switch (bch->type) { case ECC_BCH4: n_bytes = 8; break; case ECC_BCH16: n_bytes = 28; break; case ECC_BCH8: default: n_bytes = 13; break; } for (i = 0, j = (n_bytes-1); i < n_bytes; i++, j--) syndrome[i] = calc_ecc[j]; } /* * omap_calculate_ecc_bch - Read BCH ECC result * * @mtd: MTD structure * @dat: unused * @ecc_code: ecc_code buffer */ static int omap_calculate_ecc_bch(struct mtd_info *mtd, const uint8_t *dat, uint8_t *ecc_code) { struct nand_chip *chip = mtd->priv; struct nand_bch_priv *bch = chip->priv; uint8_t big_endian = 1; int8_t ret = 0; if (bch->type == ECC_BCH8) omap_read_bch8_result(mtd, big_endian, ecc_code); else /* BCH4 and BCH16 currently not supported */ ret = -1; /* * Stop reading anymore ECC vals and clear old results * enable will be called if more reads are required */ omap_ecc_disable(mtd); return ret; } /* * omap_fix_errors_bch - Correct bch error in the data * * @mtd: MTD device structure * @data: Data read from flash * @error_count:Number of errors in data * @error_loc: Locations of errors in the data * */ static void omap_fix_errors_bch(struct mtd_info *mtd, uint8_t *data, uint32_t error_count, uint32_t *error_loc) { struct nand_chip *chip = mtd->priv; struct nand_bch_priv *bch = chip->priv; uint8_t count = 0; uint32_t error_byte_pos; uint32_t error_bit_mask; uint32_t last_bit = (bch->nibbles * 4) - 1; /* Flip all bits as specified by the error location array. */ /* FOR( each found error location flip the bit ) */ for (count = 0; count < error_count; count++) { if (error_loc[count] > last_bit) { /* Remove the ECC spare bits from correction. */ error_loc[count] -= (last_bit + 1); /* Offset bit in data region */ error_byte_pos = ((512 * 8) - (error_loc[count]) - 1) / 8; /* Error Bit mask */ error_bit_mask = 0x1 << (error_loc[count] % 8); /* Toggle the error bit to make the correction. */ data[error_byte_pos] ^= error_bit_mask; } } } /* * omap_correct_data_bch - Compares the ecc read from nand spare area * with ECC registers values and corrects one bit error if it has occured * * @mtd: MTD device structure * @dat: page data * @read_ecc: ecc read from nand flash (ignored) * @calc_ecc: ecc read from ECC registers * * @return 0 if data is OK or corrected, else returns -1 */ static int omap_correct_data_bch(struct mtd_info *mtd, uint8_t *dat, uint8_t *read_ecc, uint8_t *calc_ecc) { struct nand_chip *chip = mtd->priv; struct nand_bch_priv *bch = chip->priv; uint8_t syndrome[28]; uint32_t error_count = 0; uint32_t error_loc[8]; uint32_t i, ecc_flag; ecc_flag = 0; for (i = 0; i < chip->ecc.bytes; i++) if (read_ecc[i] != 0xff) ecc_flag = 1; if (!ecc_flag) return 0; elm_reset(); elm_config((enum bch_level)(bch->type)); /* * while reading ECC result we read it in big endian. * Hence while loading to ELM we have rotate to get the right endian. */ omap_rotate_ecc_bch(mtd, calc_ecc, syndrome); /* use elm module to check for errors */ if (elm_check_error(syndrome, bch->nibbles, &error_count, error_loc) != 0) { printf("ECC: uncorrectable.\n"); return -1; } /* correct bch error */ if (error_count > 0) omap_fix_errors_bch(mtd, dat, error_count, error_loc); return 0; } /** * omap_read_page_bch - hardware ecc based page read function * @mtd: mtd info structure * @chip: nand chip info structure * @buf: buffer to store read data * @oob_required: caller expects OOB data read to chip->oob_poi * @page: page number to read * */ static int omap_read_page_bch(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *buf, int oob_required, int page) { int i, eccsize = chip->ecc.size; int eccbytes = chip->ecc.bytes; int eccsteps = chip->ecc.steps; uint8_t *p = buf; uint8_t *ecc_calc = chip->buffers->ecccalc; uint8_t *ecc_code = chip->buffers->ecccode; uint32_t *eccpos = chip->ecc.layout->eccpos; uint8_t *oob = chip->oob_poi; uint32_t data_pos; uint32_t oob_pos; data_pos = 0; /* oob area start */ oob_pos = (eccsize * eccsteps) + chip->ecc.layout->eccpos[0]; oob += chip->ecc.layout->eccpos[0]; for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize, oob += eccbytes) { chip->ecc.hwctl(mtd, NAND_ECC_READ); /* read data */ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, data_pos, page); chip->read_buf(mtd, p, eccsize); /* read respective ecc from oob area */ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, oob_pos, page); chip->read_buf(mtd, oob, eccbytes); /* read syndrome */ chip->ecc.calculate(mtd, p, &ecc_calc[i]); data_pos += eccsize; oob_pos += eccbytes; } for (i = 0; i < chip->ecc.total; i++) ecc_code[i] = chip->oob_poi[eccpos[i]]; eccsteps = chip->ecc.steps; p = buf; for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { int stat; stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]); if (stat < 0) mtd->ecc_stats.failed++; else mtd->ecc_stats.corrected += stat; } return 0; } #endif /* CONFIG_AM33XX */ /* * OMAP3 BCH8 support (with BCH library) */ #ifdef CONFIG_NAND_OMAP_BCH8 /* * omap_calculate_ecc_bch - Read BCH ECC result * * @mtd: MTD device structure * @dat: The pointer to data on which ecc is computed (unused here) * @ecc: The ECC output buffer */ static int omap_calculate_ecc_bch(struct mtd_info *mtd, const uint8_t *dat, uint8_t *ecc) { int ret = 0; size_t i; unsigned long nsectors, val1, val2, val3, val4; nsectors = ((readl(&gpmc_cfg->ecc_config) >> 4) & 0x7) + 1; for (i = 0; i < nsectors; i++) { /* Read hw-computed remainder */ val1 = readl(&gpmc_cfg->bch_result_0_3[i].bch_result_x[0]); val2 = readl(&gpmc_cfg->bch_result_0_3[i].bch_result_x[1]); val3 = readl(&gpmc_cfg->bch_result_0_3[i].bch_result_x[2]); val4 = readl(&gpmc_cfg->bch_result_0_3[i].bch_result_x[3]); /* * Add constant polynomial to remainder, in order to get an ecc * sequence of 0xFFs for a buffer filled with 0xFFs. */ *ecc++ = 0xef ^ (val4 & 0xFF); *ecc++ = 0x51 ^ ((val3 >> 24) & 0xFF); *ecc++ = 0x2e ^ ((val3 >> 16) & 0xFF); *ecc++ = 0x09 ^ ((val3 >> 8) & 0xFF); *ecc++ = 0xed ^ (val3 & 0xFF); *ecc++ = 0x93 ^ ((val2 >> 24) & 0xFF); *ecc++ = 0x9a ^ ((val2 >> 16) & 0xFF); *ecc++ = 0xc2 ^ ((val2 >> 8) & 0xFF); *ecc++ = 0x97 ^ (val2 & 0xFF); *ecc++ = 0x79 ^ ((val1 >> 24) & 0xFF); *ecc++ = 0xe5 ^ ((val1 >> 16) & 0xFF); *ecc++ = 0x24 ^ ((val1 >> 8) & 0xFF); *ecc++ = 0xb5 ^ (val1 & 0xFF); } /* * Stop reading anymore ECC vals and clear old results * enable will be called if more reads are required */ omap_ecc_disable(mtd); return ret; } /** * omap_correct_data_bch - Decode received data and correct errors * @mtd: MTD device structure * @data: page data * @read_ecc: ecc read from nand flash * @calc_ecc: ecc read from HW ECC registers */ static int omap_correct_data_bch(struct mtd_info *mtd, u_char *data, u_char *read_ecc, u_char *calc_ecc) { int i, count; /* cannot correct more than 8 errors */ unsigned int errloc[8]; struct nand_chip *chip = mtd->priv; struct nand_bch_priv *chip_priv = chip->priv; struct bch_control *bch = chip_priv->control; count = decode_bch(bch, NULL, 512, read_ecc, calc_ecc, NULL, errloc); if (count > 0) { /* correct errors */ for (i = 0; i < count; i++) { /* correct data only, not ecc bytes */ if (errloc[i] < 8*512) data[errloc[i]/8] ^= 1 << (errloc[i] & 7); printf("corrected bitflip %u\n", errloc[i]); #ifdef DEBUG puts("read_ecc: "); /* * BCH8 have 13 bytes of ECC; BCH4 needs adoption * here! */ for (i = 0; i < 13; i++) printf("%02x ", read_ecc[i]); puts("\n"); puts("calc_ecc: "); for (i = 0; i < 13; i++) printf("%02x ", calc_ecc[i]); puts("\n"); #endif } } else if (count < 0) { puts("ecc unrecoverable error\n"); } return count; } /** * omap_free_bch - Release BCH ecc resources * @mtd: MTD device structure */ static void __maybe_unused omap_free_bch(struct mtd_info *mtd) { struct nand_chip *chip = mtd->priv; struct nand_bch_priv *chip_priv = chip->priv; struct bch_control *bch = NULL; if (chip_priv) bch = chip_priv->control; if (bch) { free_bch(bch); chip_priv->control = NULL; } } #endif /* CONFIG_NAND_OMAP_BCH8 */ #ifndef CONFIG_SPL_BUILD /* * omap_nand_switch_ecc - switch the ECC operation between different engines * (h/w and s/w) and different algorithms (hamming and BCHx) * * @hardware - true if one of the HW engines should be used * @eccstrength - the number of bits that could be corrected * (1 - hamming, 4 - BCH4, 8 - BCH8, 16 - BCH16) */ void omap_nand_switch_ecc(uint32_t hardware, uint32_t eccstrength) { struct nand_chip *nand; struct mtd_info *mtd; if (nand_curr_device < 0 || nand_curr_device >= CONFIG_SYS_MAX_NAND_DEVICE || !nand_info[nand_curr_device].name) { printf("Error: Can't switch ecc, no devices available\n"); return; } mtd = &nand_info[nand_curr_device]; nand = mtd->priv; nand->options |= NAND_OWN_BUFFERS; /* Reset ecc interface */ nand->ecc.mode = NAND_ECC_NONE; nand->ecc.read_page = NULL; nand->ecc.write_page = NULL; nand->ecc.read_oob = NULL; nand->ecc.write_oob = NULL; nand->ecc.hwctl = NULL; nand->ecc.correct = NULL; nand->ecc.calculate = NULL; nand->ecc.strength = eccstrength; /* Setup the ecc configurations again */ if (hardware) { if (eccstrength == 1) { nand->ecc.mode = NAND_ECC_HW; nand->ecc.layout = &hw_nand_oob; nand->ecc.size = 512; nand->ecc.bytes = 3; nand->ecc.hwctl = omap_enable_hwecc; nand->ecc.correct = omap_correct_data; nand->ecc.calculate = omap_calculate_ecc; omap_hwecc_init(nand); printf("1-bit hamming HW ECC selected\n"); } #if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8) else if (eccstrength == 8) { nand->ecc.mode = NAND_ECC_HW; nand->ecc.layout = &hw_bch8_nand_oob; nand->ecc.size = 512; #ifdef CONFIG_AM33XX nand->ecc.bytes = 14; nand->ecc.read_page = omap_read_page_bch; #else nand->ecc.bytes = 13; #endif nand->ecc.hwctl = omap_enable_ecc_bch; nand->ecc.correct = omap_correct_data_bch; nand->ecc.calculate = omap_calculate_ecc_bch; omap_hwecc_init_bch(nand, NAND_ECC_READ); printf("8-bit BCH HW ECC selected\n"); } #endif } else { nand->ecc.mode = NAND_ECC_SOFT; /* Use mtd default settings */ nand->ecc.layout = NULL; nand->ecc.size = 0; printf("SW ECC selected\n"); } /* Update NAND handling after ECC mode switch */ nand_scan_tail(mtd); nand->options &= ~NAND_OWN_BUFFERS; } #endif /* CONFIG_SPL_BUILD */ /* * Board-specific NAND initialization. The following members of the * argument are board-specific: * - IO_ADDR_R: address to read the 8 I/O lines of the flash device * - IO_ADDR_W: address to write the 8 I/O lines of the flash device * - cmd_ctrl: hardwarespecific function for accesing control-lines * - waitfunc: hardwarespecific function for accesing device ready/busy line * - ecc.hwctl: function to enable (reset) hardware ecc generator * - ecc.mode: mode of ecc, see defines * - chip_delay: chip dependent delay for transfering data from array to * read regs (tR) * - options: various chip options. They can partly be set to inform * nand_scan about special functionality. See the defines for further * explanation */ int board_nand_init(struct nand_chip *nand) { int32_t gpmc_config = 0; cs = 0; /* * xloader/Uboot's gpmc configuration would have configured GPMC for * nand type of memory. The following logic scans and latches on to the * first CS with NAND type memory. * TBD: need to make this logic generic to handle multiple CS NAND * devices. */ while (cs < GPMC_MAX_CS) { /* Check if NAND type is set */ if ((readl(&gpmc_cfg->cs[cs].config1) & 0xC00) == 0x800) { /* Found it!! */ break; } cs++; } if (cs >= GPMC_MAX_CS) { printf("NAND: Unable to find NAND settings in " "GPMC Configuration - quitting\n"); return -ENODEV; } gpmc_config = readl(&gpmc_cfg->config); /* Disable Write protect */ gpmc_config |= 0x10; writel(gpmc_config, &gpmc_cfg->config); nand->IO_ADDR_R = (void __iomem *)&gpmc_cfg->cs[cs].nand_dat; nand->IO_ADDR_W = (void __iomem *)&gpmc_cfg->cs[cs].nand_cmd; nand->cmd_ctrl = omap_nand_hwcontrol; nand->options = NAND_NO_PADDING | NAND_CACHEPRG; /* If we are 16 bit dev, our gpmc config tells us that */ if ((readl(&gpmc_cfg->cs[cs].config1) & 0x3000) == 0x1000) nand->options |= NAND_BUSWIDTH_16; nand->chip_delay = 100; #if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8) #ifdef CONFIG_AM33XX /* AM33xx uses the ELM */ /* required in case of BCH */ elm_init(); #else /* * Whereas other OMAP based SoC do not have the ELM, they use the BCH * SW library. */ bch_priv.control = init_bch(13, 8, 0x201b /* hw polynominal */); if (!bch_priv.control) { puts("Could not init_bch()\n"); return -ENODEV; } #endif /* BCH info that will be correct for SPL or overridden otherwise. */ nand->priv = &bch_priv; #endif /* Default ECC mode */ #if defined(CONFIG_AM33XX) || defined(CONFIG_NAND_OMAP_BCH8) nand->ecc.mode = NAND_ECC_HW; nand->ecc.layout = &hw_bch8_nand_oob; nand->ecc.size = CONFIG_SYS_NAND_ECCSIZE; nand->ecc.bytes = CONFIG_SYS_NAND_ECCBYTES; nand->ecc.strength = 8; nand->ecc.hwctl = omap_enable_ecc_bch; nand->ecc.correct = omap_correct_data_bch; nand->ecc.calculate = omap_calculate_ecc_bch; #ifdef CONFIG_AM33XX nand->ecc.read_page = omap_read_page_bch; #endif omap_hwecc_init_bch(nand, NAND_ECC_READ); #else #if !defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_NAND_SOFTECC) nand->ecc.mode = NAND_ECC_SOFT; #else nand->ecc.mode = NAND_ECC_HW; nand->ecc.layout = &hw_nand_oob; nand->ecc.size = CONFIG_SYS_NAND_ECCSIZE; nand->ecc.bytes = CONFIG_SYS_NAND_ECCBYTES; nand->ecc.hwctl = omap_enable_hwecc; nand->ecc.correct = omap_correct_data; nand->ecc.calculate = omap_calculate_ecc; nand->ecc.strength = 1; omap_hwecc_init(nand); #endif #endif #ifdef CONFIG_SPL_BUILD if (nand->options & NAND_BUSWIDTH_16) nand->read_buf = nand_read_buf16; else nand->read_buf = nand_read_buf; nand->dev_ready = omap_spl_dev_ready; #endif return 0; }