From 490f204096d6e2c9940f67816f154a8125bab116 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 6 Jun 2008 15:55:03 +0200 Subject: ppc4xx: Unify AMCC's board config files (part 2/3) This patch series unifies the AMCC eval board ports by introducing a common include header for all AMCC eval boards: include/configs/amcc-common.h This header now includes all common configuration options/defines which are removed from the board specific headers. The reason for this is ease of maintenance and unified look and feel of all AMCC boards. Signed-off-by: Stefan Roese --- include/configs/bamboo.h | 168 +++++++---------------------------------------- 1 file changed, 22 insertions(+), 146 deletions(-) (limited to 'include/configs/bamboo.h') diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index 8d77164059..41058f88cf 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -36,6 +36,12 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME bamboo +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ /* @@ -49,10 +55,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */ #define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ #define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 @@ -84,14 +86,9 @@ * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * NVRAM/RTC * @@ -227,10 +224,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -244,54 +238,20 @@ #define CFG_ENV_OFFSET 0x0 #endif /* CFG_ENV_IS_IN_EEPROM */ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=bamboo\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/bamboo/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fff00000\0" \ "ramdisk_addr=fff10000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/bamboo/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b 100000 fffa0000 60000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_HAS_ETH0 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ #define CONFIG_PHY1_ADDR 1 @@ -299,16 +259,6 @@ #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #endif /* CONFIG_BAMBOO_NAND */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI 1 /* required for netconsole */ - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - #ifdef CONFIG_440EP /* USB */ #define CONFIG_USB_OHCI @@ -318,77 +268,27 @@ #define USB_2_0_DEVICE #endif /*CONFIG_440EP*/ - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM -#define CONFIG_CMD_USB -#define CONFIG_CMD_FAT -#define CONFIG_CMD_EXT2 #define CONFIG_CMD_SNTP +#define CONFIG_CMD_USB #ifdef CONFIG_BAMBOO_NAND #define CONFIG_CMD_NAND #endif - #define CONFIG_SUPPORT_VFAT -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CONFIG_LYNXKDI 1 /* support kdi files */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION /*----------------------------------------------------------------------- * PCI stuff @@ -407,28 +307,4 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ -- cgit v1.2.3