| Age | Commit message (Collapse) | Author |
|---|
|
The Hydra and Superhydra (P3041DS, P5020DS, and P5040DS) boards have a
second USB port that can be configured in either host, peripheral (aka
device), or OTG (on-the-go) mode. When configured in host mode, if
the port is connected to another USB host, damage to the board can
occur.
To avoid this, we change the default setting to peripheral mode. Ideally,
we'd set it to OTG mode, but currently there is no OTG support for
these boards.
Setting the hwconfig variable will also update the device tree, and so
Linux will configure the port for peripheral mode as well.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Add defines needed to access NAND, remove second flash bank that is
actually connected to NAND.
Add nand booting support for P1022DS with hardcoded DDR config using
SPL framework from 2011
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
|
|
The changes to a3m071/a4m2k in summary are:
- Enable CAN1 on I2C in GPS Port Configuration
- Enable SPI on PSC2
- Activate network console
- New flash partitioning
- Fix some typos
- Pass host name to Linux
- Change rootfs to squashfs,jffs2
- Enable UBI/UBIFS support
- Enable FIT support
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The v2013.04 release has this patch set included:
5cb48582 "Add architecture-specific global data"
With this, the global_data struct is now common and new variables
have been added. Resulting in a bigger struct. Unfortunately the
currently allocated 128 bytes are just a bit too small for this
new struct.
This patch now uses the automatically generated struct size instead to
not run into this problem again.
Please note that this problem might hit some other platforms which
currently reserve a tight space of 128 bytes for the global_data
struct!
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The prt_mpc512x_clks() function isn't referenced
anywhere and its prototype is wrong. Remove it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
|
|
The redundancy related defines are only correct for NAND, so guard all
of that area with CONFIG_ENV_IS_IN_NAND
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
|
|
In order to use the generic hang() later on pull libgeneric in SPL.
This has no impact on the SPL size.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
In order to use the generic hang() later on pull libgeneric in SPL.
This has no impact on the SPL size.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
log2 of the device block size serves as the shift value used to calculate
the block number to read in file systems when implementing avaiable block
sizes.
It is needed quite often in file systems thus it is pre-calculated and
stored in the block device descriptor.
Signed-off-by: Egbert Eich <eich@suse.com>
|
|
For ISO we check the block size of the device if this is != the CD sector
size we assume that the device has no ISO partition.
Signed-off-by: Egbert Eich <eich@suse.com>
|
|
Disks beyond 2T in size use blocksizes of 4096 bytes. However a lot of
code in u-boot still assumes a 512 byte blocksize.
This patch fixes the handling of GPTs.
Signed-off-by: Egbert Eich <eich@suse.com>
|
|
The number 512 appears quite a bit in the mmc code. Add a constant for this
so that it can be used here and in other parts of the code (e.g. SPL code
which loads from mmc).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
|
|
Align some comments.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
include/configs/m28evk.h
|
|
Change all "#define<TAB>" sequences into "#define<SPACE>"
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
|
|
When CONFIG_REGEX is enabled, the new option "-e" becomes available
which causes regular expression matches to be used. This allows for
example things like these:
- print all MAC addresses:
=> env grep -e eth.*addr
eth1addr=00:10:ec:80:c5:15
ethaddr=00:10:ec:00:c5:15
- print all variables that have at least 2 colons in their value:
=> env grep -v -e :.*:
addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off
panic=1
eth1addr=00:10:ec:80:c5:15
ethaddr=00:10:ec:00:c5:15
ver=U-Boot 2013.04-rc1-00289-g497746b-dirty (Mar 22 2013 - 12:50:25)
etc.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Downloaded from http://slre.sourceforge.net/
and adapted for U-Boot environment.
Used to implement regex operations on environment variables.
Code size is ~ 3.5 KiB on PPC.
To enable this code, define the CONFIG_REGEX option in your board
config file.
Note: There are more recent versions of the SLRE library available at
http://slre.googlecode.com ; unfortunately, the new code has a heavily
reorked API which makes it less usable for our purposes:
- the return code is strings, which are more difficult to process
- we don't get any information any more which sub-string of the data
was matched by the given regex
- it is much more cumbersome to work with arbitrary expressions, where
for example the number of substrings for capturing are not known at
compile time
Also, there does not seem to be any real changes or improvements of
the functionality.
Because of this, we deliberately stick with the older code.
Note 2: the test code (built when SLRE_TEST is defined) was modified
to allow for more extensive testing; now we can test the regexp
matching on all lines on a text file (instead of the whole data in the
file as a single block).
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Also drop hstrstr_r() which is not needed any more.
The new code is way more flexible.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
The output of "env grep" is unsorted, and printing is done by a
private implementation to parse the hash table. We have all the
needed code in place in hexport_r() alsready, so let's use this
instead. Here we prepare the code for this, without any functional
changes yet.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Enable these options to use FITs on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This allows write of files from the host filesystem in sandbox. There is
currently no concept of overwriting the file and removing its existing
contents - all writing is done on top of what is there. This means that
writing 10 bytes to the start of a 1KB file will only update those 10
bytes, not truncate the file to 10 byte slong.
If the file does not exist it is created.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add a new method for saving that filesystems can implement. This mirrors the
existing load method.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This conversion is required in a number of places in U-Boot. Add a
standard function to provide this feature, so we avoid all the different
variations in the way it is coded.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
With sandbox it is tricky to add an FDT to the image at build time (or
later) since we build an ELF file, not a plain binary, and the address
space of the whole U-Boot is not accessible in the emulated memory map
of sandbox.
Sandbox can read files directly from the host, though, so add an option
to read an FDT from a host file on start-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add generic board support for sandbox. and remove the old board init code.
Select CONFIG_SYS_GENERIC_BOARD for sandbox now that this is supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
In many cases, pointers to memory are passed around, and these pointers
refer to U-Boot memory, not host memory. This in itself is not a
problem.
However, in a few places, we cast that pointer back to a ulong (being
a U-Boot memory address). It is possible to convert many of these cases
to avoid this. However there are data structures (e.g. struct
bootm_headers) which use pointers. We could with a lot of effort adjust
the structs and all code that uses them to use ulong instead of pointers.
This seems like an unacceptable cost, since our objective with sandbox
is to minimise the impact on U-Boot code while maximising the features
available to sandbox.
Therefore, create a map_to_sysmem() function which converts from a
pointer to a U-Boot address. This can be used sparingly when needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
Support Xilinx Zynq i2c controller.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Add support for SD, MMC and eMMC card on Xilinx Zynq.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Avoid overwriting GEMx_RCLK_CTRL and GEMx_CLK_CTRL
if the Ethernet interface is connect on EMIO
Do not enable emio for this standard board configuration for now.
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Pass the PHY address to the driver init to
allow parallel use of both interfaces
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Add all fixed addresses to hardware.h and change petalinux
configuration to support this.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Move baseaddr to hardware.h to be shared between
configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Watchdog can be used on Microblaze, PPC and Zynq hw designs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Setup environment and enable netconsole.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
This allows to test the iim driver in the mainline tree.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
Make all mpc512x code point to the new common fsl_iim driver, and remove the
former mpc512x-specific iim driver.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
This can be useful for fuse-like hardware, OTP SoC options, etc.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
This reworks the environment settings to be aligned with the other
i.MX boards. The loadaddr has been changed to allow the Freescale
kernel and mainline kernel to work without environment changes.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
FSL 2.6.35 kernel expects that revision tag is passed by the bootloader.
Select CONFIG_REVISION_TAG so that mx53 boards can work properly with 2.6.35.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Currently mmcrootfstype is set to ext3 type.
It is better not to force it in the env vars, because users may prefer a
different file system type, so let's get rid of 'mmcrootfstype'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
Update the environment as done in other imx boards to allow easy switching
between booting a non-dt kernel and a dt kernel.
Change CONFIG_LOADADDR to 0x92000000, so that we can have the:
- uImage at 0x92000000
- imx51-babbage.dtb at 0x91000000
,which are adequate locations in RAM to avoid overlapping.
Boot tested the following kernels:
- 2.6.35 from FSL (11.09 branch)
- 3.9-rc7 non-dt
- 3.9-rc7 dt
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
Adds support for 'bmode' command which let user to choose where to
boot from; this allows U-Boot to load system from another storage
without messing with jumpers.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
|
|
Allow use of the carrier board MicroSD card available in the
Wandboard; this allow for loading alternative system from the other
card for testing or upgrade proposes.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
|
