summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2009-05-15Fix e-mail address of Gary Jennejohn.Detlev Zundel
Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-05-15powerpc/inka4x0: Remove left-over ide reset code.Detlev Zundel
The pin which was used in preliminary versions of the board for ide reset is really connected to the rtc clock. Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-05-15arm/imx31_phycore: Fix bi_arch_numberDetlev Zundel
Signed-off-by: Detlev Zundel <dzu@denx.de> Cc: Sascha Hauer <s.hauer@pengutronix.de>
2009-05-13AFEB9260 network fixSergey Lapin
AFEB9260 uses PA10, PA11 for ETX2 and ETX3. Also, due to extarnal pull-up on IRQ line, Micrel PHY ID is 1 after reset sequence, not 0. Signed-off-by: Sergey Lapin <slapin@ossfans.org>
2009-05-06Blackfin: bf518f-ezbrd: reset ethernet PHY during initGraf Yang
We don't know what state the ethernet PHY is in when starting up, so make sure we set it to a sane state. This fixes troubles seen when Linux boots up, configures the PHY is a non-default state, and then the system reboots into U-Boot which previously expected a reset state only. Signed-off-by: Graf Yang <graf.yang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-05-06Blackfin: fix booting with older bootroms (no EVT1)Mike Frysinger
When dropping jump block support, the assumption was that all bootroms supported entry point redirection via the EVT1 register. Unfortunately, this turned out to be incorrect for the oldest Blackfin parts (BF533-0.2 and older and BF561). No one really noticed earlier because these parts usually are booted by bypassing the bootrom entirely, and older BF533 parts are not supported at all (too many anomalies). Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-30OMAP3: Beagle: Set pinmux conditionally for Rev C boardsDirk Behme
The Beagle Rev C boards pull UART2 from an alternate set of balls. Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-04-30Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2009-04-29OMAP3: Remove unused board-typesSanjeev Premi
The board-types defined in struct omap3_sysinfo seem to be unused. The function display_board_info() is passed board type as an argument; which is ignored. This patch removes all uses of board-type, related definitions and functions. Signed-off-by: Sanjeev Premi <premi@ti.com>
2009-04-28ids8247: Remove legacy NAND definesHeiko Schocher
because legacy NAND support is deprecated converting to current NAND interface. !This just compile, because I have no more the hardware to test it. Signed-off-by: Heiko Schocher <hs@denx.de>
2009-04-28Replace __asm references with __asm__Peter Tyser
__asm__ follows gcc's documented syntax and is generally more common than __asm. This change is only asthetic and should not affect functionality. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-04-24Merge branch 'master' of git://git.denx.de/u-boot-at91Wolfgang Denk
2009-04-16at91: add support for the PM9263 board of Ronetix GmbHIlko Iliev
The PM9263 board is based on the AT91SAM9263-EK board. Here is the page on Ronetix website: http://www.ronetix.at/starter_kit_9263.html Signed-off-by: Ilko Iliev <iliev@ronetix.at> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-16at91sam9/at91cap: improve clock frameworkJean-Christophe PLAGNIOL-VILLARD
calculate dynamically the clock rate and pllb setting for usb Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-16ppc4xx: Remove unused code for Sequoia NAND booting versionStefan Roese
The current define of get_bus_freq() in the CONFIG_NAND_SPL #ifdef is not used at all. This patch changes it's define to the currently used value of 133333333 and removes the unnecessary code. Signed-off-by: Stefan Roese <sr@denx.de>
2009-04-16ppc4xx: Fixup chip-selects in dtb for NAND-booting SequoiaStefan Roese
Currently the NOR & NAND support in Linux only works for the "standard" Sequoia, the version booting for NOR flash. The NAND-booting version has the chip-selects swapped. Here the chip-select mappings: "Standard" NOR-booting version: CS0 NOR CS3 NAND NAND-booting version: CS0 NAND CS3 NOR With this path the dtb gets fixed-up, so that the correct chip-select numbers are patched in the dtb enabling correct NOR & NAND support in Linux on the NAND-booting Sequoia version. Signed-off-by: Stefan Roese <sr@denx.de>
2009-04-05Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2009-04-05OMAP3: Update Overo pin mux for new expansion boardDirk Behme
A new Overo expansion board uses GPIO 14, 21, 22 and 23 for LED's and switches. This patch changes the pinmux configuration for those pins. They were previously set up for unused MMC3_DAT4-7. Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-04-05arm: clean cache managementJean-Christophe PLAGNIOL-VILLARD
unify arm cache management except for non standard cache as ARM7TDMI Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-05Move machine specific code to board at s3c64xx (v2)Kyungmin Park
Move machine specific code to smdk6400. Some board use OneNAND instead of NAND. Some register MP0_CS_CFG[5:0] are controled by both h/w and s/w. So it's better to use macro instead of hard-coded value. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-04-05OMAP3 Fix multiline formatting in board init files.Tom Rix
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-04-05Update CHANGELOG, coding style cleanup.Wolfgang Denk
2009-04-04Small fix to m5282evbAlan Carvalho de Assis
This is just a small fix to get u-boot on m5282evb. Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
2009-04-04Merge branch 'master' of git://git.denx.de/u-boot-at91Wolfgang Denk
2009-04-04at91rm9200: Reset updateJean-Christophe PLAGNIOL-VILLARD
Update the rm9200 reset sequence to try executing a board-specific reset function and move specific board reset to board. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04Add support for the AT91RM9200EK Board.Ulf Samuelsson
The AT91RM9200-EK Evaluation Board supports the AT91RM9200 ARM9-based 32-bit RISC microcontroller and enables real-time code development and evaluation. Here is the chip page on Atmel website: http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507 with - NOR (cfi driver) - DataFlash - USB OHCI - Net - I2C (hard) Signed-off-by: Ulf Samuelsson <ulf@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04at91rm9200dk: Move conditional compilation to MakefileJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04at91: rename DATAFLASH_MMC_SELECT to CONFIG_DATAFLASH_MMC_SELECTJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04netstar: fix crc32.c dependancy locationJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
2009-04-04Fix quoting bug introduced by commit 74de7aefWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-04-04fsl_pci: Move prototypes into fsl_pci.h and remove explicit externsKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-04-04fsl_pci: Renamed immap_fsl_pci.h to fsl_pci.hKumar Gala
Rename the pci header for FSL HW so we can move some prototypes in there and stop doing explicit externs Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-04-03Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk
2009-04-03Rename common ns16550 constants with UART_ prefix to prevent conflictsDetlev Zundel
Fix problems introduced in commit 7b5611cdd12ca0cc33f994f0d4a4454788fc3124 [inka4x0: Add hardware diagnosis functions for inka4x0] which redefined MSR_RI which is already used on PowerPC systems. Also eliminate redundant definitions in ps2mult.h. More cleanup will be needed for other redundant occurrences though. Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-04-03Add "source" command; prepare removal of "autoscr" commandWolfgang Denk
According to the doc/feature-removal-schedule.txt, the "autoscr" command will be replaced by the "source" command in approximately 6 months from now. This patch prepares this change and starts a 6 month transition period as follows: - The new "source" command has been added, which implements exactly the same functionlaity as the old "autoscr" command before - The old "autoscr" command name is kept as an alias for compatibility - Command sequences, script files atc. have been adapted to use the new "source" command - Related environment variables ("autoscript", "autoscript_uname") have *not* been adapted yet; these will be renamed resp. removed in a separate patch when the support for the "autoscr" command get's finally dropped. Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-04-02Blackfin: bf533-stamp: drop old spi flash driverMike Frysinger
Now that the common SPI flash code supports all the flashes, we can stop using the old driver. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02Blackfin: bf537-stamp: split CF/IDE code out into dedicated cf-ide.cMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02Blackfin: bf518f-ezbrd: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02Blackfin: bf526-ezbrd: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02Blackfin: bf538f-ezkit: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02Blackfin: bf527-ezkit: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02Blackfin: bf548-ezkit: new board portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2009-04-0186xx: Cleanup MP supportKumar Gala
* Use CONFIG_MP instead of CONFIG_NUM_CPUS to match 85xx * Introduce determine_mp_bootpg() helper. We'll need this to address a bug introduced in v2009.03 with 86xx MP booting. We have to make sure to reserve the region of memory used for the MP bootpg() so other u-boot code doesn't use it. * Added dummy versions of cpu_reset(), cpu_status() & cpu_release() to allow cmd_mp.c to build and work. In the future we should look at implementing all these functions. This could be common w/85xx if we use spin tables on 86xx. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-03-31mpc8641hpcn/sbc8641d: Add missing board_lmb_reservesBecky Bruce
We're missing the board_lmb_reserve definitions that allow cpu_mp_lmb_reserve to be called; this means that Linux is free to reallocate reserved pages. Linux currently boots because we're getting lucky - the page we've reserved is high enough in memory that it isn't allocated by Linux while we still need it to be in existence. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-03-31NetStar: fix NANDLadislav Michl
Fix NAND support broken during new NAND code merge. Move those few lines of code to board/netstar/netstar.c Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2009-03-30MPC85xx: Add MPC8569MDS board supportHaiying Wang
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-03-3085xx: Use common LSDMR defines from asm/fsl_lbc.hKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-03-30inka4x0: Use proper accessor macros for memory mapped registers.Detlev Zundel
Signed-off-by: Detlev Zundel <dzu@denx.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-05-07 20:28:49 +0000