summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2008-01-09mpc85xx: Add support for ATUM8548 (updated)robert lazarski
Add support for Instituto Atlantico's ATUM8548 board Signed-off-by: robert lazarski <robertlazarski@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2008-01-09mpc85xx: Add support for ATUM8548 (updated)robert lazarski
Add support for Instituto Atlantico's ATUM8548 board Signed-off-by: robert lazarski <robertlazarski@gmail.com>
2008-01-09mpc85xx: Add support for SBC8548 (updated)Joe Hamman
Add support for Wind River's SBC8548 reference board. Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
2008-01-09mpc85xx: Add support for SBC8548 (updated)Joe Hamman
Add support for Wind River's SBC8548 reference board. Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com> Signed-off by: Andy Fleming <afleming@freescale.com>
2008-01-09MPC8568E-MDS: set up QE pario for UART1Anton Vorontsov
To use UART1 on the MPC8568E-MDS, QE pario pins PC[0:3] should be set up appropriately. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-01-09MPC8568E-MDS: reset UCCs to use them reliablyAnton Vorontsov
In order to use GETH1 and GETH2 on the MPC8568E-MDS, we should reset UCCs. p.s Similar code exists in the Linux kernel board file (for capability reasons with older U-Boots), but should be removed some day. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-01-09Reworked FSL Book-E TLB macros to be more readableKumar Gala
The old macros made it difficult to know what WIMGE and perm bits were set for a TLB entry. Actually use the bit masks for these items since they are only a single bit. Also moved the macros into mmu.h out of e500.h since they aren't specific to e500. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-09Merge branch 'master' of git://www.denx.de/git/u-boot-usbWolfgang Denk
2008-01-09fix comments with new drivers organizationMarcel Ziswiler
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2008-01-09Merge git://www.denx.de/git/u-bootMarkus Klotzbuecher
Conflicts: board/tqm5200/tqm5200.c
2008-01-09Improve configuration of FPGA subsystemMatthias Fuchs
This patch removes the FPGA subsystem configuration through the CONFIG_FPGA bitmask configuration option. See README for the new options: CONFIG_FPGA, CONFIG_FPGA_<vendor>, CONFIG_FPGA_<family> Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-01-09Coding Style cleanup, update CHANGELOGWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-09Merge branch 'master' of git://www.denx.de/git/u-boot-armWolfgang Denk
2008-01-09Merge branch 'master' of git://www.denx.de/git/u-boot-mpc83xxWolfgang Denk
2008-01-09Merge branch 'lwmon5-no-ocm'Stefan Roese
2008-01-09ppc4xx: Change LWMON5 to not use OCM for init-ram and POST anymoreStefan Roese
This patch configures the LWMON5 port to use d-cache as init-ram and the unused GPT0_COMP6 as POST WORD storage. Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-09ppc4xx: assign PCI interrupts on seuqoia boardsMatthias Fuchs
Some operating systems rely on assigned PCI interrupts. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-01-09ppc4xx: Update PLB/PCI divider for PMC440 boardMatthias Fuchs
This patch updates the PLB/PCI divider when running at 400MHz CPU frequency from 4 to 3 which results in 44MHz PCI sync clock. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-01-08Merge branch 'inka4x0-ng' of /home/m8/git/u-boot/Wolfgang Denk
2008-01-08mpc83xx: fix missed pci_hose -> hose conversion for new libfdt codeKim Phillips
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-08mpc83xx: rm remaining FLAT_TREE codeKim Phillips
..in board pci.c files Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-08mpc83xx: remove FLAT_TREE codeKim Phillips
need to rm it from pci code, too! Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-08mpc83xx: convert to using do_fixup_*()Kim Phillips
convert to using simpler mpc85xx style fdt update code; streamline by eliminating macros OF_SOC, OF_CPU, etc. which allows us to rm the old school FLAT_TREE code from 83xx (since the sbc8349 was just converted over to using libfdt). Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-08sbc8349: migrate board to libfdtPaul Gortmaker
This adds libfdt support code for the Wind River sbc8349 board. Parallel of commit 3fde9e8b22cfbd7af489214758f9839a206576cb for the other Freescale 83xx boards. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2008-01-08sbc8349: Remove board specific ECC codePaul Gortmaker
ECC code is now shared for all 83xx boards, so remove board specific one. See commit daab8c67d2defef73dc26ab07f0c3afd1b05d019 for reference. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2008-01-08mpc83xx: supress compiler warningKim Phillips
mpc8360emds.c: In function ‘ft_board_setup’: mpc8360emds.c:335: warning: assignment discards qualifiers from pointer target type mpc8360emds.c:345: warning: assignment discards qualifiers from pointer target type Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-08mpc83xx: fix remaining fdt_find_node_by_path referencesKim Phillips
rename to fdt_path_offset Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-08mpc83xx: mpc8360 rev.2.1 erratum 2: replace rgmii-id with rgmii-rxidKim Phillips
u-boot itself uses GMII mode on the 8360. Fix up UCC phy-connection-type properties in the device tree so the PHY gets configured for internal delay on RX only by the OS, as prescribed by mpc8360 rev. 2.1 pb mds erratum #2. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-08mpc83xx: Add the support of MPC837xEMDS boardDave Liu
The MPC837xEMDS board support: * DDR2 400MHz hardcoded and SPD init * Local bus NOR Flash * I2C, UART, MII and RTC * eTSEC RGMII * PCI host Signed-off-by: Dave Liu <daveliu@freescale.com>
2008-01-08MPC8360E-MDS: configure and enable second UARTAnton Vorontsov
Despite user manual, BCSR9.7 is negated (high) on HRST, so UART2 is disabled. Fix that and configure QE pins properly. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-01-07Merge with git://www.denx.de/git/u-boot.gitPeter Pearse
2008-01-05Merge branch 'katmai-ddr-gda'Stefan Roese
2008-01-05ppc4xx: Update Katmai/44x_spd_ddr2.c code for optimal DDR2 setupStefan Roese
On Katmai the complete auto-calibration somehow doesn't seem to produce the best results, meaning optimal values for RQFD/RFFD. This was discovered by GDA using a high bandwidth scope, analyzing the DDR2 signals. GDA provided a fixed value for RQFD, so now on Katmai "only" RFFD is auto-calibrated. This patch also adds RDCC calibration as mentioned on page 7 of the AMCC PowerPC440SP/SPe DDR2 application note: "DDR1/DDR2 Initialization Sequence and Dynamic Tuning" Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-04ppc4xx: Remove sdram.h from PMC440 boardMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-01-04ppc4xx: use common denali core defines and data eye search code for PMC440Matthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-01-04ppc4xx: More cleanup for esd's LCD codeMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-01-04ppc4xx: Use CFG_4xx_GPIO_TABLE to configure Korat boardLawrence R. Johnson
Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-04ppc4xx: Use CFG_4xx_GPIO_TABLE to configure Sequoia boardLawrence R. Johnson
Note: this patch changes the configuration of some GPIO registers: Register Old Value New Value --------------- ---------- ---------- DCR GPIO0_TCR 0x0000000F 0x0000F0CF DCR GPIO0_TSRH 0x55005000 0x00000000 DCR GPIO1_TCR 0xC2000000 0xE2000000 DCR GPIO1_TSRL 0x0C000000 0x00200000 DCR GPIO1_ISR2L 0x00050000 0x00110000 Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-04PPC4xx: Remove sdram.h from board/lwmon5Larry Johnson
These definitions are now in "include/ppc440.h". Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-04PPC4xx: Use common code for LWMON5 board SDRAM supportLarry Johnson
This patch also modifies the functionality of the code so that the data-eye search is now done with with the cache disabled. Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-04PPC4xx: Remove sdram.h from board/amcc/sequoiaLarry Johnson
These definitions are now in "include/ppc440.h". Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-04PPC4xx: Use common code for Sequoia board SDRAM supportLarry Johnson
Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-038610: Move include of config.h earlier.Jon Loeliger
Include config.h earlier in the set of #includes so as to avoid a incidental and duplicate definition of CFG_CACHELINE_SIZE. Signed-off-by: Jon Loeliger
2008-01-03Convert MPC8641HPCN to use libfdt.Jon Loeliger
Assumes the presence of the aliases node in the DTS to locate the ethernet, pci and serial nodes for fixups. Use consistent fdtaddr and fdtfile in environment variables. Signed-off-by: Jon Loeliger <jdl@freescale.com>
2008-01-03Merge commit 'wd/master'Jon Loeliger
2008-01-02Make scripts and Makefiles POSIX compliantWolfgang Denk
The bash builtin versions of the "test" (resp. "[") command allow using "==" for string comparisons, but POSIX compatible implemen- tations (like /usr/bin/test) insist on using "=" only. On such systems you will see: $ /usr/bin/test a == a && echo OK /usr/bin/test: ==: binary operator expected This patch fixes Makefiles and scripts to use POSIX style. Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-12-28ppc4xx: Coding style cleanupStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-28ppc4xx: Add FPGA support and BSP commands for PMC440 boardsMatthias Fuchs
This patch adds some BSP commands and FPGA booting support for esd's PMC440 boards. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2007-12-28ppc4xx: Add initial esd PMC440 board filesMatthias Fuchs
This patch adds the first files for the new esd PMC440 boards. The next two patches will complete the PMC440 board support. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2007-12-28ppc4xx: Add EEPROM write protection for PLU405 boards + misc. updatesMatthias Fuchs
- add EEPROM write protection for esd PLU405 boards. - initialize NAND GPIOs - use correct io accessors - cleanup Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-13 16:20:49 +0000