summaryrefslogtreecommitdiff
path: root/board/keymile
AgeCommit message (Collapse)Author
2013-05-10Fix references to the documentation filesAnatolij Gustschin
Many boot image configuration files refer to the appropriate documentation file, but these references contain typos in the directory and file name. Fix them. Also fix reference to doc/README.SPL file. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2013-03-09powerpc/82xx/km: removed unneeded ifdefHolger Brunck
All boards from this serie uses i2c. So we can drop these unneeded defines. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-03-09powerpc/82xx/km: make handle_mgcoge3un_reset staticHolger Brunck
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15powerpc/83xx/km: drop uneeded dtt_bus environment varHolger Brunck
There is no need for a environment variable to configure the dtt bus. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/scripts: replace hardcoded uImageAndreas Huber
Replace uImage with ${uimage}. If uimage is not set, default it to uImage. Signed-off-by: Andreas Huber <andreas.huber@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15powerpc/83xx/km: add MV88E6122 switch support for kmvect1Karlheinz Jerg
kmvect1 has a UEC2 connection to the piggy board and a UEC0 connection to the switch MV88E6122. This switch has a connection to a frontport ethernet interface. The ethernet port used for network booting is automatically selected by u-boot. If a Piggy is plugged, the Piggy port is selected (UEC2, eth1). If the Piggy isn't present, the Frontport is selected (UEC0, eth0). The switch reset is connected to a GPIO on the PRIO3 board FPGA (GPIO28) and released at startup. Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/common/ivm: rework piggy mac adress offset generationHolger Brunck
For the the kmvect1 board we will also need a functionality to add an offset to the IVMs MAC address, because these board will have two valid ethernet ports for debugging purpose. So move the code to an own function. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km82xx, km83xx: move ethernet_present() from common to cpu specificKarlheinz Jerg
For kmvect1 we need a special solution and for km_arm boards we already have. So move the common code to the architectur specific file. Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/common/ivm: remove CONFIG_SYS_I2C_IVM_BUS related codeHolger Brunck
This define isn't set within our setup files. So we can safely remove the affected code. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/common/ivm: remove obsolete codeHolger Brunck
EEprom_ivm_addr isn't set in our environment, so remove the usage of this. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-02-15km/common: remove unneeded ifdefs for I2CHolger Brunck
All boards from this serie use i2c. There is no need to #ifdef the header. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2013-01-09kirkwood: make MPP arrays static constAlbert ARIBAUD
This saves stack and code memory for local copy, and consumes initialized data memory. For 22 of the 29 kirkwood-based boards, this results in a global saving of about 30 bytes. For 7 of them, it results in an increase of 6 to 14 bytes. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-01-09arm/km: remove duplicate codeValentin Longchamp
This patch removes 2 small portions of board specific code that are duplicated with common ARM code and thus unnecessary. These 2 portions of code concern the mach id that is given by u-boot to the Linux kernel to identify the system's MACH. The first one was the possibility to change the MACH thanks to the 'mach_id' enviroment variable. This is possible thanks to the 'machid' env variable (see arch/arm/lib/bootm.c:boot_jump_linux()). The seconde one is the setting of the bi_arch_number. This is already done in arch/arm/lib/board.c:board_init_f() since km_arm.h does #define CONFIG_MACH_TYPE. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
2013-01-09km/common: cosmetic change reported from checkpatchHolger Brunck
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
2013-01-09arm/km: fix memory settingsHolger Brunck
On kmcoge5un we faced some serious problems with the memory during temperature tests. Reason was that we overwrite some registers for memory settings which have to leave untouched. These where registers 0x20148 , 0x2014c and 0x20154. So writing these registers is prohibited and this patch removes them from all km related config files. Even if the problem was only seen on kmcoge5un. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-10-23km83xx: add common support for km8309 boardsGerlando Falauto
Add support for Keymile boards based on mpc8309 (it would be only kmvect1 for now) Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> [#elseif -> #if to allow kmcoge5ne and kmeter1 to build successfully] Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-10-03arm/km: add mv88e6352 configuration for kmnusaValentin Longchamp
The kmnusa board uses a mv88e6352 switch that is connected to the main eth interface of the kirkwood. Therefore the switch must be configured so that the kirkwood's egiga eth inferface can be used. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Holger Brunck <holger.brunck@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
2012-10-03arm/km: use kw_sdram_size_adjust to adjust SDRAM sizeHolger Brunck
Some boards may differ only in the SDRAM size. This function allows to fix the size accordingly and we can use the same u-boot binary for both boards. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2012-09-03arm/km: remove unused codeHolger Brunck
For some reasons we had an own implementaion of dram_init and dram_init_banksize. This is not needed anymore, use the standard kirkwood functions instead. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
2012-09-03km/ivm: fix string len check to support 7 char board namesValentin Longchamp
The fanless boards now have a 7-digit (XXXXX-F) board name. This triggers a border condition when reading this string in the IVM although this string is smaller than the currenly read string size, but only by 1 character. This patch corrects this by changing the size check condition for string length. It is the same change that was done in the platform for this same bug. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Stefan Bigler <stefan.bigler@keymile.com>
2012-09-01Consolidate bootcount code into drivers/bootcountStefan Roese
This patch moves all bootcount implementations into a common directory: drivers/bootcount. The generic bootcount driver is now usable not only by powerpc platforms, but others as well. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Christian Riesch <christian.riesch@omicron.at> Cc: Manfred Rudigier <manfred.rudigier@omicron.at> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de> Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com> Tested-by: Christian Riesch <christian.riesch@omicron.at> Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-07-31powerpc/82xx: add SDRAM detection for km82xxGerlando Falauto
This patch adds SDRAM detection feature to km82xx boards. To enable this feature, define CONFIG_SYS_SDRAM_LIST as the initializer for an array of struct sdram_conf_s. These structs will expose the bitfields within registers PSDMR and OR1 which have to be different between configurations; common bitfields will be defined, as usual, within CONFIG_SYS_PSDMR and CONFIG_SYS_OR1. If CONFIG_SYS_SDRAM_LIST is not defined, then the usual behavior is retained. Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
2012-07-31km/common: remove printfs for i2c deblocking codeHolger Brunck
This code will also be used before reallocation and during this time we are not allowed to do these printings. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Prafulla Wadaskar <Prafulla@marvell.com> Acked-by: Heiko Schocher <hs@denx.de>
2012-07-29doc: cleanup - move board READMEs into respective board directoriesWolfgang Denk
Also drop a few files referring to no longer / not yet supported boards. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Stefan Roese <sr@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: Andy Fleming <afleming@gmail.com> Cc: Jason Jin <jason.jin@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2012-07-10Minor Coding Style cleanupWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-07-07arm/km: remove calls to kw_gpio_* in board_early_init_fHolger Brunck
These functions tried to access two static tables before relocation (board_early_init_f is executed before relocation). But these static tables lie in the bss section which is not valid before relocation. These accesses then overwrote some parts of u-boot binary before it was relocated. For the kmnusa build, this results in a corrupted important env variable (bootcmd) but it may be that some other parts of the u-boot binary are corrupted. This patch solves this problem by moving all the kw_gpio_* calls to board_init, which should be early enough in the boot sequence. The only calls that could not be moved is the one for the SOFT (bitbang) I2C, and they have been replaced by a direct access to the GPIO dataout Control register to set the two GPIOs as output. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: add implementation for read_dip_switchThomas Herzmann
Add a function to read the dip_switch on kmcoge5un. If the switch is set the actual_bank is set to 0 and this SW is booted. Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2012-07-07arm/km: support the 2 PCIe fpga resetsValentin Longchamp
The PCIe FPGAs now have to support 2 resets: one for the non traffic affecting part (PCIe) and one for the traffic affecting part. When the FPGA is not reconfigured, we only reset the PCIe part. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2012-07-07arm/km: skip FPGA config when already configuredValentin Longchamp
In order to be able to perform board resets without interrupting the traffic, the configuration of an already properly configured FPGA is skipped. This is because some PCIe FPGAs embed some other function that must continue to work over reset. It is then the responsibility of the application to trigger a reconfiguration when needed. This is done by lowering the FPGA_INIT_B pin for delaying the configuration to u-boot @ next reboot, and then lower the FPGA_PROGRAM_B signal. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2012-07-07arm/km: redefine piggy 4 reg names to avoid conflictsValentin Longchamp
Some very similar #defines for reg addresses are used in a later patch (managed_switch support for km_arm). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: enable BOCO2 FPGA download supportValentin Longchamp
This adds a first support of the FPGA download for a PCIe FPGA based on the BOCO2 CPLD. This takes place in 3 steps, all done accessing the SPICTRL reg of the BOCO2: 1) start the FPGA config with an access to the FPGA_PROG bit 2) later in the boot sequence, wait for the FPGA_DONE bit to toggle to 1 for the end of the FPGA configuration (with a timeout) 3) reset the FPGA 4) finally remove the access to its config EEPROM from the FPGA so that the CPU can update the FPGA configuration when the kernel is running The boards with a PCIe FPGA but without BOCO2 still are supported. The config option name is CONFIG_KM_FPGA_CONFIG Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: remove portl2.h and use km_kirkwood insteadHolger Brunck
The additional headerfile is unneeded here, we can use the generic km_kirkwood.h instead. And we can use the better config option KM_PIGGY4_88E6061 for the specific features for boards with this design in km_arm.c. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: convert mgcoge3un target to km_kirkwoodHolger Brunck
Use the generic header km_kirkwood.h and get rid of the board specific header. changes for v2: rebased because of changes in other patches Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: add kmcoge5un board supportHolger Brunck
For u-boot this board is similar to mgcoge3un. But some differences are present. We have a different SDRAM on it and therefore a new SDRAM config file. Additionaly this board has a direct MAC/MAC connection from the kirkwood to a marvell simple switch without a phy inbetween, this needs a new configuration for the mvgbe driver. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: add kmnusa board supportHolger Brunck
This board is similar to portl2, but it has the u-boot environment in a SPI NOR flash and not in an i2c eeprom like portl2 have. Some other details: - IVM EEPROM is at adress: pca9547:70:9 - PCI is enabled - PIGGY4 is connected via MV88E6352 simple switch. There is no phy between the simple switch and the kirkwood. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: use spi claim bus to switch between SPI and NANDValentin Longchamp
We overwrite these weak functions from the kirkwood spi code to use our own method to be able to switch between the SPI NOR and the NAND flash. This is needed e.g. to update the u-boot. The former command do_spi_toggle can therefore be removed. And the usage of this command is removed from the u-boot update command in the u-boot environment. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07kirkwood: fix calls to kirkwood_mpp_confValentin Longchamp
With the new second save argument introduced by the previous patch, all the calls to the function had to be fixed. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: fix wrong comment in SDRAM config for mgcoge3unHolger Brunck
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07arm/km: use ARRAY_SIZE macroHolger Brunck
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-06-15km/common: check test_bank and testpin for testbootThomas Herzmann
If the testpin is asserted, first check if a test_bank variable is defined before trying to boot this test_bank. Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15powerpc/83xx/km: readout dip_switch on kmcoge5neThomas Herzmann
On kmcoge5ne we have a dip switch present. If this switch was switched on the actual_bank is set to 0 and this SW will be booted. Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15powerpc/83xx: configure CONFIG_POST for kmcoge5neThomas Herzmann
kmcoge5ne starts the post tests if the testpin on the board was enabled. Currently it does simply a memory test. Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15powerpc/83xx/km: added missing enable of application bufferStefan Bigler
Enabled application buffers in uboot to allow application chipselect access in uboot. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15km/common: fixed error in ethaddr (1-byte-shift)Thomas Herzmann
The MAC address begins at offset 1. Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15powerpc/83xx: add kmcoge5ne board supportHolger Brunck
This board is a MPC8360 board. Two flashes are present a NOR flash were u-boot and the u-boot environment is stored and a NAND flash for the application code. This board has 512MB SDRAM. Additionaly we introduce a common km8360.h file and convert kmeter1 to use this. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Christian Herzig <christian.herzig@keymile.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15powerpc83xx/km: lock the window size to 2GiB befor fixing sdram sizeChristian Herzig
If the ram size isn't locked to 2GiB, the get_ram_size() may hang up. Signed-off-by: Christian Herzig <christian.herzig@keymile.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-02-12arm/km: checkpatch cleanupHolger Brunck
Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: Heiko Schocher <hs@denx.de>
2011-12-20km/common: add toolchain variableHolger Brunck
Add a variable "toolchain" and configure the rootpath for the nfsargs with this variable. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Wolfgang Denk <wd@denx.de>
2011-12-07Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk
* 'master' of git://git.denx.de/u-boot-mpc83xx: powerpc/83xx: fix sdram initialization for keymile boards powerpc/mpc83xx: cleanup makefile for mpc83xx
2011-11-16mpc83xx: km83xx_i2c - fix gcc 4.6 compiler warningKim Phillips
Configuring for kmeter1 board... km83xx_i2c.c: In function 'i2c_make_abort': km83xx_i2c.c:44:8: warning: variable 'dummy' set but not used [-Wunused-but-set-variable] Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Heiko Schocher <hs@denx.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-04 17:18:34 +0000