summaryrefslogtreecommitdiff
path: root/board/freescale
AgeCommit message (Collapse)Author
2016-03-21armv8/ls1043aqds: Return i2c mux to default chennelWenbin Song
Return i2c mux to the default channel after accessing retimer. Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-21freescale: vid: Return i2c mux to default channelWenbin Song
IR chip is on one of the channels on multiplexed I2C-bus. Reset to default channel after accessing. Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-21armv8: ls2085a: Remove phy configuration from QDS and RDBPrabhakar Kushwaha
As phy_connect and phy_config are being called from DPAA2 driver. Remove calling of mentioned function from board file. Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-21armv8: ls2080ardb: invert irq pins polarity for AQR405 PHYShaohui Xie
To use AQR405 PHY's interrupt, we need to invert the relative IRQ pins polarity by setting IRQCR register, because AQR405 interrupt is low active but GIC accepts high active. Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-14Kconfig: Move CONFIG_FIT and related options to KconfigSimon Glass
There are already two FIT options in Kconfig but the CONFIG options are still in the header files. We need to do a proper move to fix this. Move these options to Kconfig and tidy up board configuration: CONFIG_FIT CONFIG_OF_BOARD_SETUP CONFIG_OF_SYSTEM_SETUP CONFIG_FIT_SIGNATURE CONFIG_FIT_BEST_MATCH CONFIG_FIT_VERBOSE CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_RSA Unfortunately the first one is a little complicated. We need to make sure this option is not enabled in SPL by this change. Also this option is enabled automatically in the host builds by defining CONFIG_FIT in the image.h file. To solve this, add a new IMAGE_USE_FIT #define which can be used in files that are built on the host but must also build for U-Boot and SPL. Note: Masahiro's moveconfig.py script is amazing. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Add microblaze change, various configs/ re-applies] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-13mx6slevk: Fix the power up of the Ethernet PHYFabio Estevam
GPIO4_21 is the LAN8720 power pin, not the LAN8720 reset pin. Fix that, so that we can have Ethernet functional again. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-03-02mx6qarm2: Update maintainer's emailsFabio Estevam
Use the new NXP emails. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-03-02MAINTAINERS: Update Peng Fan's email addressFabio Estevam
Use Peng Fan's new NXP email address in MAINTAINERS files. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2016-02-24armv7: ls102xa: Move smmu and stream id initialization into the common soc codeAlison Wang
The initialization for smmu and stream id is moved into the common soc code. Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24board: ls1043ardb: Modify pin-muxing code for USB and QE-HDLCZhao Qiang
QE-HDLC and USB multi-use the pins, modify the pin-muxing code for them, when set "hwconfig=qe-hdlc" in uboot, assign the pins to QE-HDLC, if not, assgin it to USB Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24board: ls1043rdb: Move USB muxing config to config_board_muxZhao Qiang
Pin-muxing code should be in config_board_mux, move USB muxing config to config_board_mux. Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24board: ls1043ardb: Add micro QE support for ls1043ardbZhao Qiang
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24armv8/ls1043aqds: Add USB support for ls1043aqdsQianyu Gong
Add USB XHCI support for ls1043qds board. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24qe: move drivers/qe/qe.h to include/fsl_qe.hQianyu Gong
As the QE firmware struct is shared with Fman, move the header file out of drivers/qe/. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24arm: ls1021a: Add QSPI or IFC support in SD boot for LS1021AQDS boardAlison Wang
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported in SD boot now. For the customer's demand, QSPI needs to be supported in SD boot too. This patch adds QSPI or IFC support in SD boot according to the corresponding defconfig. For detail, ls1021aqds_sdcard_ifc_defconfig is used to support IFC in SD boot and ls1021aqds_sdcard_qspi_defconfig is used to support QSPI in SD boot. Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-21Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2016-02-21mx7dsabresd: Make 'ums' command functionalFabio Estevam
When running the 'ums' command we get: => ums 0 mmc 0 UMS: disk start sector: 0x0, count: 0xe18000 g_dnl_register: failed!, error: -22 ERROR: g_dnl_register failed at common/cmd_usb_mass_storage.c:107/do_usb_mass_storage() Fix this by initializing USB OTG1 port as USB device mode instead of host. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-21mx7dsabresd: Use Adrian's NXP email addressFabio Estevam
Use the new NXP email address for the board maintainer. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-06Use correct spelling of "U-Boot"Bin Meng
Correct spelling of "U-Boot" shall be used in all written text (documentation, comments in source files etc.). Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-04imx: mx6: implement board_mmc_get_env_devPeng Fan
Implement board_mmc_get_env_dev for the boards. Following is examples: SD1/SD2/SD3: return devno; SD2/SD3: return devno - 1; SD2/SD4: if (devno == 2), return dev - 2; return dev - 1; Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-02-04imx: mx7dsabresd: move mmc_get_env_devno to soc codePeng Fan
Move mmc_get_env_devno to soc.c and rename to mmc_get_env_dev to match the one in common/env_mmc.c. Introduce a weak function board_mmc_get_env_dev. Different boards can implement this according to sdhc controller which is used by the board. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-02-02imx: mx6sxsabresd: Add MCIMX28LCD display supportYe Li
The i.MX6SX SABRESD board supports MCIMX28LCD (800x480x24) at LCDIF1 port, enable this display feature by adding relevant BSP codes and configurations. Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02imx: MX6DQ{P}/DL:SABRESD Fix bmode eMMC failureYe Li
The BOOTCFG value used by bmode for SABRESD eMMC boot are actually for SD card. Fixed the value to correct one. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02mx6slevk: Fix the reset delay for the the LAN8720 PHYFabio Estevam
Since commit 59370f3fcd1350 ("net: phy: delay only if reset handler is registered") Ethernet is no longer functional. This commit does not have an issue in itself, but it revelead a problem with the Ethernet initialization. According to the LAN8720 datasheet tpurstd (time that reset line should stay asserted) is 25ms. So do as suggested in order to have Ethernet working again. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02imx: mx6sxsabreauto: Add support for mx6sx SABREAUTO boardYe Li
Initial version for mx6sx SABREAUTO board support with features: PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander. Signed-off-by: Ye Li <ye.li@nxp.com>
2016-01-28Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini
2016-01-28arm: ls1021atwr: Do not wrap pci_eth_init() with CONFIG_TSEC_ENETBin Meng
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28powerpc: p1010rdb: Do not wrap pci_eth_init() with CONFIG_TSEC_ENETBin Meng
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28powerpc: mpc8548cds: Do not wrap pci_eth_init() with CONFIG_TSEC_ENETBin Meng
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28powerpc: mpc8572ds: Do not wrap pci_eth_init() with CONFIG_TSEC_ENETBin Meng
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28powerpc: c29xpcie: Do not wrap pci_eth_init() with CONFIG_TSEC_ENETBin Meng
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28powerpc: bsc9132qds: Do not wrap pci_eth_init() with CONFIG_TSEC_ENETBin Meng
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-01-27armv8/ls1043aqds: add QSPI boot supportQianyu Gong
Enable the U-Boot Driver Model(DM) to use the Freescale QSPI driver. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27armv8/ls1043aqds: add QSPI support in SD bootGong Qianyu
QSPI and IFC are pin-multiplexed on LS1043A. So we use ls1043aqds_sdcard_ifc_defconfig to support IFC in SD boot and ls1043aqds_sdcard_qspi_defconfig to support QSPI in SD boot. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27armv8/ls1043aqds: Select lpuart pins of various muxesShaohui Xie
Set Board Configuration Register to select the lpuart pins of various muxes. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27secure_boot: change error handler for esbc_validateAneesh Bansal
In case of error while executing esbc_validate command, SNVS transition and issue of reset is required only for secure-boot. If boot mode is non-secure, this is not required. Similarly, esbc_halt command which puts the core in Spin Loop is applicable only for Secure Boot. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27secure_boot: enable chain of trust for ARM platformsAneesh Bansal
Chain of Trust is enabled for ARM platforms (LS1021 and LS1043). In board_late_init(), fsl_setenv_chain_of_trust() is called which will perform the following: - If boot mode is non-secure, return (No Change) - If boot mode is secure, set the following environmet variables: bootdelay = 0 (To disable Boot Prompt) bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script) Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27secure_boot: create function to determine boot modeAneesh Bansal
A function is created to detrmine if the boot mode is secure or non-secure for differnt SoC's. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini
2016-01-25powerpc/board/t4240rdb: Enable VID supportYing Zhang
The fuse status register provides the values from on-chip voltage ID efuses programmed at the factory. These values define the voltage requirements for the chip. u-boot reads FUSESR and translates the values into the appropriate commands to set the voltage output value of an external voltage regulator. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25board/freescale/common: Check IR chip mode for VID supportYing Zhang
IR chip on all the boards are required to be used in Intel mode to support VID. VDD will not be adjusted if IR chip is used in other modes. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25powerpc: mpc85xx: Move set_liodns, setup_portals to common boot seqPrabhakar Kushwaha
Users migrating Freescale's PowerPC SoC U-Boot code to their custom board, often overlook the need to execute set_liodns() and setup_portals() being called by platform files. So Move set_liodns() and setup_portals() to common u-boot boot sequence Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25SECURE BOOT: support for validation of dynamic imageAneesh Bansal
Some images to be validated are relocated to a dynamic address at run time. So, these addresses cannot be known befor hand while signing the images and creating the header offline. So, support is required to pass the image address to the validate function as an argument. If an address is provided to the function, the address field in Header is not read and is treated as a reserved field. Signed-off-by: Saksham Jain <saksham@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25SECURE BOOT: separate function created for signatureAneesh Bansal
The code for image hash calculation, hash calculation from RSA signature and comparison of hashes has been mobed to a separate function. Signed-off-by: Saksham Jain <saksham@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25SECURE BOOT: separate functions for reading keysAneesh Bansal
Separate functions are created for reading and checking the sanity of Public keys: - read_validate_single_key - read_validate_ie_tbl - read_validate_srk_table Signed-off-by: Saksham Jain <saksham@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25SECURE BOOT: change prototype of fsl_secboot_validate functionAneesh Bansal
The prototype and defination of function fsl_secboot_validate has been changed to support calling this function from another function within u-boot. Only two aruments needed: 1) header address - Mandatory 2) SHA256 string - optional Signed-off-by: Saksham Jain <saksham@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25freescale/qixis: Add support for booting from SD/QSPIGong Qianyu
1.Use "qixis_reset sd" to boot from SD 2.Use "qixis_reset sd_qspi" to boot from SD with QSPI support 3.Use "qixis_reset qspi" to boot from QSPI flash On some SoCs such as LS1021A and LS1043A, IFC and QSPI could be pin-multiplexed. So the switches are different between SD boot with IFC support and SD boot with QSPI support. The default booting from SD is with IFC support. Once QSPI is enabled(IFC disabled), only use I2C to access QIXIS. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25armv8/ls1043aqds: Add support for >2GB memoryShaohui Xie
This patch also exposes the complete DDR region(s) to Linux. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-24imx: mx7dsabresd: support nandPeng Fan
Add pinmux settings. Add related macro definitions. Nand pin conflicts with emmc, so if want to enable nand, need to do hardware rework. After hardware rework, define CONFIG_NAND_MXS in board header file. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-05-26 02:54:42 +0000