diff options
Diffstat (limited to 'board/solidrun')
| -rw-r--r-- | board/solidrun/mx6cuboxi/mx6cuboxi.c | 101 |
1 files changed, 100 insertions, 1 deletions
diff --git a/board/solidrun/mx6cuboxi/mx6cuboxi.c b/board/solidrun/mx6cuboxi/mx6cuboxi.c index d3a32c1663..eab92f125c 100644 --- a/board/solidrun/mx6cuboxi/mx6cuboxi.c +++ b/board/solidrun/mx6cuboxi/mx6cuboxi.c @@ -18,9 +18,11 @@ #include <asm/arch/imx-regs.h> #include <asm/arch/iomux.h> #include <asm/arch/mx6-pins.h> +#include <asm/arch/mxc_hdmi.h> #include <asm/errno.h> #include <asm/gpio.h> #include <asm/imx-common/iomux-v3.h> +#include <asm/imx-common/video.h> #include <mmc.h> #include <fsl_esdhc.h> #include <miiphy.h> @@ -159,10 +161,107 @@ int board_eth_init(bd_t *bis) return cpu_eth_init(bis); } +#ifdef CONFIG_VIDEO_IPUV3 +static void do_enable_hdmi(struct display_info_t const *dev) +{ + imx_enable_hdmi_phy(); +} + +struct display_info_t const displays[] = { + { + .bus = -1, + .addr = 0, + .pixfmt = IPU_PIX_FMT_RGB24, + .detect = detect_hdmi, + .enable = do_enable_hdmi, + .mode = { + .name = "HDMI", + /* 1024x768@60Hz (VESA)*/ + .refresh = 60, + .xres = 1024, + .yres = 768, + .pixclock = 15384, + .left_margin = 160, + .right_margin = 24, + .upper_margin = 29, + .lower_margin = 3, + .hsync_len = 136, + .vsync_len = 6, + .sync = FB_SYNC_EXT, + .vmode = FB_VMODE_NONINTERLACED + } + } +}; + +size_t display_count = ARRAY_SIZE(displays); + +static int setup_display(void) +{ + struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + int reg; + int timeout = 100000; + + enable_ipu_clock(); + imx_setup_hdmi(); + + /* set video pll to 455MHz (24MHz * (37+11/12) / 2) */ + setbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN); + + reg = readl(&ccm->analog_pll_video); + reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT; + reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(37); + reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT; + reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(1); + writel(reg, &ccm->analog_pll_video); + + writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num); + writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom); + + reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN; + writel(reg, &ccm->analog_pll_video); + + while (timeout--) + if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK) + break; + if (timeout < 0) { + printf("Warning: video pll lock timeout!\n"); + return -ETIMEDOUT; + } + + reg = readl(&ccm->analog_pll_video); + reg |= BM_ANADIG_PLL_VIDEO_ENABLE; + reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS; + writel(reg, &ccm->analog_pll_video); + + /* gate ipu1_di0_clk */ + clrbits_le32(&ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK); + + /* select video_pll clock / 7 for ipu1_di0_clk -> 65MHz pixclock */ + reg = readl(&ccm->chsccdr); + reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK | + MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK | + MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK); + reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET) | + (6 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) | + (0 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); + writel(reg, &ccm->chsccdr); + + /* enable ipu1_di0_clk */ + setbits_le32(&ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK); + + return 0; +} +#endif /* CONFIG_VIDEO_IPUV3 */ + int board_early_init_f(void) { + int ret = 0; setup_iomux_uart(); - return 0; + +#ifdef CONFIG_VIDEO_IPUV3 + ret = setup_display(); +#endif + return ret; } int board_init(void) |