diff options
Diffstat (limited to 'arch/blackfin/cpu/serial.h')
| -rw-r--r-- | arch/blackfin/cpu/serial.h | 222 |
1 files changed, 16 insertions, 206 deletions
diff --git a/arch/blackfin/cpu/serial.h b/arch/blackfin/cpu/serial.h index 8a076ddc92..9200339668 100644 --- a/arch/blackfin/cpu/serial.h +++ b/arch/blackfin/cpu/serial.h @@ -3,7 +3,7 @@ * any functions defined here must be always_inline since * initcode cannot have function calls. * - * Copyright (c) 2004-2007 Analog Devices Inc. + * Copyright (c) 2004-2011 Analog Devices Inc. * * Licensed under the GPL-2 or later. */ @@ -12,7 +12,7 @@ #define __BFIN_CPU_SERIAL_H__ #include <asm/blackfin.h> -#include <asm/mach-common/bits/uart.h> +#include <asm/portmux.h> #ifndef CONFIG_UART_CONSOLE # define CONFIG_UART_CONSOLE 0 @@ -24,88 +24,34 @@ # define BFIN_DEBUG_EARLY_SERIAL 0 #endif -#ifndef __ASSEMBLY__ - -#include <asm/portmux.h> - -#define LOB(x) ((x) & 0xFF) -#define HIB(x) (((x) >> 8) & 0xFF) - -#if defined(__ADSPBF50x__) || defined(__ADSPBF54x__) +#if defined(__ADSPBF60x__) +# define BFIN_UART_HW_VER 4 +#elif defined(__ADSPBF50x__) || defined(__ADSPBF54x__) # define BFIN_UART_HW_VER 2 #else # define BFIN_UART_HW_VER 1 #endif -/* - * All Blackfin system MMRs are padded to 32bits even if the register - * itself is only 16bits. So use a helper macro to streamline this. - */ -#define __BFP(m) u16 m; u16 __pad_##m -struct bfin_mmr_serial { -#if BFIN_UART_HW_VER == 2 - __BFP(dll); - __BFP(dlh); - __BFP(gctl); - __BFP(lcr); - __BFP(mcr); - __BFP(lsr); - __BFP(msr); - __BFP(scr); - __BFP(ier_set); - __BFP(ier_clear); - __BFP(thr); - __BFP(rbr); -#else - union { - u16 dll; - u16 thr; - const u16 rbr; - }; - const u16 __spad0; - union { - u16 dlh; - u16 ier; - }; - const u16 __spad1; - const __BFP(iir); - __BFP(lcr); - __BFP(mcr); - __BFP(lsr); - __BFP(msr); - __BFP(scr); - const u32 __spad2; - __BFP(gctl); -#endif -}; -#undef __BFP - #define __PASTE_UART(num, pfx, sfx) pfx##num##_##sfx #define _PASTE_UART(num, pfx, sfx) __PASTE_UART(num, pfx, sfx) -#define MMR_UART(n) _PASTE_UART(n, UART, DLL) #define _P_UART(n, pin) _PASTE_UART(n, P_UART, pin) #define P_UART(pin) _P_UART(CONFIG_UART_CONSOLE, pin) -#ifndef UART_DLL -# define UART_DLL MMR_UART(CONFIG_UART_CONSOLE) -#else -# define UART0_DLL UART_DLL -# if CONFIG_UART_CONSOLE != 0 -# error CONFIG_UART_CONSOLE must be 0 on parts with only one UART -# endif -#endif #define pUART ((volatile struct bfin_mmr_serial *)uart_base) -#if BFIN_UART_HW_VER == 2 -# define ACCESS_LATCH() -# define ACCESS_PORT_IER() +#ifndef __ASSEMBLY__ +__attribute__((always_inline)) +static inline void serial_do_portmux(void); +#endif + +#if BFIN_UART_HW_VER < 4 +# include "serial1.h" #else -# define ACCESS_LATCH() \ - bfin_write(&pUART->lcr, bfin_read(&pUART->lcr) | DLAB) -# define ACCESS_PORT_IER() \ - bfin_write(&pUART->lcr, bfin_read(&pUART->lcr) & ~DLAB) +# include "serial4.h" #endif +#ifndef __ASSEMBLY__ + __attribute__((always_inline)) static inline void serial_do_portmux(void) { @@ -115,143 +61,7 @@ static inline void serial_do_portmux(void) return; } -#if defined(__ADSPBF50x__) -# define DO_MUX(port, mux_tx, mux_rx, tx, rx) \ - bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & ~(PORT_x_MUX_##mux_tx##_MASK | PORT_x_MUX_##mux_rx##_MASK)) | PORT_x_MUX_##mux_tx##_FUNC_1 | PORT_x_MUX_##mux_rx##_FUNC_1); \ - bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx | P##port##rx); - switch (CONFIG_UART_CONSOLE) { - case 0: DO_MUX(G, 7, 7, 12, 13); break; /* Port G; mux 7; PG12 and PG13 */ - case 1: DO_MUX(F, 3, 3, 6, 7); break; /* Port F; mux 3; PF6 and PF7 */ - } - SSYNC(); -#elif defined(__ADSPBF51x__) -# define DO_MUX(port, mux_tx, mux_rx, tx, rx) \ - bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & ~(PORT_x_MUX_##mux_tx##_MASK | PORT_x_MUX_##mux_rx##_MASK)) | PORT_x_MUX_##mux_tx##_FUNC_2 | PORT_x_MUX_##mux_rx##_FUNC_2); \ - bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx | P##port##rx); - switch (CONFIG_UART_CONSOLE) { - case 0: DO_MUX(G, 5, 5, 9, 10); break; /* Port G; mux 5; PG9 and PG10 */ - case 1: DO_MUX(F, 2, 3, 14, 15); break; /* Port H; mux 2/3; PH14 and PH15 */ - } - SSYNC(); -#elif defined(__ADSPBF52x__) -# define DO_MUX(port, mux, tx, rx) \ - bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & ~PORT_x_MUX_##mux##_MASK) | PORT_x_MUX_##mux##_FUNC_3); \ - bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx | P##port##rx); - switch (CONFIG_UART_CONSOLE) { - case 0: DO_MUX(G, 2, 7, 8); break; /* Port G; mux 2; PG2 and PG8 */ - case 1: DO_MUX(F, 5, 14, 15); break; /* Port F; mux 5; PF14 and PF15 */ - } - SSYNC(); -#elif defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__) - const uint16_t func[] = { PFDE, PFTE, }; - bfin_write_PORT_MUX(bfin_read_PORT_MUX() & ~func[CONFIG_UART_CONSOLE]); - bfin_write_PORTF_FER(bfin_read_PORTF_FER() | - (1 << P_IDENT(P_UART(RX))) | - (1 << P_IDENT(P_UART(TX)))); - SSYNC(); -#elif defined(__ADSPBF54x__) -# define DO_MUX(port, tx, rx) \ - bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & ~(PORT_x_MUX_##tx##_MASK | PORT_x_MUX_##rx##_MASK)) | PORT_x_MUX_##tx##_FUNC_1 | PORT_x_MUX_##rx##_FUNC_1); \ - bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx | P##port##rx); - switch (CONFIG_UART_CONSOLE) { - case 0: DO_MUX(E, 7, 8); break; /* Port E; PE7 and PE8 */ - case 1: DO_MUX(H, 0, 1); break; /* Port H; PH0 and PH1 */ - case 2: DO_MUX(B, 4, 5); break; /* Port B; PB4 and PB5 */ - case 3: DO_MUX(B, 6, 7); break; /* Port B; PB6 and PB7 */ - } - SSYNC(); -#elif defined(__ADSPBF561__) - /* UART pins could be GPIO, but they aren't pin muxed. */ -#else -# if (P_UART(RX) & P_DEFINED) || (P_UART(TX) & P_DEFINED) -# error "missing portmux logic for UART" -# endif -#endif -} - -__attribute__((always_inline)) -static inline int uart_init(uint32_t uart_base) -{ - /* always enable UART -- avoids anomalies 05000309 and 05000350 */ - bfin_write(&pUART->gctl, UCEN); - - /* Set LCR to Word Lengh 8-bit word select */ - bfin_write(&pUART->lcr, WLS_8); - - SSYNC(); - - return 0; -} - -__attribute__((always_inline)) -static inline int serial_early_init(uint32_t uart_base) -{ - /* handle portmux crap on different Blackfins */ - serial_do_portmux(); - - return uart_init(uart_base); -} - -__attribute__((always_inline)) -static inline int serial_early_uninit(uint32_t uart_base) -{ - /* disable the UART by clearing UCEN */ - bfin_write(&pUART->gctl, 0); - - return 0; -} - -__attribute__((always_inline)) -static inline void serial_early_put_div(uint32_t uart_base, uint16_t divisor) -{ - /* Set DLAB in LCR to Access DLL and DLH */ - ACCESS_LATCH(); - SSYNC(); - - /* Program the divisor to get the baud rate we want */ - bfin_write(&pUART->dll, LOB(divisor)); - bfin_write(&pUART->dlh, HIB(divisor)); - SSYNC(); - - /* Clear DLAB in LCR to Access THR RBR IER */ - ACCESS_PORT_IER(); - SSYNC(); -} - -__attribute__((always_inline)) -static inline uint16_t serial_early_get_div(void) -{ - uint32_t uart_base = UART_DLL; - - /* Set DLAB in LCR to Access DLL and DLH */ - ACCESS_LATCH(); - SSYNC(); - - uint8_t dll = bfin_read(&pUART->dll); - uint8_t dlh = bfin_read(&pUART->dlh); - uint16_t divisor = (dlh << 8) | dll; - - /* Clear DLAB in LCR to Access THR RBR IER */ - ACCESS_PORT_IER(); - SSYNC(); - - return divisor; -} - -/* We cannot use get_sclk() early on as it uses caches in external memory */ -#if defined(BFIN_IN_INITCODE) || defined(CONFIG_DEBUG_EARLY_SERIAL) -# define get_sclk() (CONFIG_CLKIN_HZ * CONFIG_VCO_MULT / CONFIG_SCLK_DIV) -#endif - -__attribute__((always_inline)) -static inline void serial_early_set_baud(uint32_t uart_base, uint32_t baud) -{ - /* Translate from baud into divisor in terms of SCLK. The - * weird multiplication is to make sure we over sample just - * a little rather than under sample the incoming signals. - */ - serial_early_put_div(uart_base, - (get_sclk() + (baud * 8)) / (baud * 16) - ANOMALY_05000230); + serial_early_do_portmux(); } #ifndef BFIN_IN_INITCODE |