diff options
Diffstat (limited to 'README')
| -rw-r--r-- | README | 67 |
1 files changed, 65 insertions, 2 deletions
@@ -485,6 +485,17 @@ The following options need to be configured: Thumb2 this flag will result in Thumb2 code generated by GCC. + CONFIG_ARM_ERRATA_716044 + CONFIG_ARM_ERRATA_742230 + CONFIG_ARM_ERRATA_743622 + CONFIG_ARM_ERRATA_751472 + + If set, the workarounds for these ARM errata are applied early + during U-Boot startup. Note that these options force the + workarounds to be applied; no CPU-type/version detection + exists, unlike the similar options in the Linux kernel. Do not + set these options unless they apply! + - Linux Kernel Interface: CONFIG_CLOCKS_IN_MHZ @@ -842,7 +853,8 @@ The following options need to be configured: CONFIG_CMD_I2C * I2C serial bus support CONFIG_CMD_IDE * IDE harddisk support CONFIG_CMD_IMI iminfo - CONFIG_CMD_IMLS List all found images + CONFIG_CMD_IMLS List all images found in NOR flash + CONFIG_CMD_IMLS_NAND List all images found in NAND flash CONFIG_CMD_IMMAP * IMMR dump support CONFIG_CMD_IMPORTENV * import an environment CONFIG_CMD_INI * import data from an ini file into the env @@ -859,7 +871,8 @@ The following options need to be configured: (requires CONFIG_CMD_MEMORY and CONFIG_MD5) CONFIG_CMD_MEMINFO * Display detailed memory information CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base, - loop, loopw, mtest + loop, loopw + CONFIG_CMD_MEMTEST mtest CONFIG_CMD_MISC Misc functions like sleep etc CONFIG_CMD_MMC * MMC memory mapped support CONFIG_CMD_MII * MII utility commands @@ -876,6 +889,7 @@ The following options need to be configured: CONFIG_CMD_READ * Read raw data from partition CONFIG_CMD_REGINFO * Register dump CONFIG_CMD_RUN run command in env variable + CONFIG_CMD_SANDBOX * sb command to access sandbox features CONFIG_CMD_SAVES * save S record dump CONFIG_CMD_SCSI * SCSI Support CONFIG_CMD_SDRAM * print SDRAM configuration information @@ -1530,6 +1544,17 @@ CBFS (Coreboot Filesystem) support allows for a "silent" boot where a splash screen is loaded very quickly after power-on. + CONFIG_SPLASHIMAGE_GUARD + + If this option is set, then U-Boot will prevent the environment + variable "splashimage" from being set to a problematic address + (see README.displaying-bmps and README.arm-unaligned-accesses). + This option is useful for targets where, due to alignment + restrictions, an improperly aligned BMP image will cause a data + abort. If you think you will not have problems with unaligned + accesses (for example because your toolchain prevents them) + there is no need to set this option. + CONFIG_SPLASH_SCREEN_ALIGN If this option is set the splash image can be freely positioned @@ -1550,6 +1575,14 @@ CBFS (Coreboot Filesystem) support => vertically centered image at x = dspWidth - bmpWidth - 9 + CONFIG_SPLASH_SCREEN_PREPARE + + If this option is set then the board_splash_screen_prepare() + function, which must be defined in your code, is called as part + of the splash screen display sequence. It gives the board an + opportunity to prepare the splash image data before it is + processed and sent to the frame buffer by U-Boot. + - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP If this option is set, additionally to standard BMP @@ -3209,6 +3242,23 @@ Configuration Settings: If defined, don't allow the -f switch to env set override variable access flags. +- CONFIG_SYS_GENERIC_BOARD + This selects the architecture-generic board system instead of the + architecture-specific board files. It is intended to move boards + to this new framework over time. Defining this will disable the + arch/foo/lib/board.c file and use common/board_f.c and + common/board_r.c instead. To use this option your architecture + must support it (i.e. must define __HAVE_ARCH_GENERIC_BOARD in + its config.mk file). If you find problems enabling this option on + your board please report the problem and send patches! + +- CONFIG_SYS_SYM_OFFSETS + This is set by architectures that use offsets for link symbols + instead of absolute values. So bss_start is obtained using an + offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than + directly. You should not need to touch this setting. + + The following definitions that deal with the placement and management of environment data (variable area); in general, we support the following configurations: @@ -3810,6 +3860,15 @@ Low Level (hardware related) configuration options: that is executed before the actual U-Boot. E.g. when compiling a NAND SPL. +- CONFIG_ARCH_MAP_SYSMEM + Generally U-Boot (and in particular the md command) uses + effective address. It is therefore not necessary to regard + U-Boot address as virtual addresses that need to be translated + to physical addresses. However, sandbox requires this, since + it maintains its own little RAM buffer which contains all + addressable memory. This option causes some memory accesses + to be mapped through map_sysmem() / unmap_sysmem(). + - CONFIG_USE_ARCH_MEMCPY CONFIG_USE_ARCH_MEMSET If these options are used a optimized version of memcpy/memset will @@ -3820,6 +3879,10 @@ Low Level (hardware related) configuration options: If defined, the x86 reset vector code is included. This is not needed when U-Boot is running from Coreboot. +- CONFIG_SYS_MPUCLK + Defines the MPU clock speed (in MHz). + + NOTE : currently only supported on AM335x platforms. Freescale QE/FMAN Firmware Support: ----------------------------------- |