summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--MAINTAINERS4
-rw-r--r--arch/arm/cpu/armv7/exynos/power.c45
-rw-r--r--arch/arm/dts/exynos5250.dtsi5
-rw-r--r--arch/arm/include/asm/arch-exynos/power.h24
-rw-r--r--arch/arm/include/asm/arch-exynos/spl.h3
-rw-r--r--arch/arm/include/asm/arch-exynos/tmu.h58
-rw-r--r--board/samsung/dts/exynos5250-smdk5250.dts13
-rw-r--r--board/samsung/dts/exynos5250-snow.dts58
-rw-r--r--board/samsung/smdk5250/smdk5250.c178
-rw-r--r--boards.cfg1
-rw-r--r--common/cmd_dtt.c32
-rw-r--r--doc/device-tree-bindings/exynos/tmu.txt44
-rw-r--r--drivers/mmc/sdhci.c8
-rw-r--r--drivers/power/Makefile1
-rw-r--r--drivers/power/exynos-tmu.c319
-rw-r--r--drivers/sound/Makefile1
-rw-r--r--drivers/sound/max98095.c550
-rw-r--r--drivers/sound/max98095.h311
-rw-r--r--drivers/sound/sound.c9
-rw-r--r--include/configs/exynos5250-dt.h6
-rw-r--r--include/configs/snow.h33
-rw-r--r--include/fdtdec.h2
-rw-r--r--include/power/max77686_pmic.h32
-rw-r--r--include/sound.h1
-rw-r--r--include/tmu.h46
-rw-r--r--lib/fdtdec.c2
26 files changed, 1776 insertions, 10 deletions
diff --git a/MAINTAINERS b/MAINTAINERS
index 09430ba4a3..646997327e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -914,6 +914,10 @@ Matt Sealey <matt@genesi-usa.com>
Bo Shen <voice.shen@atmel.com>
at91sam9x5ek ARM926EJS (AT91SAM9G15,G25,G35,X25,X35 SoC)
+Rajeshwari Shinde <rajeshwari.s@samsung.com>
+
+ snow ARM ARMV7 (EXYNOS5250 SoC)
+
Michal Simek <monstr@monstr.eu>
zynq ARM ARMV7 (Zynq SoC)
diff --git a/arch/arm/cpu/armv7/exynos/power.c b/arch/arm/cpu/armv7/exynos/power.c
index d4bce6d4dd..6375a81fd4 100644
--- a/arch/arm/cpu/armv7/exynos/power.c
+++ b/arch/arm/cpu/armv7/exynos/power.c
@@ -95,3 +95,48 @@ void set_dp_phy_ctrl(unsigned int enable)
if (cpu_is_exynos5())
exynos5_dp_phy_control(enable);
}
+
+static void exynos5_set_ps_hold_ctrl(void)
+{
+ struct exynos5_power *power =
+ (struct exynos5_power *)samsung_get_base_power();
+
+ /* Set PS-Hold high */
+ setbits_le32(&power->ps_hold_control,
+ EXYNOS_PS_HOLD_CONTROL_DATA_HIGH);
+}
+
+void set_ps_hold_ctrl(void)
+{
+ if (cpu_is_exynos5())
+ exynos5_set_ps_hold_ctrl();
+}
+
+
+static void exynos5_set_xclkout(void)
+{
+ struct exynos5_power *power =
+ (struct exynos5_power *)samsung_get_base_power();
+
+ /* use xxti for xclk out */
+ clrsetbits_le32(&power->pmu_debug, PMU_DEBUG_CLKOUT_SEL_MASK,
+ PMU_DEBUG_XXTI);
+}
+
+void set_xclkout(void)
+{
+ if (cpu_is_exynos5())
+ exynos5_set_xclkout();
+}
+
+/* Enables hardware tripping to power off the system when TMU fails */
+void set_hw_thermal_trip(void)
+{
+ if (cpu_is_exynos5()) {
+ struct exynos5_power *power =
+ (struct exynos5_power *)samsung_get_base_power();
+
+ /* PS_HOLD_CONTROL register ENABLE_HW_TRIP bit*/
+ setbits_le32(&power->ps_hold_control, POWER_ENABLE_HW_TRIP);
+ }
+}
diff --git a/arch/arm/dts/exynos5250.dtsi b/arch/arm/dts/exynos5250.dtsi
index ed8c8dd606..61d35a83ea 100644
--- a/arch/arm/dts/exynos5250.dtsi
+++ b/arch/arm/dts/exynos5250.dtsi
@@ -151,4 +151,9 @@
};
};
+ tmu@10060000 {
+ compatible = "samsung,exynos-tmu";
+ reg = <0x10060000 0x10000>;
+ };
+
};
diff --git a/arch/arm/include/asm/arch-exynos/power.h b/arch/arm/include/asm/arch-exynos/power.h
index d2fdb59817..3549667d91 100644
--- a/arch/arm/include/asm/arch-exynos/power.h
+++ b/arch/arm/include/asm/arch-exynos/power.h
@@ -857,6 +857,9 @@ void set_mipi_phy_ctrl(unsigned int dev_index, unsigned int enable);
void set_usbhost_phy_ctrl(unsigned int enable);
+/* Enables hardware tripping to power off the system when TMU fails */
+void set_hw_thermal_trip(void);
+
#define POWER_USB_HOST_PHY_CTRL_EN (1 << 0)
#define POWER_USB_HOST_PHY_CTRL_DISABLE (0 << 0)
@@ -864,4 +867,25 @@ void set_dp_phy_ctrl(unsigned int enable);
#define EXYNOS_DP_PHY_ENABLE (1 << 0)
+#define EXYNOS_PS_HOLD_CONTROL_DATA_HIGH (1 << 8)
+#define POWER_ENABLE_HW_TRIP (1UL << 31)
+
+/*
+ * Set ps_hold data driving value high
+ * This enables the machine to stay powered on
+ * after the initial power-on condition goes away
+ * (e.g. power button).
+ */
+void set_ps_hold_ctrl(void);
+
+/* PMU_DEBUG bits [12:8] = 0x1000 selects XXTI clock source */
+#define PMU_DEBUG_XXTI 0x1000
+/* Mask bit[12:8] for xxti clock selection */
+#define PMU_DEBUG_CLKOUT_SEL_MASK 0x1f00
+
+/*
+ * Pmu debug is used for xclkout, enable xclkout with
+ * source as XXTI
+ */
+void set_xclkout(void);
#endif
diff --git a/arch/arm/include/asm/arch-exynos/spl.h b/arch/arm/include/asm/arch-exynos/spl.h
index 306b41d825..46b25a608b 100644
--- a/arch/arm/include/asm/arch-exynos/spl.h
+++ b/arch/arm/include/asm/arch-exynos/spl.h
@@ -78,11 +78,12 @@ struct spl_machine_param {
*/
u32 uboot_size;
enum boot_mode boot_source; /* Boot device */
- enum mem_manuf mem_manuf; /* Memory Manufacturer */
unsigned frequency_mhz; /* Frequency of memory in MHz */
unsigned arm_freq_mhz; /* ARM Frequency in MHz */
u32 serial_base; /* Serial base address */
u32 i2c_base; /* i2c base address */
+ u32 board_rev_gpios; /* Board revision GPIOs */
+ enum mem_manuf mem_manuf; /* Memory Manufacturer */
} __attribute__((__packed__));
#endif
diff --git a/arch/arm/include/asm/arch-exynos/tmu.h b/arch/arm/include/asm/arch-exynos/tmu.h
new file mode 100644
index 0000000000..7e0158efb6
--- /dev/null
+++ b/arch/arm/include/asm/arch-exynos/tmu.h
@@ -0,0 +1,58 @@
+/*
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ * Akshay Saraswat <akshay.s@samsung.com>
+ *
+ * EXYNOS - Thermal Management Unit
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __ASM_ARCH_TMU_H
+#define __ASM_ARCH_TMU_H
+
+struct exynos5_tmu_reg {
+ unsigned triminfo;
+ unsigned rsvd1;
+ unsigned rsvd2;
+ unsigned rsvd3;
+ unsigned rsvd4;
+ unsigned triminfo_control;
+ unsigned rsvd5;
+ unsigned rsvd6;
+ unsigned tmu_control;
+ unsigned rsvd7;
+ unsigned tmu_status;
+ unsigned sampling_internal;
+ unsigned counter_value0;
+ unsigned counter_value1;
+ unsigned rsvd8;
+ unsigned rsvd9;
+ unsigned current_temp;
+ unsigned rsvd10;
+ unsigned rsvd11;
+ unsigned rsvd12;
+ unsigned threshold_temp_rise;
+ unsigned threshold_temp_fall;
+ unsigned rsvd13;
+ unsigned rsvd14;
+ unsigned past_temp3_0;
+ unsigned past_temp7_4;
+ unsigned past_temp11_8;
+ unsigned past_temp15_12;
+ unsigned inten;
+ unsigned intstat;
+ unsigned intclear;
+ unsigned rsvd15;
+ unsigned emul_con;
+};
+#endif /* __ASM_ARCH_TMU_H */
diff --git a/board/samsung/dts/exynos5250-smdk5250.dts b/board/samsung/dts/exynos5250-smdk5250.dts
index cbfab6f97f..1c2d52d622 100644
--- a/board/samsung/dts/exynos5250-smdk5250.dts
+++ b/board/samsung/dts/exynos5250-smdk5250.dts
@@ -66,4 +66,17 @@
compatible = "maxim,max77686_pmic";
};
};
+
+ tmu@10060000 {
+ samsung,min-temp = <25>;
+ samsung,max-temp = <125>;
+ samsung,start-warning = <95>;
+ samsung,start-tripping = <105>;
+ samsung,hw-tripping = <110>;
+ samsung,efuse-min-value = <40>;
+ samsung,efuse-value = <55>;
+ samsung,efuse-max-value = <100>;
+ samsung,slope = <274761730>;
+ samsung,dc-value = <25>;
+ };
};
diff --git a/board/samsung/dts/exynos5250-snow.dts b/board/samsung/dts/exynos5250-snow.dts
new file mode 100644
index 0000000000..8b303bf4e4
--- /dev/null
+++ b/board/samsung/dts/exynos5250-snow.dts
@@ -0,0 +1,58 @@
+/*
+ * SAMSUNG Snow board device tree source
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+/include/ ARCH_CPU_DTS
+
+/ {
+ model = "Google Snow";
+ compatible = "google,snow", "samsung,exynos5250";
+
+ aliases {
+ i2c0 = "/i2c@12c60000";
+ i2c1 = "/i2c@12c70000";
+ i2c2 = "/i2c@12c80000";
+ i2c3 = "/i2c@12c90000";
+ i2c4 = "/i2c@12ca0000";
+ i2c5 = "/i2c@12cb0000";
+ i2c6 = "/i2c@12cc0000";
+ i2c7 = "/i2c@12cd0000";
+ spi0 = "/spi@12d20000";
+ spi1 = "/spi@12d30000";
+ spi2 = "/spi@12d40000";
+ spi3 = "/spi@131a0000";
+ spi4 = "/spi@131b0000";
+ };
+
+ sound@12d60000 {
+ samsung,i2s-epll-clock-frequency = <192000000>;
+ samsung,i2s-sampling-rate = <48000>;
+ samsung,i2s-bits-per-sample = <16>;
+ samsung,i2s-channels = <2>;
+ samsung,i2s-lr-clk-framesize = <256>;
+ samsung,i2s-bit-clk-framesize = <32>;
+ samsung,codec-type = "max98095";
+ };
+
+ i2c@12cd0000 {
+ soundcodec@22 {
+ reg = <0x22>;
+ compatible = "maxim,max98095-codec";
+ };
+ };
+
+ i2c@12c60000 {
+ pmic@9 {
+ reg = <0x9>;
+ compatible = "maxim,max77686_pmic";
+ };
+ };
+};
diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c
index 7a5f132ebb..217c6df301 100644
--- a/board/samsung/smdk5250/smdk5250.c
+++ b/board/samsung/smdk5250/smdk5250.c
@@ -23,6 +23,7 @@
#include <common.h>
#include <fdtdec.h>
#include <asm/io.h>
+#include <errno.h>
#include <i2c.h>
#include <lcd.h>
#include <netdev.h>
@@ -35,9 +36,40 @@
#include <asm/arch/sromc.h>
#include <asm/arch/dp_info.h>
#include <power/pmic.h>
+#include <power/max77686_pmic.h>
+#include <tmu.h>
DECLARE_GLOBAL_DATA_PTR;
+#if defined CONFIG_EXYNOS_TMU
+/*
+ * Boot Time Thermal Analysis for SoC temperature threshold breach
+ */
+static void boot_temp_check(void)
+{
+ int temp;
+
+ switch (tmu_monitor(&temp)) {
+ /* Status TRIPPED ans WARNING means corresponding threshold breach */
+ case TMU_STATUS_TRIPPED:
+ puts("EXYNOS_TMU: TRIPPING! Device power going down ...\n");
+ set_ps_hold_ctrl();
+ hang();
+ break;
+ case TMU_STATUS_WARNING:
+ puts("EXYNOS_TMU: WARNING! Temperature very high\n");
+ break;
+ /*
+ * TMU_STATUS_INIT means something is wrong with temperature sensing
+ * and TMU status was changed back from NORMAL to INIT.
+ */
+ case TMU_STATUS_INIT:
+ default:
+ debug("EXYNOS_TMU: Unknown TMU state\n");
+ }
+}
+#endif
+
#ifdef CONFIG_USB_EHCI_EXYNOS
int board_usb_vbus_init(void)
{
@@ -54,15 +86,39 @@ int board_usb_vbus_init(void)
}
#endif
+#ifdef CONFIG_SOUND_MAX98095
+static void board_enable_audio_codec(void)
+{
+ struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *)
+ samsung_get_base_gpio_part1();
+
+ /* Enable MAX98095 Codec */
+ s5p_gpio_direction_output(&gpio1->x1, 7, 1);
+ s5p_gpio_set_pull(&gpio1->x1, 7, GPIO_PULL_NONE);
+}
+#endif
+
int board_init(void)
{
gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
+
+#if defined CONFIG_EXYNOS_TMU
+ if (tmu_init(gd->fdt_blob) != TMU_STATUS_NORMAL) {
+ debug("%s: Failed to init TMU\n", __func__);
+ return -1;
+ }
+ boot_temp_check();
+#endif
+
#ifdef CONFIG_EXYNOS_SPI
spi_init();
#endif
#ifdef CONFIG_USB_EHCI_EXYNOS
board_usb_vbus_init();
#endif
+#ifdef CONFIG_SOUND_MAX98095
+ board_enable_audio_codec();
+#endif
return 0;
}
@@ -80,12 +136,119 @@ int dram_init(void)
}
#if defined(CONFIG_POWER)
+static int pmic_reg_update(struct pmic *p, int reg, uint regval)
+{
+ u32 val;
+ int ret = 0;
+
+ ret = pmic_reg_read(p, reg, &val);
+ if (ret) {
+ debug("%s: PMIC %d register read failed\n", __func__, reg);
+ return -1;
+ }
+ val |= regval;
+ ret = pmic_reg_write(p, reg, val);
+ if (ret) {
+ debug("%s: PMIC %d register write failed\n", __func__, reg);
+ return -1;
+ }
+ return 0;
+}
+
int power_init_board(void)
{
+ struct pmic *p;
+
+ set_ps_hold_ctrl();
+
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+
if (pmic_init(I2C_PMIC))
return -1;
- else
- return 0;
+
+ p = pmic_get("MAX77686_PMIC");
+ if (!p)
+ return -ENODEV;
+
+ if (pmic_probe(p))
+ return -1;
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_32KHZ, MAX77686_32KHCP_EN))
+ return -1;
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BBAT,
+ MAX77686_BBCHOSTEN | MAX77686_BBCVS_3_5V))
+ return -1;
+
+ /* VDD_MIF */
+ if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK1OUT,
+ MAX77686_BUCK1OUT_1V)) {
+ debug("%s: PMIC %d register write failed\n", __func__,
+ MAX77686_REG_PMIC_BUCK1OUT);
+ return -1;
+ }
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK1CRTL,
+ MAX77686_BUCK1CTRL_EN))
+ return -1;
+
+ /* VDD_ARM */
+ if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK2DVS1,
+ MAX77686_BUCK2DVS1_1_3V)) {
+ debug("%s: PMIC %d register write failed\n", __func__,
+ MAX77686_REG_PMIC_BUCK2DVS1);
+ return -1;
+ }
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK2CTRL1,
+ MAX77686_BUCK2CTRL_ON))
+ return -1;
+
+ /* VDD_INT */
+ if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK3DVS1,
+ MAX77686_BUCK3DVS1_1_0125V)) {
+ debug("%s: PMIC %d register write failed\n", __func__,
+ MAX77686_REG_PMIC_BUCK3DVS1);
+ return -1;
+ }
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK3CTRL,
+ MAX77686_BUCK3CTRL_ON))
+ return -1;
+
+ /* VDD_G3D */
+ if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK4DVS1,
+ MAX77686_BUCK4DVS1_1_2V)) {
+ debug("%s: PMIC %d register write failed\n", __func__,
+ MAX77686_REG_PMIC_BUCK4DVS1);
+ return -1;
+ }
+
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK4CTRL1,
+ MAX77686_BUCK3CTRL_ON))
+ return -1;
+
+ /* VDD_LDO2 */
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO2CTRL1,
+ MAX77686_LD02CTRL1_1_5V | EN_LDO))
+ return -1;
+
+ /* VDD_LDO3 */
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO3CTRL1,
+ MAX77686_LD03CTRL1_1_8V | EN_LDO))
+ return -1;
+
+ /* VDD_LDO5 */
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO5CTRL1,
+ MAX77686_LD05CTRL1_1_8V | EN_LDO))
+ return -1;
+
+ /* VDD_LDO10 */
+ if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO10CTRL1,
+ MAX77686_LD10CTRL1_1_8V | EN_LDO))
+ return -1;
+
+ return 0;
}
#endif
@@ -212,8 +375,17 @@ int board_eth_init(bd_t *bis)
#ifdef CONFIG_DISPLAY_BOARDINFO
int checkboard(void)
{
- printf("\nBoard: SMDK5250\n");
+#ifdef CONFIG_OF_CONTROL
+ const char *board_name;
+ board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL);
+ if (board_name == NULL)
+ printf("\nUnknown Board\n");
+ else
+ printf("\nBoard: %s\n", board_name);
+#else
+ printf("\nBoard: SMDK5250\n");
+#endif
return 0;
}
#endif
diff --git a/boards.cfg b/boards.cfg
index 718a5d6f4e..5fc70be8f5 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -298,6 +298,7 @@ s5p_goni arm armv7 goni samsung
smdkc100 arm armv7 smdkc100 samsung s5pc1xx
origen arm armv7 origen samsung exynos
s5pc210_universal arm armv7 universal_c210 samsung exynos
+snow arm armv7 smdk5250 samsung exynos
smdk5250 arm armv7 smdk5250 samsung exynos
smdkv310 arm armv7 smdkv310 samsung exynos
trats arm armv7 trats samsung exynos
diff --git a/common/cmd_dtt.c b/common/cmd_dtt.c
index cd94423d21..edbd4a83ca 100644
--- a/common/cmd_dtt.c
+++ b/common/cmd_dtt.c
@@ -27,7 +27,9 @@
#include <dtt.h>
#include <i2c.h>
+#include <tmu.h>
+#if defined CONFIG_DTT_SENSORS
static unsigned long sensor_initialized;
static void _initialize_dtt(void)
@@ -59,9 +61,11 @@ void dtt_init(void)
/* switch back to original I2C bus */
I2C_SET_BUS(old_bus);
}
+#endif
-int do_dtt (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
+int dtt_i2c(void)
{
+#if defined CONFIG_DTT_SENSORS
int i;
unsigned char sensors[] = CONFIG_DTT_SENSORS;
int old_bus;
@@ -83,8 +87,34 @@ int do_dtt (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
/* switch back to original I2C bus */
I2C_SET_BUS(old_bus);
+#endif
return 0;
+}
+
+int dtt_tmu(void)
+{
+#if defined CONFIG_TMU_CMD_DTT
+ int cur_temp;
+
+ /* Sense and return latest thermal info */
+ if (tmu_monitor(&cur_temp) == TMU_STATUS_INIT) {
+ puts("TMU is in unknown state, temperature is invalid\n");
+ return -1;
+ }
+ printf("Current temperature: %u degrees Celsius\n", cur_temp);
+#endif
+ return 0;
+}
+
+int do_dtt(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
+{
+ int err = 0;
+
+ err |= dtt_i2c();
+ err |= dtt_tmu();
+
+ return err;
} /* do_dtt() */
/***************************************************/
diff --git a/doc/device-tree-bindings/exynos/tmu.txt b/doc/device-tree-bindings/exynos/tmu.txt
new file mode 100644
index 0000000000..89d3bf05f7
--- /dev/null
+++ b/doc/device-tree-bindings/exynos/tmu.txt
@@ -0,0 +1,44 @@
+Exynos Thermal management Unit
+
+Required properties:
+
+ - compatible : Should be "samsung,exynos-tmu" for TMU
+ - samsung,min-temp : Minimum temperature value (25 degree celsius)
+ - Current temperature of SoC should be more than this value.
+ - samsung,max-temp : Maximum temperature value (125 degree celsius)
+ - Current temperature of SoC should be less than this value.
+ - samsung,start-warning : Temperature at which TMU starts giving warning (degree celsius)
+ - samsung,start-tripping : Temperature at which TMU shuts down the system (degree celsius)
+ - samsung,hw-tripping : Temperature at which hardware tripping should happen
+ in case TMU fails to power off (degree celsius)
+ - samsung,efuse-min-value : SOC efuse min value (Constant 40)
+ - efuse-value should be more than this value.
+ - samsung,efuse-value : SOC actual efuse value (Literal value)
+ - This is the data trimming info.
+ - This value is used to calculate measuring error.
+ - samsung,efuse-max-value : SoC max efuse value (Constant 100)
+ - efuse-value should be less than this value.
+ - samsung,slope : Default value 274761730 (Constant 0x1060_8802).
+ - This is the default value for TMU_CONTROL register.
+ - It sets the gain of amplifier to the positive-tc generator block.
+ - It selects thermal tripping mode and enables thermal tripping.
+ - samsung,dc-value : Measured data calibration value (Constant 25)
+ - Used for tempearture calculation.
+ - This is 25 because temperature measured is always above 25 degrees.
+
+
+Example:
+
+tmu@10060000 {
+ compatible = "samsung,exynos-tmu"
+ samsung,min-temp = <25>;
+ samsung,max-temp = <125>;
+ samsung,start-warning = <95>;
+ samsung,start-tripping = <105>;
+ samsung,hw-tripping = <110>;
+ samsung,efuse-min-value = <40>;
+ samsung,efuse-value = <55>;
+ samsung,efuse-max-value = <100>;
+ samsung,slope = <274761730>;
+ samsung,dc-value = <25>;
+};
diff --git a/drivers/mmc/sdhci.c b/drivers/mmc/sdhci.c
index daca0ea4f7..1eaea04ad1 100644
--- a/drivers/mmc/sdhci.c
+++ b/drivers/mmc/sdhci.c
@@ -412,9 +412,11 @@ int sdhci_init(struct mmc *mmc)
status = sdhci_readl(host, SDHCI_PRESENT_STATE);
}
- /* Eable all state */
- sdhci_writel(host, SDHCI_INT_ALL_MASK, SDHCI_INT_ENABLE);
- sdhci_writel(host, SDHCI_INT_ALL_MASK, SDHCI_SIGNAL_ENABLE);
+ /* Enable only interrupts served by the SD controller */
+ sdhci_writel(host, SDHCI_INT_DATA_MASK | SDHCI_INT_CMD_MASK
+ , SDHCI_INT_ENABLE);
+ /* Mask all sdhci interrupt sources */
+ sdhci_writel(host, 0x0, SDHCI_SIGNAL_ENABLE);
return 0;
}
diff --git a/drivers/power/Makefile b/drivers/power/Makefile
index 8c7190156c..1dac16a9f7 100644
--- a/drivers/power/Makefile
+++ b/drivers/power/Makefile
@@ -25,6 +25,7 @@ include $(TOPDIR)/config.mk
LIB := $(obj)libpower.o
+COBJS-$(CONFIG_EXYNOS_TMU) += exynos-tmu.o
COBJS-$(CONFIG_FTPMU010_POWER) += ftpmu010.o
COBJS-$(CONFIG_TPS6586X_POWER) += tps6586x.o
COBJS-$(CONFIG_TWL4030_POWER) += twl4030.o
diff --git a/drivers/power/exynos-tmu.c b/drivers/power/exynos-tmu.c
new file mode 100644
index 0000000000..d4b3e65a3e
--- /dev/null
+++ b/drivers/power/exynos-tmu.c
@@ -0,0 +1,319 @@
+/*
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ * Akshay Saraswat <akshay.s@samsung.com>
+ *
+ * EXYNOS - Thermal Management Unit
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <fdtdec.h>
+#include <tmu.h>
+#include <asm/arch/tmu.h>
+#include <asm/arch/power.h>
+
+#define TRIMINFO_RELOAD 1
+#define CORE_EN 1
+#define THERM_TRIP_EN (1 << 12)
+
+#define INTEN_RISE0 1
+#define INTEN_RISE1 (1 << 4)
+#define INTEN_RISE2 (1 << 8)
+#define INTEN_FALL0 (1 << 16)
+#define INTEN_FALL1 (1 << 20)
+#define INTEN_FALL2 (1 << 24)
+
+#define TRIM_INFO_MASK 0xff
+
+#define INTCLEAR_RISE0 1
+#define INTCLEAR_RISE1 (1 << 4)
+#define INTCLEAR_RISE2 (1 << 8)
+#define INTCLEAR_FALL0 (1 << 16)
+#define INTCLEAR_FALL1 (1 << 20)
+#define INTCLEAR_FALL2 (1 << 24)
+#define INTCLEARALL (INTCLEAR_RISE0 | INTCLEAR_RISE1 | \
+ INTCLEAR_RISE2 | INTCLEAR_FALL0 | \
+ INTCLEAR_FALL1 | INTCLEAR_FALL2)
+
+/* Tmeperature threshold values for various thermal events */
+struct temperature_params {
+ /* minimum value in temperature code range */
+ unsigned int min_val;
+ /* maximum value in temperature code range */
+ unsigned int max_val;
+ /* temperature threshold to start warning */
+ unsigned int start_warning;
+ /* temperature threshold CPU tripping */
+ unsigned int start_tripping;
+ /* temperature threshold for HW tripping */
+ unsigned int hardware_tripping;
+};
+
+/* Pre-defined values and thresholds for calibration of current temperature */
+struct tmu_data {
+ /* pre-defined temperature thresholds */
+ struct temperature_params ts;
+ /* pre-defined efuse range minimum value */
+ unsigned int efuse_min_value;
+ /* pre-defined efuse value for temperature calibration */
+ unsigned int efuse_value;
+ /* pre-defined efuse range maximum value */
+ unsigned int efuse_max_value;
+ /* current temperature sensing slope */
+ unsigned int slope;
+};
+
+/* TMU device specific details and status */
+struct tmu_info {
+ /* base Address for the TMU */
+ unsigned tmu_base;
+ /* pre-defined values for calibration and thresholds */
+ struct tmu_data data;
+ /* value required for triminfo_25 calibration */
+ unsigned int te1;
+ /* value required for triminfo_85 calibration */
+ unsigned int te2;
+ /* Value for measured data calibration */
+ int dc_value;
+ /* enum value indicating status of the TMU */
+ int tmu_state;
+};
+
+/* Global struct tmu_info variable to store init values */
+static struct tmu_info gbl_info;
+
+/*
+ * Get current temperature code from register,
+ * then calculate and calibrate it's value
+ * in degree celsius.
+ *
+ * @return current temperature of the chip as sensed by TMU
+ */
+static int get_cur_temp(struct tmu_info *info)
+{
+ int cur_temp;
+ struct exynos5_tmu_reg *reg = (struct exynos5_tmu_reg *)info->tmu_base;
+
+ /*
+ * Temperature code range between min 25 and max 125.
+ * May run more than once for first call as initial sensing
+ * has not yet happened.
+ */
+ do {
+ cur_temp = readl(&reg->current_temp) & 0xff;
+ } while (cur_temp == 0 && info->tmu_state == TMU_STATUS_NORMAL);
+
+ /* Calibrate current temperature */
+ cur_temp = cur_temp - info->te1 + info->dc_value;
+
+ return cur_temp;
+}
+
+/*
+ * Monitors status of the TMU device and exynos temperature
+ *
+ * @param temp pointer to the current temperature value
+ * @return enum tmu_status_t value, code indicating event to execute
+ */
+enum tmu_status_t tmu_monitor(int *temp)
+{
+ int cur_temp;
+ struct tmu_data *data = &gbl_info.data;
+
+ if (gbl_info.tmu_state == TMU_STATUS_INIT)
+ return TMU_STATUS_INIT;
+
+ /* Read current temperature of the SOC */
+ cur_temp = get_cur_temp(&gbl_info);
+ *temp = cur_temp;
+
+ /* Temperature code lies between min 25 and max 125 */
+ if (cur_temp >= data->ts.start_tripping &&
+ cur_temp <= data->ts.max_val) {
+ return TMU_STATUS_TRIPPED;
+ } else if (cur_temp >= data->ts.start_warning) {
+ return TMU_STATUS_WARNING;
+ } else if (cur_temp < data->ts.start_warning &&
+ cur_temp >= data->ts.min_val) {
+ return TMU_STATUS_NORMAL;
+ } else {
+ /* Temperature code does not lie between min 25 and max 125 */
+ gbl_info.tmu_state = TMU_STATUS_INIT;
+ debug("EXYNOS_TMU: Thermal reading failed\n");
+ return TMU_STATUS_INIT;
+ }
+}
+
+/*
+ * Get TMU specific pre-defined values from FDT
+ *
+ * @param info pointer to the tmu_info struct
+ * @param blob FDT blob
+ * @return int value, 0 for success
+ */
+static int get_tmu_fdt_values(struct tmu_info *info, const void *blob)
+{
+#ifdef CONFIG_OF_CONTROL
+ int node;
+ int error = 0;
+
+ /* Get the node from FDT for TMU */
+ node = fdtdec_next_compatible(blob, 0,
+ COMPAT_SAMSUNG_EXYNOS_TMU);
+ if (node < 0) {
+ debug("EXYNOS_TMU: No node for tmu in device tree\n");
+ return -1;
+ }
+
+ /*
+ * Get the pre-defined TMU specific values from FDT.
+ * All of these are expected to be correct otherwise
+ * miscalculation of register values in tmu_setup_parameters
+ * may result in misleading current temperature.
+ */
+ info->tmu_base = fdtdec_get_addr(blob, node, "reg");
+ if (info->tmu_base == FDT_ADDR_T_NONE) {
+ debug("%s: Missing tmu-base\n", __func__);
+ return -1;
+ }
+ info->data.ts.min_val = fdtdec_get_int(blob,
+ node, "samsung,min-temp", -1);
+ error |= info->data.ts.min_val;
+ info->data.ts.max_val = fdtdec_get_int(blob,
+ node, "samsung,max-temp", -1);
+ error |= info->data.ts.max_val;
+ info->data.ts.start_warning = fdtdec_get_int(blob,
+ node, "samsung,start-warning", -1);
+ error |= info->data.ts.start_warning;
+ info->data.ts.start_tripping = fdtdec_get_int(blob,
+ node, "samsung,start-tripping", -1);
+ error |= info->data.ts.start_tripping;
+ info->data.ts.hardware_tripping = fdtdec_get_int(blob,
+ node, "samsung,hw-tripping", -1);
+ error |= info->data.ts.hardware_tripping;
+ info->data.efuse_min_value = fdtdec_get_int(blob,
+ node, "samsung,efuse-min-value", -1);
+ error |= info->data.efuse_min_value;
+ info->data.efuse_value = fdtdec_get_int(blob,
+ node, "samsung,efuse-value", -1);
+ error |= info->data.efuse_value;
+ info->data.efuse_max_value = fdtdec_get_int(blob,
+ node, "samsung,efuse-max-value", -1);
+ error |= info->data.efuse_max_value;
+ info->data.slope = fdtdec_get_int(blob,
+ node, "samsung,slope", -1);
+ error |= info->data.slope;
+ info->dc_value = fdtdec_get_int(blob,
+ node, "samsung,dc-value", -1);
+ error |= info->dc_value;
+
+ if (error == -1) {
+ debug("fail to get tmu node properties\n");
+ return -1;
+ }
+#endif
+
+ return 0;
+}
+
+/*
+ * Calibrate and calculate threshold values and
+ * enable interrupt levels
+ *
+ * @param info pointer to the tmu_info struct
+ */
+static void tmu_setup_parameters(struct tmu_info *info)
+{
+ unsigned int te_code, con;
+ unsigned int warning_code, trip_code, hwtrip_code;
+ unsigned int cooling_temp;
+ unsigned int rising_value;
+ struct tmu_data *data = &info->data;
+ struct exynos5_tmu_reg *reg = (struct exynos5_tmu_reg *)info->tmu_base;
+
+ /* Must reload for reading efuse value from triminfo register */
+ writel(TRIMINFO_RELOAD, &reg->triminfo_control);
+
+ /* Get the compensation parameter */
+ te_code = readl(&reg->triminfo);
+ info->te1 = te_code & TRIM_INFO_MASK;
+ info->te2 = ((te_code >> 8) & TRIM_INFO_MASK);
+
+ if ((data->efuse_min_value > info->te1) ||
+ (info->te1 > data->efuse_max_value)
+ || (info->te2 != 0))
+ info->te1 = data->efuse_value;
+
+ /* Get RISING & FALLING Threshold value */
+ warning_code = data->ts.start_warning
+ + info->te1 - info->dc_value;
+ trip_code = data->ts.start_tripping
+ + info->te1 - info->dc_value;
+ hwtrip_code = data->ts.hardware_tripping
+ + info->te1 - info->dc_value;
+
+ cooling_temp = 0;
+
+ rising_value = ((warning_code << 8) |
+ (trip_code << 16) |
+ (hwtrip_code << 24));
+
+ /* Set interrupt level */
+ writel(rising_value, &reg->threshold_temp_rise);
+ writel(cooling_temp, &reg->threshold_temp_fall);
+
+ /*
+ * Init TMU control tuning parameters
+ * [28:24] VREF - Voltage reference
+ * [15:13] THERM_TRIP_MODE - Tripping mode
+ * [12] THERM_TRIP_EN - Thermal tripping enable
+ * [11:8] BUF_SLOPE_SEL - Gain of amplifier
+ * [6] THERM_TRIP_BY_TQ_EN - Tripping by TQ pin
+ */
+ writel(data->slope, &reg->tmu_control);
+
+ writel(INTCLEARALL, &reg->intclear);
+
+ /* TMU core enable */
+ con = readl(&reg->tmu_control);
+ con |= THERM_TRIP_EN | CORE_EN;
+
+ writel(con, &reg->tmu_control);
+
+ /* Enable HW thermal trip */
+ set_hw_thermal_trip();
+
+ /* LEV1 LEV2 interrupt enable */
+ writel(INTEN_RISE1 | INTEN_RISE2, &reg->inten);
+}
+
+/*
+ * Initialize TMU device
+ *
+ * @param blob FDT blob
+ * @return int value, 0 for success
+ */
+int tmu_init(const void *blob)
+{
+ gbl_info.tmu_state = TMU_STATUS_INIT;
+ if (get_tmu_fdt_values(&gbl_info, blob) < 0)
+ goto ret;
+
+ tmu_setup_parameters(&gbl_info);
+ gbl_info.tmu_state = TMU_STATUS_NORMAL;
+ret:
+
+ return gbl_info.tmu_state;
+}
diff --git a/drivers/sound/Makefile b/drivers/sound/Makefile
index 8fdffb10ef..1987ca1a05 100644
--- a/drivers/sound/Makefile
+++ b/drivers/sound/Makefile
@@ -28,6 +28,7 @@ LIB := $(obj)libsound.o
COBJS-$(CONFIG_SOUND) += sound.o
COBJS-$(CONFIG_I2S) += samsung-i2s.o
COBJS-$(CONFIG_SOUND_WM8994) += wm8994.o
+COBJS-$(CONFIG_SOUND_MAX98095) += max98095.o
COBJS := $(COBJS-y)
SRCS := $(COBJS:.o=.c)
diff --git a/drivers/sound/max98095.c b/drivers/sound/max98095.c
new file mode 100644
index 0000000000..d69db58dcd
--- /dev/null
+++ b/drivers/sound/max98095.c
@@ -0,0 +1,550 @@
+/*
+ * max98095.c -- MAX98095 ALSA SoC Audio driver
+ *
+ * Copyright 2011 Maxim Integrated Products
+ *
+ * Modified for uboot by R. Chandrasekar (rcsekar@samsung.com)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <asm/arch/clk.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/power.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <common.h>
+#include <div64.h>
+#include <fdtdec.h>
+#include <i2c.h>
+#include <sound.h>
+#include "i2s.h"
+#include "max98095.h"
+
+enum max98095_type {
+ MAX98095,
+};
+
+struct max98095_priv {
+ enum max98095_type devtype;
+ unsigned int sysclk;
+ unsigned int rate;
+ unsigned int fmt;
+};
+
+static struct sound_codec_info g_codec_info;
+struct max98095_priv g_max98095_info;
+unsigned int g_max98095_i2c_dev_addr;
+
+/* Index 0 is reserved. */
+int rate_table[] = {0, 8000, 11025, 16000, 22050, 24000, 32000, 44100, 48000,
+ 88200, 96000};
+
+/*
+ * Writes value to a device register through i2c
+ *
+ * @param reg reg number to be write
+ * @param data data to be writen to the above registor
+ *
+ * @return int value 1 for change, 0 for no change or negative error code.
+ */
+static int max98095_i2c_write(unsigned int reg, unsigned char data)
+{
+ debug("%s: Write Addr : 0x%02X, Data : 0x%02X\n",
+ __func__, reg, data);
+ return i2c_write(g_max98095_i2c_dev_addr, reg, 1, &data, 1);
+}
+
+/*
+ * Read a value from a device register through i2c
+ *
+ * @param reg reg number to be read
+ * @param data address of read data to be stored
+ *
+ * @return int value 0 for success, -1 in case of error.
+ */
+static unsigned int max98095_i2c_read(unsigned int reg, unsigned char *data)
+{
+ int ret;
+
+ ret = i2c_read(g_max98095_i2c_dev_addr, reg, 1, data, 1);
+ if (ret != 0) {
+ debug("%s: Error while reading register %#04x\n",
+ __func__, reg);
+ return -1;
+ }
+
+ return 0;
+}
+
+/*
+ * update device register bits through i2c
+ *
+ * @param reg codec register
+ * @param mask register mask
+ * @param value new value
+ *
+ * @return int value 0 for success, non-zero error code.
+ */
+static int max98095_update_bits(unsigned int reg, unsigned char mask,
+ unsigned char value)
+{
+ int change, ret = 0;
+ unsigned char old, new;
+
+ if (max98095_i2c_read(reg, &old) != 0)
+ return -1;
+ new = (old & ~mask) | (value & mask);
+ change = (old != new) ? 1 : 0;
+ if (change)
+ ret = max98095_i2c_write(reg, new);
+ if (ret < 0)
+ return ret;
+
+ return change;
+}
+
+/*
+ * codec mclk clock divider coefficients based on sampling rate
+ *
+ * @param rate sampling rate
+ * @param value address of indexvalue to be stored
+ *
+ * @return 0 for success or negative error code.
+ */
+static int rate_value(int rate, u8 *value)
+{
+ int i;
+
+ for (i = 1; i < ARRAY_SIZE(rate_table); i++) {
+ if (rate_table[i] >= rate) {
+ *value = i;
+ return 0;
+ }
+ }
+ *value = 1;
+
+ return -1;
+}
+
+/*
+ * Sets hw params for max98095
+ *
+ * @param max98095 max98095 information pointer
+ * @param rate Sampling rate
+ * @param bits_per_sample Bits per sample
+ *
+ * @return -1 for error and 0 Success.
+ */
+static int max98095_hw_params(struct max98095_priv *max98095,
+ unsigned int rate, unsigned int bits_per_sample)
+{
+ u8 regval;
+ int error;
+
+ switch (bits_per_sample) {
+ case 16:
+ error = max98095_update_bits(M98095_034_DAI2_FORMAT,
+ M98095_DAI_WS, 0);
+ break;
+ case 24:
+ error = max98095_update_bits(M98095_034_DAI2_FORMAT,
+ M98095_DAI_WS, M98095_DAI_WS);
+ break;
+ default:
+ debug("%s: Illegal bits per sample %d.\n",
+ __func__, bits_per_sample);
+ return -1;
+ }
+
+ if (rate_value(rate, &regval)) {
+ debug("%s: Failed to set sample rate to %d.\n",
+ __func__, rate);
+ return -1;
+ }
+ max98095->rate = rate;
+
+ error |= max98095_update_bits(M98095_031_DAI2_CLKMODE,
+ M98095_CLKMODE_MASK, regval);
+
+ /* Update sample rate mode */
+ if (rate < 50000)
+ error |= max98095_update_bits(M98095_038_DAI2_FILTERS,
+ M98095_DAI_DHF, 0);
+ else
+ error |= max98095_update_bits(M98095_038_DAI2_FILTERS,
+ M98095_DAI_DHF, M98095_DAI_DHF);
+
+ if (error < 0) {
+ debug("%s: Error setting hardware params.\n", __func__);
+ return -1;
+ }
+
+ return 0;
+}
+
+/*
+ * Configures Audio interface system clock for the given frequency
+ *
+ * @param max98095 max98095 information
+ * @param freq Sampling frequency in Hz
+ *
+ * @return -1 for error and 0 success.
+ */
+static int max98095_set_sysclk(struct max98095_priv *max98095,
+ unsigned int freq)
+{
+ int error = 0;
+
+ /* Requested clock frequency is already setup */
+ if (freq == max98095->sysclk)
+ return 0;
+
+ /* Setup clocks for slave mode, and using the PLL
+ * PSCLK = 0x01 (when master clk is 10MHz to 20MHz)
+ * 0x02 (when master clk is 20MHz to 40MHz)..
+ * 0x03 (when master clk is 40MHz to 60MHz)..
+ */
+ if ((freq >= 10000000) && (freq < 20000000)) {
+ error = max98095_i2c_write(M98095_026_SYS_CLK, 0x10);
+ } else if ((freq >= 20000000) && (freq < 40000000)) {
+ error = max98095_i2c_write(M98095_026_SYS_CLK, 0x20);
+ } else if ((freq >= 40000000) && (freq < 60000000)) {
+ error = max98095_i2c_write(M98095_026_SYS_CLK, 0x30);
+ } else {
+ debug("%s: Invalid master clock frequency\n", __func__);
+ return -1;
+ }
+
+ debug("%s: Clock at %uHz\n", __func__, freq);
+
+ if (error < 0)
+ return -1;
+
+ max98095->sysclk = freq;
+ return 0;
+}
+
+/*
+ * Sets Max98095 I2S format
+ *
+ * @param max98095 max98095 information
+ * @param fmt i2S format - supports a subset of the options defined
+ * in i2s.h.
+ *
+ * @return -1 for error and 0 Success.
+ */
+static int max98095_set_fmt(struct max98095_priv *max98095, int fmt)
+{
+ u8 regval = 0;
+ int error = 0;
+
+ if (fmt == max98095->fmt)
+ return 0;
+
+ max98095->fmt = fmt;
+
+ switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
+ case SND_SOC_DAIFMT_CBS_CFS:
+ /* Slave mode PLL */
+ error |= max98095_i2c_write(M98095_032_DAI2_CLKCFG_HI,
+ 0x80);
+ error |= max98095_i2c_write(M98095_033_DAI2_CLKCFG_LO,
+ 0x00);
+ break;
+ case SND_SOC_DAIFMT_CBM_CFM:
+ /* Set to master mode */
+ regval |= M98095_DAI_MAS;
+ break;
+ case SND_SOC_DAIFMT_CBS_CFM:
+ case SND_SOC_DAIFMT_CBM_CFS:
+ default:
+ debug("%s: Clock mode unsupported\n", __func__);
+ return -1;
+ }
+
+ switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
+ case SND_SOC_DAIFMT_I2S:
+ regval |= M98095_DAI_DLY;
+ break;
+ case SND_SOC_DAIFMT_LEFT_J:
+ break;
+ default:
+ debug("%s: Unrecognized format.\n", __func__);
+ return -1;
+ }
+
+ switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+ case SND_SOC_DAIFMT_NB_NF:
+ break;
+ case SND_SOC_DAIFMT_NB_IF:
+ regval |= M98095_DAI_WCI;
+ break;
+ case SND_SOC_DAIFMT_IB_NF:
+ regval |= M98095_DAI_BCI;
+ break;
+ case SND_SOC_DAIFMT_IB_IF:
+ regval |= M98095_DAI_BCI | M98095_DAI_WCI;
+ break;
+ default:
+ debug("%s: Unrecognized inversion settings.\n", __func__);
+ return -1;
+ }
+
+ error |= max98095_update_bits(M98095_034_DAI2_FORMAT,
+ M98095_DAI_MAS | M98095_DAI_DLY | M98095_DAI_BCI |
+ M98095_DAI_WCI, regval);
+
+ error |= max98095_i2c_write(M98095_035_DAI2_CLOCK,
+ M98095_DAI_BSEL64);
+
+ if (error < 0) {
+ debug("%s: Error setting i2s format.\n", __func__);
+ return -1;
+ }
+
+ return 0;
+}
+
+/*
+ * resets the audio codec
+ *
+ * @return -1 for error and 0 success.
+ */
+static int max98095_reset(void)
+{
+ int i, ret;
+
+ /*
+ * Gracefully reset the DSP core and the codec hardware in a proper
+ * sequence.
+ */
+ ret = max98095_i2c_write(M98095_00F_HOST_CFG, 0);
+ if (ret != 0) {
+ debug("%s: Failed to reset DSP: %d\n", __func__, ret);
+ return ret;
+ }
+
+ ret = max98095_i2c_write(M98095_097_PWR_SYS, 0);
+ if (ret != 0) {
+ debug("%s: Failed to reset codec: %d\n", __func__, ret);
+ return ret;
+ }
+
+ /*
+ * Reset to hardware default for registers, as there is not a soft
+ * reset hardware control register.
+ */
+ for (i = M98095_010_HOST_INT_CFG; i < M98095_REG_MAX_CACHED; i++) {
+ ret = max98095_i2c_write(i, 0);
+ if (ret < 0) {
+ debug("%s: Failed to reset: %d\n", __func__, ret);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+/*
+ * Intialise max98095 codec device
+ *
+ * @param max98095 max98095 information
+ *
+ * @returns -1 for error and 0 Success.
+ */
+static int max98095_device_init(struct max98095_priv *max98095)
+{
+ unsigned char id;
+ int error = 0;
+
+ /* reset the codec, the DSP core, and disable all interrupts */
+ error = max98095_reset();
+ if (error != 0) {
+ debug("Reset\n");
+ return error;
+ }
+
+ /* initialize private data */
+ max98095->sysclk = -1U;
+ max98095->rate = -1U;
+ max98095->fmt = -1U;
+
+ error = max98095_i2c_read(M98095_0FF_REV_ID, &id);
+ if (error < 0) {
+ debug("%s: Failure reading hardware revision: %d\n",
+ __func__, id);
+ goto err_access;
+ }
+ debug("%s: Hardware revision: %c\n", __func__, (id - 0x40) + 'A');
+
+ error |= max98095_i2c_write(M98095_097_PWR_SYS, M98095_PWRSV);
+
+ /*
+ * initialize registers to hardware default configuring audio
+ * interface2 to DAC
+ */
+ error |= max98095_i2c_write(M98095_048_MIX_DAC_LR,
+ M98095_DAI2M_TO_DACL|M98095_DAI2M_TO_DACR);
+
+ error |= max98095_i2c_write(M98095_092_PWR_EN_OUT,
+ M98095_SPK_SPREADSPECTRUM);
+ error |= max98095_i2c_write(M98095_045_CFG_DSP, M98095_DSPNORMAL);
+ error |= max98095_i2c_write(M98095_04E_CFG_HP, M98095_HPNORMAL);
+
+ error |= max98095_i2c_write(M98095_02C_DAI1_IOCFG,
+ M98095_S1NORMAL|M98095_SDATA);
+
+ error |= max98095_i2c_write(M98095_036_DAI2_IOCFG,
+ M98095_S2NORMAL|M98095_SDATA);
+
+ error |= max98095_i2c_write(M98095_040_DAI3_IOCFG,
+ M98095_S3NORMAL|M98095_SDATA);
+
+ /* take the codec out of the shut down */
+ error |= max98095_update_bits(M98095_097_PWR_SYS, M98095_SHDNRUN,
+ M98095_SHDNRUN);
+ /* route DACL and DACR output to HO and Spekers */
+ error |= max98095_i2c_write(M98095_050_MIX_SPK_LEFT, 0x01); /* DACL */
+ error |= max98095_i2c_write(M98095_051_MIX_SPK_RIGHT, 0x01);/* DACR */
+ error |= max98095_i2c_write(M98095_04C_MIX_HP_LEFT, 0x01); /* DACL */
+ error |= max98095_i2c_write(M98095_04D_MIX_HP_RIGHT, 0x01); /* DACR */
+
+ /* power Enable */
+ error |= max98095_i2c_write(M98095_091_PWR_EN_OUT, 0xF3);
+
+ /* set Volume */
+ error |= max98095_i2c_write(M98095_064_LVL_HP_L, 15);
+ error |= max98095_i2c_write(M98095_065_LVL_HP_R, 15);
+ error |= max98095_i2c_write(M98095_067_LVL_SPK_L, 16);
+ error |= max98095_i2c_write(M98095_068_LVL_SPK_R, 16);
+
+ /* Enable DAIs */
+ error |= max98095_i2c_write(M98095_093_BIAS_CTRL, 0x30);
+ error |= max98095_i2c_write(M98095_096_PWR_DAC_CK, 0x07);
+
+err_access:
+ if (error < 0)
+ return -1;
+
+ return 0;
+}
+
+static int max98095_do_init(struct sound_codec_info *pcodec_info,
+ int sampling_rate, int mclk_freq,
+ int bits_per_sample)
+{
+ int ret = 0;
+
+ /* Enable codec clock */
+ set_xclkout();
+
+ /* shift the device address by 1 for 7 bit addressing */
+ g_max98095_i2c_dev_addr = pcodec_info->i2c_dev_addr >> 1;
+
+ if (pcodec_info->codec_type == CODEC_MAX_98095)
+ g_max98095_info.devtype = MAX98095;
+ else {
+ debug("%s: Codec id [%d] not defined\n", __func__,
+ pcodec_info->codec_type);
+ return -1;
+ }
+
+ ret = max98095_device_init(&g_max98095_info);
+ if (ret < 0) {
+ debug("%s: max98095 codec chip init failed\n", __func__);
+ return ret;
+ }
+
+ ret = max98095_set_sysclk(&g_max98095_info, mclk_freq);
+ if (ret < 0) {
+ debug("%s: max98095 codec set sys clock failed\n", __func__);
+ return ret;
+ }
+
+ ret = max98095_hw_params(&g_max98095_info, sampling_rate,
+ bits_per_sample);
+
+ if (ret == 0) {
+ ret = max98095_set_fmt(&g_max98095_info,
+ SND_SOC_DAIFMT_I2S |
+ SND_SOC_DAIFMT_NB_NF |
+ SND_SOC_DAIFMT_CBS_CFS);
+ }
+
+ return ret;
+}
+
+static int get_max98095_codec_values(struct sound_codec_info *pcodec_info,
+ const void *blob)
+{
+ int error = 0;
+#ifdef CONFIG_OF_CONTROL
+ enum fdt_compat_id compat;
+ int node;
+ int parent;
+
+ /* Get the node from FDT for codec */
+ node = fdtdec_next_compatible(blob, 0, COMPAT_MAXIM_98095_CODEC);
+ if (node <= 0) {
+ debug("EXYNOS_SOUND: No node for codec in device tree\n");
+ debug("node = %d\n", node);
+ return -1;
+ }
+
+ parent = fdt_parent_offset(blob, node);
+ if (parent < 0) {
+ debug("%s: Cannot find node parent\n", __func__);
+ return -1;
+ }
+
+ compat = fdtdec_lookup(blob, parent);
+ switch (compat) {
+ case COMPAT_SAMSUNG_S3C2440_I2C:
+ pcodec_info->i2c_bus = i2c_get_bus_num_fdt(parent);
+ error |= pcodec_info->i2c_bus;
+ debug("i2c bus = %d\n", pcodec_info->i2c_bus);
+ pcodec_info->i2c_dev_addr = fdtdec_get_int(blob, node,
+ "reg", 0);
+ error |= pcodec_info->i2c_dev_addr;
+ debug("i2c dev addr = %x\n", pcodec_info->i2c_dev_addr);
+ break;
+ default:
+ debug("%s: Unknown compat id %d\n", __func__, compat);
+ return -1;
+ }
+#else
+ pcodec_info->i2c_bus = AUDIO_I2C_BUS;
+ pcodec_info->i2c_dev_addr = AUDIO_I2C_REG;
+ debug("i2c dev addr = %d\n", pcodec_info->i2c_dev_addr);
+#endif
+ pcodec_info->codec_type = CODEC_MAX_98095;
+ if (error == -1) {
+ debug("fail to get max98095 codec node properties\n");
+ return -1;
+ }
+
+ return 0;
+}
+
+/* max98095 Device Initialisation */
+int max98095_init(const void *blob, int sampling_rate, int mclk_freq,
+ int bits_per_sample)
+{
+ int ret;
+ int old_bus = i2c_get_bus_num();
+ struct sound_codec_info *pcodec_info = &g_codec_info;
+
+ if (get_max98095_codec_values(pcodec_info, blob) < 0) {
+ debug("FDT Codec values failed\n");
+ return -1;
+ }
+
+ i2c_set_bus_num(pcodec_info->i2c_bus);
+ ret = max98095_do_init(pcodec_info, sampling_rate, mclk_freq,
+ bits_per_sample);
+ i2c_set_bus_num(old_bus);
+
+ return ret;
+}
diff --git a/drivers/sound/max98095.h b/drivers/sound/max98095.h
new file mode 100644
index 0000000000..ae5eb14dbb
--- /dev/null
+++ b/drivers/sound/max98095.h
@@ -0,0 +1,311 @@
+/*
+ * max98095.h -- MAX98095 ALSA SoC Audio driver
+ *
+ * Copyright 2011 Maxim Integrated Products
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _MAX98095_H
+#define _MAX98095_H
+
+/*
+ * MAX98095 Registers Definition
+ */
+
+#define M98095_000_HOST_DATA 0x00
+#define M98095_001_HOST_INT_STS 0x01
+#define M98095_002_HOST_RSP_STS 0x02
+#define M98095_003_HOST_CMD_STS 0x03
+#define M98095_004_CODEC_STS 0x04
+#define M98095_005_DAI1_ALC_STS 0x05
+#define M98095_006_DAI2_ALC_STS 0x06
+#define M98095_007_JACK_AUTO_STS 0x07
+#define M98095_008_JACK_MANUAL_STS 0x08
+#define M98095_009_JACK_VBAT_STS 0x09
+#define M98095_00A_ACC_ADC_STS 0x0A
+#define M98095_00B_MIC_NG_AGC_STS 0x0B
+#define M98095_00C_SPK_L_VOLT_STS 0x0C
+#define M98095_00D_SPK_R_VOLT_STS 0x0D
+#define M98095_00E_TEMP_SENSOR_STS 0x0E
+#define M98095_00F_HOST_CFG 0x0F
+#define M98095_010_HOST_INT_CFG 0x10
+#define M98095_011_HOST_INT_EN 0x11
+#define M98095_012_CODEC_INT_EN 0x12
+#define M98095_013_JACK_INT_EN 0x13
+#define M98095_014_JACK_INT_EN 0x14
+#define M98095_015_DEC 0x15
+#define M98095_016_RESERVED 0x16
+#define M98095_017_RESERVED 0x17
+#define M98095_018_KEYCODE3 0x18
+#define M98095_019_KEYCODE2 0x19
+#define M98095_01A_KEYCODE1 0x1A
+#define M98095_01B_KEYCODE0 0x1B
+#define M98095_01C_OEMCODE1 0x1C
+#define M98095_01D_OEMCODE0 0x1D
+#define M98095_01E_XCFG1 0x1E
+#define M98095_01F_XCFG2 0x1F
+#define M98095_020_XCFG3 0x20
+#define M98095_021_XCFG4 0x21
+#define M98095_022_XCFG5 0x22
+#define M98095_023_XCFG6 0x23
+#define M98095_024_XGPIO 0x24
+#define M98095_025_XCLKCFG 0x25
+#define M98095_026_SYS_CLK 0x26
+#define M98095_027_DAI1_CLKMODE 0x27
+#define M98095_028_DAI1_CLKCFG_HI 0x28
+#define M98095_029_DAI1_CLKCFG_LO 0x29
+#define M98095_02A_DAI1_FORMAT 0x2A
+#define M98095_02B_DAI1_CLOCK 0x2B
+#define M98095_02C_DAI1_IOCFG 0x2C
+#define M98095_02D_DAI1_TDM 0x2D
+#define M98095_02E_DAI1_FILTERS 0x2E
+#define M98095_02F_DAI1_LVL1 0x2F
+#define M98095_030_DAI1_LVL2 0x30
+#define M98095_031_DAI2_CLKMODE 0x31
+#define M98095_032_DAI2_CLKCFG_HI 0x32
+#define M98095_033_DAI2_CLKCFG_LO 0x33
+#define M98095_034_DAI2_FORMAT 0x34
+#define M98095_035_DAI2_CLOCK 0x35
+#define M98095_036_DAI2_IOCFG 0x36
+#define M98095_037_DAI2_TDM 0x37
+#define M98095_038_DAI2_FILTERS 0x38
+#define M98095_039_DAI2_LVL1 0x39
+#define M98095_03A_DAI2_LVL2 0x3A
+#define M98095_03B_DAI3_CLKMODE 0x3B
+#define M98095_03C_DAI3_CLKCFG_HI 0x3C
+#define M98095_03D_DAI3_CLKCFG_LO 0x3D
+#define M98095_03E_DAI3_FORMAT 0x3E
+#define M98095_03F_DAI3_CLOCK 0x3F
+#define M98095_040_DAI3_IOCFG 0x40
+#define M98095_041_DAI3_TDM 0x41
+#define M98095_042_DAI3_FILTERS 0x42
+#define M98095_043_DAI3_LVL1 0x43
+#define M98095_044_DAI3_LVL2 0x44
+#define M98095_045_CFG_DSP 0x45
+#define M98095_046_DAC_CTRL1 0x46
+#define M98095_047_DAC_CTRL2 0x47
+#define M98095_048_MIX_DAC_LR 0x48
+#define M98095_049_MIX_DAC_M 0x49
+#define M98095_04A_MIX_ADC_LEFT 0x4A
+#define M98095_04B_MIX_ADC_RIGHT 0x4B
+#define M98095_04C_MIX_HP_LEFT 0x4C
+#define M98095_04D_MIX_HP_RIGHT 0x4D
+#define M98095_04E_CFG_HP 0x4E
+#define M98095_04F_MIX_RCV 0x4F
+#define M98095_050_MIX_SPK_LEFT 0x50
+#define M98095_051_MIX_SPK_RIGHT 0x51
+#define M98095_052_MIX_SPK_CFG 0x52
+#define M98095_053_MIX_LINEOUT1 0x53
+#define M98095_054_MIX_LINEOUT2 0x54
+#define M98095_055_MIX_LINEOUT_CFG 0x55
+#define M98095_056_LVL_SIDETONE_DAI12 0x56
+#define M98095_057_LVL_SIDETONE_DAI3 0x57
+#define M98095_058_LVL_DAI1_PLAY 0x58
+#define M98095_059_LVL_DAI1_EQ 0x59
+#define M98095_05A_LVL_DAI2_PLAY 0x5A
+#define M98095_05B_LVL_DAI2_EQ 0x5B
+#define M98095_05C_LVL_DAI3_PLAY 0x5C
+#define M98095_05D_LVL_ADC_L 0x5D
+#define M98095_05E_LVL_ADC_R 0x5E
+#define M98095_05F_LVL_MIC1 0x5F
+#define M98095_060_LVL_MIC2 0x60
+#define M98095_061_LVL_LINEIN 0x61
+#define M98095_062_LVL_LINEOUT1 0x62
+#define M98095_063_LVL_LINEOUT2 0x63
+#define M98095_064_LVL_HP_L 0x64
+#define M98095_065_LVL_HP_R 0x65
+#define M98095_066_LVL_RCV 0x66
+#define M98095_067_LVL_SPK_L 0x67
+#define M98095_068_LVL_SPK_R 0x68
+#define M98095_069_MICAGC_CFG 0x69
+#define M98095_06A_MICAGC_THRESH 0x6A
+#define M98095_06B_SPK_NOISEGATE 0x6B
+#define M98095_06C_DAI1_ALC1_TIME 0x6C
+#define M98095_06D_DAI1_ALC1_COMP 0x6D
+#define M98095_06E_DAI1_ALC1_EXPN 0x6E
+#define M98095_06F_DAI1_ALC1_GAIN 0x6F
+#define M98095_070_DAI1_ALC2_TIME 0x70
+#define M98095_071_DAI1_ALC2_COMP 0x71
+#define M98095_072_DAI1_ALC2_EXPN 0x72
+#define M98095_073_DAI1_ALC2_GAIN 0x73
+#define M98095_074_DAI1_ALC3_TIME 0x74
+#define M98095_075_DAI1_ALC3_COMP 0x75
+#define M98095_076_DAI1_ALC3_EXPN 0x76
+#define M98095_077_DAI1_ALC3_GAIN 0x77
+#define M98095_078_DAI2_ALC1_TIME 0x78
+#define M98095_079_DAI2_ALC1_COMP 0x79
+#define M98095_07A_DAI2_ALC1_EXPN 0x7A
+#define M98095_07B_DAI2_ALC1_GAIN 0x7B
+#define M98095_07C_DAI2_ALC2_TIME 0x7C
+#define M98095_07D_DAI2_ALC2_COMP 0x7D
+#define M98095_07E_DAI2_ALC2_EXPN 0x7E
+#define M98095_07F_DAI2_ALC2_GAIN 0x7F
+#define M98095_080_DAI2_ALC3_TIME 0x80
+#define M98095_081_DAI2_ALC3_COMP 0x81
+#define M98095_082_DAI2_ALC3_EXPN 0x82
+#define M98095_083_DAI2_ALC3_GAIN 0x83
+#define M98095_084_HP_NOISE_GATE 0x84
+#define M98095_085_AUX_ADC 0x85
+#define M98095_086_CFG_LINE 0x86
+#define M98095_087_CFG_MIC 0x87
+#define M98095_088_CFG_LEVEL 0x88
+#define M98095_089_JACK_DET_AUTO 0x89
+#define M98095_08A_JACK_DET_MANUAL 0x8A
+#define M98095_08B_JACK_KEYSCAN_DBC 0x8B
+#define M98095_08C_JACK_KEYSCAN_DLY 0x8C
+#define M98095_08D_JACK_KEY_THRESH 0x8D
+#define M98095_08E_JACK_DC_SLEW 0x8E
+#define M98095_08F_JACK_TEST_CFG 0x8F
+#define M98095_090_PWR_EN_IN 0x90
+#define M98095_091_PWR_EN_OUT 0x91
+#define M98095_092_PWR_EN_OUT 0x92
+#define M98095_093_BIAS_CTRL 0x93
+#define M98095_094_PWR_DAC_21 0x94
+#define M98095_095_PWR_DAC_03 0x95
+#define M98095_096_PWR_DAC_CK 0x96
+#define M98095_097_PWR_SYS 0x97
+
+#define M98095_0FF_REV_ID 0xFF
+
+#define M98095_REG_CNT (0xFF+1)
+#define M98095_REG_MAX_CACHED 0X97
+
+/* MAX98095 Registers Bit Fields */
+
+/* M98095_00F_HOST_CFG */
+#define M98095_SEG (1<<0)
+#define M98095_XTEN (1<<1)
+#define M98095_MDLLEN (1<<2)
+
+/* M98095_027_DAI1_CLKMODE, M98095_031_DAI2_CLKMODE, M98095_03B_DAI3_CLKMODE */
+#define M98095_CLKMODE_MASK 0xFF
+
+/* M98095_02A_DAI1_FORMAT, M98095_034_DAI2_FORMAT, M98095_03E_DAI3_FORMAT */
+#define M98095_DAI_MAS (1<<7)
+#define M98095_DAI_WCI (1<<6)
+#define M98095_DAI_BCI (1<<5)
+#define M98095_DAI_DLY (1<<4)
+#define M98095_DAI_TDM (1<<2)
+#define M98095_DAI_FSW (1<<1)
+#define M98095_DAI_WS (1<<0)
+
+/* M98095_02B_DAI1_CLOCK, M98095_035_DAI2_CLOCK, M98095_03F_DAI3_CLOCK */
+#define M98095_DAI_BSEL64 (1<<0)
+#define M98095_DAI_DOSR_DIV2 (0<<5)
+#define M98095_DAI_DOSR_DIV4 (1<<5)
+
+/* M98095_02C_DAI1_IOCFG, M98095_036_DAI2_IOCFG, M98095_040_DAI3_IOCFG */
+#define M98095_S1NORMAL (1<<6)
+#define M98095_S2NORMAL (2<<6)
+#define M98095_S3NORMAL (3<<6)
+#define M98095_SDATA (3<<0)
+
+/* M98095_02E_DAI1_FILTERS, M98095_038_DAI2_FILTERS, M98095_042_DAI3_FILTERS */
+#define M98095_DAI_DHF (1<<3)
+
+/* M98095_045_DSP_CFG */
+#define M98095_DSPNORMAL (5<<4)
+
+/* M98095_048_MIX_DAC_LR */
+#define M98095_DAI1L_TO_DACR (1<<7)
+#define M98095_DAI1R_TO_DACR (1<<6)
+#define M98095_DAI2M_TO_DACR (1<<5)
+#define M98095_DAI1L_TO_DACL (1<<3)
+#define M98095_DAI1R_TO_DACL (1<<2)
+#define M98095_DAI2M_TO_DACL (1<<1)
+#define M98095_DAI3M_TO_DACL (1<<0)
+
+/* M98095_049_MIX_DAC_M */
+#define M98095_DAI1L_TO_DACM (1<<3)
+#define M98095_DAI1R_TO_DACM (1<<2)
+#define M98095_DAI2M_TO_DACM (1<<1)
+#define M98095_DAI3M_TO_DACM (1<<0)
+
+/* M98095_04E_MIX_HP_CFG */
+#define M98095_HPNORMAL (3<<4)
+
+/* M98095_05F_LVL_MIC1, M98095_060_LVL_MIC2 */
+#define M98095_MICPRE_MASK (3<<5)
+#define M98095_MICPRE_SHIFT 5
+
+/* M98095_064_LVL_HP_L, M98095_065_LVL_HP_R */
+#define M98095_HP_MUTE (1<<7)
+
+/* M98095_066_LVL_RCV */
+#define M98095_REC_MUTE (1<<7)
+
+/* M98095_067_LVL_SPK_L, M98095_068_LVL_SPK_R */
+#define M98095_SP_MUTE (1<<7)
+
+/* M98095_087_CFG_MIC */
+#define M98095_MICSEL_MASK (3<<0)
+#define M98095_DIGMIC_L (1<<2)
+#define M98095_DIGMIC_R (1<<3)
+#define M98095_DIGMIC2L (1<<4)
+#define M98095_DIGMIC2R (1<<5)
+
+/* M98095_088_CFG_LEVEL */
+#define M98095_VSEN (1<<6)
+#define M98095_ZDEN (1<<5)
+#define M98095_BQ2EN (1<<3)
+#define M98095_BQ1EN (1<<2)
+#define M98095_EQ2EN (1<<1)
+#define M98095_EQ1EN (1<<0)
+
+/* M98095_090_PWR_EN_IN */
+#define M98095_INEN (1<<7)
+#define M98095_MB2EN (1<<3)
+#define M98095_MB1EN (1<<2)
+#define M98095_MBEN (3<<2)
+#define M98095_ADREN (1<<1)
+#define M98095_ADLEN (1<<0)
+
+/* M98095_091_PWR_EN_OUT */
+#define M98095_HPLEN (1<<7)
+#define M98095_HPREN (1<<6)
+#define M98095_SPLEN (1<<5)
+#define M98095_SPREN (1<<4)
+#define M98095_RECEN (1<<3)
+#define M98095_DALEN (1<<1)
+#define M98095_DAREN (1<<0)
+
+/* M98095_092_PWR_EN_OUT */
+#define M98095_SPK_FIXEDSPECTRUM (0<<4)
+#define M98095_SPK_SPREADSPECTRUM (1<<4)
+
+/* M98095_097_PWR_SYS */
+#define M98095_SHDNRUN (1<<7)
+#define M98095_PERFMODE (1<<3)
+#define M98095_HPPLYBACK (1<<2)
+#define M98095_PWRSV8K (1<<1)
+#define M98095_PWRSV (1<<0)
+
+#define M98095_COEFS_PER_BAND 5
+
+/* Equalizer filter coefficients */
+#define M98095_110_DAI1_EQ_BASE 0x10
+#define M98095_142_DAI2_EQ_BASE 0x42
+
+/* Biquad filter coefficients */
+#define M98095_174_DAI1_BQ_BASE 0x74
+#define M98095_17E_DAI2_BQ_BASE 0x7E
+
+/* function prototype */
+
+/*
+ * intialise max98095 sound codec device for the given configuration
+ *
+ * @param blob FDT node for codec values
+ * @param sampling_rate Sampling rate (Hz)
+ * @param mclk_freq MCLK Frequency (Hz)
+ * @param bits_per_sample bits per Sample (must be 16 or 24)
+ *
+ * @returns -1 for error and 0 Success.
+ */
+int max98095_init(const void *blob, int sampling_rate, int mclk_freq,
+ int bits_per_sample);
+
+#endif
diff --git a/drivers/sound/sound.c b/drivers/sound/sound.c
index fa8432d48a..a4bf4adcb3 100644
--- a/drivers/sound/sound.c
+++ b/drivers/sound/sound.c
@@ -31,6 +31,7 @@
#include <sound.h>
#include <asm/arch/sound.h>
#include "wm8994.h"
+#include "max98095.h"
/* defines */
#define SOUND_400_HZ 400
@@ -149,11 +150,15 @@ static int codec_init(const void *blob, struct i2stx_info *pi2s_tx)
pi2s_tx->samplingrate,
(pi2s_tx->samplingrate * (pi2s_tx->rfs)),
pi2s_tx->bitspersample, pi2s_tx->channels);
+ } else if (!strcmp(codectype, "max98095")) {
+ ret = max98095_init(blob, pi2s_tx->samplingrate,
+ (pi2s_tx->samplingrate * (pi2s_tx->rfs)),
+ pi2s_tx->bitspersample);
} else {
- debug("%s: Unknown code type %s\n", __func__,
- codectype);
+ debug("%s: Unknown codec type %s\n", __func__, codectype);
return -1;
}
+
if (ret) {
debug("%s: Codec init failed\n", __func__);
return -1;
diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h
index 1c624d4a54..2b9d6ac061 100644
--- a/include/configs/exynos5250-dt.h
+++ b/include/configs/exynos5250-dt.h
@@ -118,6 +118,11 @@
#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK
+/* Thermal Management Unit */
+#define CONFIG_EXYNOS_TMU
+#define CONFIG_CMD_DTT
+#define CONFIG_TMU_CMD_DTT
+
/* USB */
#define CONFIG_CMD_USB
#define CONFIG_USB_EHCI
@@ -297,6 +302,7 @@
#ifdef CONFIG_CMD_SOUND
#define CONFIG_SOUND
#define CONFIG_I2S
+#define CONFIG_SOUND_MAX98095
#define CONFIG_SOUND_WM8994
#endif
diff --git a/include/configs/snow.h b/include/configs/snow.h
new file mode 100644
index 0000000000..b8460fd1b4
--- /dev/null
+++ b/include/configs/snow.h
@@ -0,0 +1,33 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * Configuration settings for the SAMSUNG EXYNOS5 Snow board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_SNOW_H
+#define __CONFIG_SNOW_H
+
+#include <configs/exynos5250-dt.h>
+
+#undef CONFIG_DEFAULT_DEVICE_TREE
+#define CONFIG_DEFAULT_DEVICE_TREE exynos5250-snow
+
+#endif /* __CONFIG_SNOW_H */
diff --git a/include/fdtdec.h b/include/fdtdec.h
index 21894835d1..4fd1b670dc 100644
--- a/include/fdtdec.h
+++ b/include/fdtdec.h
@@ -83,7 +83,9 @@ enum fdt_compat_id {
COMPAT_SAMSUNG_EXYNOS_SPI, /* Exynos SPI */
COMPAT_SAMSUNG_EXYNOS_EHCI, /* Exynos EHCI controller */
COMPAT_SAMSUNG_EXYNOS_USB_PHY, /* Exynos phy controller for usb2.0 */
+ COMPAT_SAMSUNG_EXYNOS_TMU, /* Exynos TMU */
COMPAT_MAXIM_MAX77686_PMIC, /* MAX77686 PMIC */
+ COMPAT_MAXIM_98095_CODEC, /* MAX98095 Codec */
COMPAT_COUNT,
};
diff --git a/include/power/max77686_pmic.h b/include/power/max77686_pmic.h
index d949aced09..fdc7ca9e5a 100644
--- a/include/power/max77686_pmic.h
+++ b/include/power/max77686_pmic.h
@@ -155,4 +155,36 @@ enum {
EN_LDO = (0x3 << 6),
};
+/* Buck1 1 volt value */
+#define MAX77686_BUCK1OUT_1V 0x5
+#define MAX77686_BUCK1CTRL_EN (3 << 0)
+/* Buck2 1.3 volt value */
+#define MAX77686_BUCK2DVS1_1_3V 0x38
+#define MAX77686_BUCK2CTRL_ON (1 << 4)
+/* Buck3 1.0125 volt value */
+#define MAX77686_BUCK3DVS1_1_0125V 0x21
+#define MAX77686_BUCK3CTRL_ON (1 << 4)
+/* Buck4 1.2 volt value */
+#define MAX77686_BUCK4DVS1_1_2V 0x30
+#define MAX77686_BUCK4CTRL_ON (1 << 4)
+/* LDO2 1.5 volt value */
+#define MAX77686_LD02CTRL1_1_5V 0x1c
+/* LDO3 1.8 volt value */
+#define MAX77686_LD03CTRL1_1_8V 0x14
+/* LDO5 1.8 volt value */
+#define MAX77686_LD05CTRL1_1_8V 0x14
+/* LDO10 1.8 volt value */
+#define MAX77686_LD10CTRL1_1_8V 0x14
+/*
+ * MAX77686_REG_PMIC_32KHZ set to 32KH CP
+ * output is activated
+ */
+#define MAX77686_32KHCP_EN (1 << 1)
+/*
+ * MAX77686_REG_PMIC_BBAT set to
+ * Back up batery charger on and
+ * limit voltage setting to 3.5v
+ */
+#define MAX77686_BBCHOSTEN (1 << 0)
+#define MAX77686_BBCVS_3_5V (3 << 3)
#endif /* __MAX77686_PMIC_H_ */
diff --git a/include/sound.h b/include/sound.h
index d73839d9f0..94922f66da 100644
--- a/include/sound.h
+++ b/include/sound.h
@@ -28,6 +28,7 @@
enum en_sound_codec {
CODEC_WM_8994,
CODEC_WM_8995,
+ CODEC_MAX_98095,
CODEC_MAX
};
diff --git a/include/tmu.h b/include/tmu.h
new file mode 100644
index 0000000000..da07a2211e
--- /dev/null
+++ b/include/tmu.h
@@ -0,0 +1,46 @@
+/*
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ * Akshay Saraswat <akshay.s@samsung.com>
+ *
+ * Thermal Management Unit
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _TMU_H
+#define _TMU_H
+
+enum tmu_status_t {
+ TMU_STATUS_INIT = -1,
+ TMU_STATUS_NORMAL = 0,
+ TMU_STATUS_WARNING,
+ TMU_STATUS_TRIPPED,
+};
+
+/*
+ * Monitors status of the TMU device and exynos temperature
+ *
+ * @param temp pointer to the current temperature value
+ * @return enum tmu_status_t value, code indicating event to execute
+ * and -1 on error
+ */
+enum tmu_status_t tmu_monitor(int *temp);
+
+/*
+ * Initialize TMU device
+ *
+ * @param blob FDT blob
+ * @return int value, 0 for success
+ */
+int tmu_init(const void *blob);
+#endif /* _THERMAL_H_ */
diff --git a/lib/fdtdec.c b/lib/fdtdec.c
index 43f29f5c6b..b232096f92 100644
--- a/lib/fdtdec.c
+++ b/lib/fdtdec.c
@@ -58,7 +58,9 @@ static const char * const compat_names[COMPAT_COUNT] = {
COMPAT(SAMSUNG_EXYNOS_SPI, "samsung,exynos-spi"),
COMPAT(SAMSUNG_EXYNOS_EHCI, "samsung,exynos-ehci"),
COMPAT(SAMSUNG_EXYNOS_USB_PHY, "samsung,exynos-usb-phy"),
+ COMPAT(SAMSUNG_EXYNOS_TMU, "samsung,exynos-tmu"),
COMPAT(MAXIM_MAX77686_PMIC, "maxim,max77686_pmic"),
+ COMPAT(MAXIM_98095_CODEC, "maxim,max98095-codec"),
};
const char *fdtdec_get_compatible(enum fdt_compat_id id)