| Age | Commit message (Collapse) | Author |
|---|
|
Commit 288dab8a35a0 ("block: add a separate operation type for secure
erase") split REQ_OP_SECURE_ERASE from REQ_OP_DISCARD without considering
all the places REQ_OP_DISCARD was being used to mean either. Fix those.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 288dab8a35a0 ("block: add a separate operation type for secure erase")
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Since commit 63a4cc24867d, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"A few updates and fixes:
- move the suppressing of the __builtin_return_address >0 warning to
the tracing directory only.
- metag recordmcount fix for newer glibc's
- two tracing histogram fixes that were reported by KASAN"
* tag 'trace-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix use-after-free in hist_register_trigger()
tracing: Fix use-after-free in hist_unreg_all/hist_enable_unreg_all
Makefile: Mute warning for __builtin_return_address(>0) for tracing only
ftrace/recordmcount: Work around for addition of metag magic but not relocations
|
|
This fixes a use-after-free case flagged by KASAN; make sure the test
happens before the potential free in this case.
Link: http://lkml.kernel.org/r/48fd74ab61bebd7dca9714386bb47d7c5ccd6a7b.1467247517.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
While running tools/testing/selftests test suite with KASAN, Dmitry
Vyukov hit the following use-after-free report:
==================================================================
BUG: KASAN: use-after-free in hist_unreg_all+0x1a1/0x1d0 at addr
ffff880031632cc0
Read of size 8 by task ftracetest/7413
==================================================================
BUG kmalloc-128 (Not tainted): kasan: bad access detected
------------------------------------------------------------------
This fixes the problem, along with the same problem in
hist_enable_unreg_all().
Link: http://lkml.kernel.org/r/c3d05b79e42555b6e36a3a99aae0e37315ee5304.1467247517.git.tom.zanussi@linux.intel.com
Cc: Dmitry Vyukov <dvyukov@google.com>
[Copied Steve's hist_enable_unreg_all() fix to hist_unreg_all()]
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
With the latest gcc compilers, they give a warning if
__builtin_return_address() parameter is greater than 0. That is because if
it is used by a function called by a top level function (or in the case of
the kernel, by assembly), it can try to access stack frames outside the
stack and crash the system.
The tracing system uses __builtin_return_address() of up to 2! But it is
well aware of the dangers that it may have, and has even added precautions
to protect against it (see the thunk code in arch/x86/entry/thunk*.S)
Linus originally added KBUILD_CFLAGS that would suppress the warning for the
entire kernel, as simply adding KBUILD_CFLAGS to the tracing directory
wouldn't work. The tracing directory plays a bit with the CFLAGS and
requires a little more logic.
This adds that special logic to only suppress the warning for the tracing
directory. If it is used anywhere else outside of tracing, the warning will
still be triggered.
Link: http://lkml.kernel.org/r/20160728223043.51996267@grimm.local.home
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This is mostly clean ups and small fixes. Some of the more visible
changes are:
- The function pid code uses the event pid filtering logic
- [ku]probe events have access to current->comm
- trace_printk now has sample code
- PCI devices now trace physical addresses
- stack tracing has less unnessary functions traced"
* tag 'trace-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
printk, tracing: Avoiding unneeded blank lines
tracing: Use __get_str() when manipulating strings
tracing, RAS: Cleanup on __get_str() usage
tracing: Use outer () on __get_str() definition
ftrace: Reduce size of function graph entries
tracing: Have HIST_TRIGGERS select TRACING
tracing: Using for_each_set_bit() to simplify trace_pid_write()
ftrace: Move toplevel init out of ftrace_init_tracefs()
tracing/function_graph: Fix filters for function_graph threshold
tracing: Skip more functions when doing stack tracing of events
tracing: Expose CPU physical addresses (resource values) for PCI devices
tracing: Show the preempt count of when the event was called
tracing: Add trace_printk sample code
tracing: Choose static tp_printk buffer by explicit nesting count
tracing: expose current->comm to [ku]probe events
ftrace: Have set_ftrace_pid use the bitmap like events do
tracing: Move pid_list write processing into its own function
tracing: Move the pid_list seq_file functions to be global
tracing: Move filtered_pid helper functions into trace.c
tracing: Make the pid filtering helper functions global
|
|
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
|
|
Pull block driver updates from Jens Axboe:
"This branch also contains core changes. I've come to the conclusion
that from 4.9 and forward, I'll be doing just a single branch. We
often have dependencies between core and drivers, and it's hard to
always split them up appropriately without pulling core into drivers
when that happens.
That said, this contains:
- separate secure erase type for the core block layer, from
Christoph.
- set of discard fixes, from Christoph.
- bio shrinking fixes from Christoph, as a followup up to the
op/flags change in the core branch.
- map and append request fixes from Christoph.
- NVMeF (NVMe over Fabrics) code from Christoph. This is pretty
exciting!
- nvme-loop fixes from Arnd.
- removal of ->driverfs_dev from Dan, after providing a
device_add_disk() helper.
- bcache fixes from Bhaktipriya and Yijing.
- cdrom subchannel read fix from Vchannaiah.
- set of lightnvm updates from Wenwei, Matias, Johannes, and Javier.
- set of drbd updates and fixes from Fabian, Lars, and Philipp.
- mg_disk error path fix from Bart.
- user notification for failed device add for loop, from Minfei.
- NVMe in general:
+ NVMe delay quirk from Guilherme.
+ SR-IOV support and command retry limits from Keith.
+ fix for memory-less NUMA node from Masayoshi.
+ use UINT_MAX for discard sectors, from Minfei.
+ cancel IO fixes from Ming.
+ don't allocate unused major, from Neil.
+ error code fixup from Dan.
+ use constants for PSDT/FUSE from James.
+ variable init fix from Jay.
+ fabrics fixes from Ming, Sagi, and Wei.
+ various fixes"
* 'for-4.8/drivers' of git://git.kernel.dk/linux-block: (115 commits)
nvme/pci: Provide SR-IOV support
nvme: initialize variable before logical OR'ing it
block: unexport various bio mapping helpers
scsi/osd: open code blk_make_request
target: stop using blk_make_request
block: simplify and export blk_rq_append_bio
block: ensure bios return from blk_get_request are properly initialized
virtio_blk: use blk_rq_map_kern
memstick: don't allow REQ_TYPE_BLOCK_PC requests
block: shrink bio size again
block: simplify and cleanup bvec pool handling
block: get rid of bio_rw and READA
block: don't ignore -EOPNOTSUPP blkdev_issue_write_same
block: introduce BLKDEV_DISCARD_ZERO to fix zeroout
NVMe: don't allocate unused nvme_major
nvme: avoid crashes when node 0 is memoryless node.
nvme: Limit command retries
loop: Make user notify for adding loop device failed
nvme-loop: fix nvme-loop Kconfig dependencies
nvmet: fix return value check in nvmet_subsys_alloc()
...
|
|
Pull core block updates from Jens Axboe:
- the big change is the cleanup from Mike Christie, cleaning up our
uses of command types and modified flags. This is what will throw
some merge conflicts
- regression fix for the above for btrfs, from Vincent
- following up to the above, better packing of struct request from
Christoph
- a 2038 fix for blktrace from Arnd
- a few trivial/spelling fixes from Bart Van Assche
- a front merge check fix from Damien, which could cause issues on
SMR drives
- Atari partition fix from Gabriel
- convert cfq to highres timers, since jiffies isn't granular enough
for some devices these days. From Jan and Jeff
- CFQ priority boost fix idle classes, from me
- cleanup series from Ming, improving our bio/bvec iteration
- a direct issue fix for blk-mq from Omar
- fix for plug merging not involving the IO scheduler, like we do for
other types of merges. From Tahsin
- expose DAX type internally and through sysfs. From Toshi and Yigal
* 'for-4.8/core' of git://git.kernel.dk/linux-block: (76 commits)
block: Fix front merge check
block: do not merge requests without consulting with io scheduler
block: Fix spelling in a source code comment
block: expose QUEUE_FLAG_DAX in sysfs
block: add QUEUE_FLAG_DAX for devices to advertise their DAX support
Btrfs: fix comparison in __btrfs_map_block()
block: atari: Return early for unsupported sector size
Doc: block: Fix a typo in queue-sysfs.txt
cfq-iosched: Charge at least 1 jiffie instead of 1 ns
cfq-iosched: Fix regression in bonnie++ rewrite performance
cfq-iosched: Convert slice_resid from u64 to s64
block: Convert fifo_time from ulong to u64
blktrace: avoid using timespec
block/blk-cgroup.c: Declare local symbols static
block/bio-integrity.c: Add #include "blk.h"
block/partition-generic.c: Remove a set-but-not-used variable
block: bio: kill BIO_MAX_SIZE
cfq-iosched: temporarily boost queue priority for idle classes
block: drbd: avoid to use BIO_MAX_SIZE
block: bio: remove BIO_MAX_SECTORS
...
|
|
This allows user memory to be written to during the course of a kprobe.
It shouldn't be used to implement any kind of security mechanism
because of TOC-TOU attacks, but rather to debug, divert, and
manipulate execution of semi-cooperative processes.
Although it uses probe_kernel_write, we limit the address space
the probe can write into by checking the space with access_ok.
We do this as opposed to calling copy_to_user directly, in order
to avoid sleeping. In addition we ensure the threads's current fs
/ segment is USER_DS and the thread isn't exiting nor a kernel thread.
Given this feature is meant for experiments, and it has a risk of
crashing the system, and running programs, we print a warning on
when a proglet that attempts to use this helper is installed,
along with the pid and process name.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kernel/trace/bpf_trace.c: In function 'bpf_event_output':
kernel/trace/bpf_trace.c:312: error: unknown field 'next' specified in initializer
kernel/trace/bpf_trace.c:312: warning: missing braces around initializer
kernel/trace/bpf_trace.c:312: warning: (near initialization for 'raw.frag.<anonymous>')
Fixes: 555c8a8623a3a87 ("bpf: avoid stack copy and use skb ctx for event output")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This work addresses a couple of issues bpf_skb_event_output()
helper currently has: i) We need two copies instead of just a
single one for the skb data when it should be part of a sample.
The data can be non-linear and thus needs to be extracted via
bpf_skb_load_bytes() helper first, and then copied once again
into the ring buffer slot. ii) Since bpf_skb_load_bytes()
currently needs to be used first, the helper needs to see a
constant size on the passed stack buffer to make sure BPF
verifier can do sanity checks on it during verification time.
Thus, just passing skb->len (or any other non-constant value)
wouldn't work, but changing bpf_skb_load_bytes() is also not
the proper solution, since the two copies are generally still
needed. iii) bpf_skb_load_bytes() is just for rather small
buffers like headers, since they need to sit on the limited
BPF stack anyway. Instead of working around in bpf_skb_load_bytes(),
this work improves the bpf_skb_event_output() helper to address
all 3 at once.
We can make use of the passed in skb context that we have in
the helper anyway, and use some of the reserved flag bits as
a length argument. The helper will use the new __output_custom()
facility from perf side with bpf_skb_copy() as callback helper
to walk and extract the data. It will pass the data for setup
to bpf_event_output(), which generates and pushes the raw record
with an additional frag part. The linear data used in the first
frag of the record serves as programmatically defined meta data
passed along with the appended sample.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split the bpf_perf_event_output() helper as a preparation into
two parts. The new bpf_perf_event_output() will prepare the raw
record itself and test for unknown flags from BPF trace context,
where the __bpf_perf_event_output() does the core work. The
latter will be reused later on from bpf_event_output() directly.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for non-linear data on raw records. It
extends raw records to have one or multiple fragments that will
be written linearly into the ring slot, where each fragment can
optionally have a custom callback handler to walk and extract
complex, possibly non-linear data.
If a callback handler is provided for a fragment, then the new
__output_custom() will be used instead of __output_copy() for
the perf_output_sample() part. perf_prepare_sample() does all
the size calculation only once, so perf_output_sample() doesn't
need to redo the same work anymore, meaning real_size and padding
will be cached in the raw record. The raw record becomes 32 bytes
in size without holes; to not increase it further and to avoid
doing unnecessary recalculations in fast-path, we can reuse
next pointer of the last fragment, idea here is borrowed from
ZERO_OR_NULL_PTR(), which should keep the perf_output_sample()
path for PERF_SAMPLE_RAW minimal.
This facility is needed for BPF's event output helper as a first
user that will, in a follow-up, add an additional perf_raw_frag
to its perf_raw_record in order to be able to more efficiently
dump skb context after a linear head meta data related to it.
skbs can be non-linear and thus need a custom output function to
dump buffers. Currently, the skb data needs to be copied twice;
with the help of __output_custom() this work only needs to be
done once. Future users could be things like XDP/BPF programs
that work on different context though and would thus also have
a different callback function.
The few users of raw records are adapted to initialize their frag
data from the raw record itself, no change in behavior for them.
The code is based upon a PoC diff provided by Peter Zijlstra [1].
[1] http://thread.gmane.org/gmane.linux.network/421294
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
over time there were multiple requests to access different data
structures and fields of task_struct current, so finally add
the helper to access 'current' as-is. Tracing bpf programs will do
the rest of walking the pointers via bpf_probe_read().
Note that current can be null and bpf program has to deal it with,
but even dumb passing null into bpf_probe_read() is still safe.
Suggested-by: Brendan Gregg <brendan.d.gregg@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently ftrace_graph_ent{,_entry} and ftrace_graph_ret{,_entry} struct
can have padding bytes at the end due to alignment in 64-bit data type.
As these data are recorded so frequently, those paddings waste
non-negligible space. As the ring buffer maintains alignment properly
for each architecture, just to remove the extra padding using 'packed'
attribute.
ftrace_graph_ent_entry: 24 -> 20
ftrace_graph_ret_entry: 48 -> 44
Also I moved the 'overrun' field in struct ftrace_graph_ret to minimize
the padding in the middle.
Tested on x86_64 only.
Link: http://lkml.kernel.org/r/1467197808-13578-1-git-send-email-namhyung@kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: linux-arch@vger.kernel.org
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The kbuild test robot reported a compile error if HIST_TRIGGERS was
enabled but nothing else that selected TRACING was configured in.
HIST_TRIGGERS should directly select it and not rely on anything else
to do it.
Link: http://lkml.kernel.org/r/57791866.8080505@linux.intel.com
Reported-by: kbuild test robot <fennguang.wu@intel.com>
Fixes: 7ef224d1d0e3a ("tracing: Add 'hist' event trigger command")
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Using for_each_set_bit() to simplify the code.
Link: http://lkml.kernel.org/r/1467645004-11169-1-git-send-email-weiyj_lk@163.com
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Commit 345ddcc882d8 ("ftrace: Have set_ftrace_pid use the bitmap like events
do") placed ftrace_init_tracefs into the instance creation, and encapsulated
the top level updating with an if conditional, as the top level only gets
updated at boot up. Unfortunately, this triggers section mismatch errors as
the init functions are called from a function that can be called later, and
the section mismatch logic is unaware of the if conditional that would
prevent it from happening at run time.
To make everyone happy, create a separate ftrace_init_tracefs_toplevel()
routine that only gets called by init functions, and this will be what calls
other init functions for the toplevel directory.
Link: http://lkml.kernel.org/r/20160704102139.19cbc0d9@gandalf.local.home
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 345ddcc882d8 ("ftrace: Have set_ftrace_pid use the bitmap like events do")
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Follow-up commit to 1e33759c788c ("bpf, trace: add BPF_F_CURRENT_CPU
flag for bpf_perf_event_output") to add the same functionality into
bpf_perf_event_read() helper. The split of index into flags and index
component is also safe here, since such large maps are rejected during
map allocation time.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently have two invocations, which is unnecessary. Fetch it only
once and use the smp_processor_id() variant, so we also get preemption
checks along with it when DEBUG_PREEMPT is set.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some minor cleanups: i) Remove the unlikely() from fd array map lookups
and let the CPU branch predictor do its job, scenarios where there is not
always a map entry are very well valid. ii) Move the attribute type check
in the bpf_perf_event_read() helper a bit earlier so it's consistent wrt
checks with bpf_perf_event_output() helper as well. iii) remove some
comments that are self-documenting in kprobe_prog_is_valid_access() and
therefore make it consistent to tp_prog_is_valid_access() as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"I've been traveling so this accumulates more than week or so of bug
fixing. It perhaps looks a little worse than it really is.
1) Fix deadlock in ath10k driver, from Ben Greear.
2) Increase scan timeout in iwlwifi, from Luca Coelho.
3) Unbreak STP by properly reinjecting STP packets back into the
stack. Regression fix from Ido Schimmel.
4) Mediatek driver fixes (missing malloc failure checks, leaking of
scratch memory, wrong indexing when mapping TX buffers, etc.) from
John Crispin.
5) Fix endianness bug in icmpv6_err() handler, from Hannes Frederic
Sowa.
6) Fix hashing of flows in UDP in the ruseport case, from Xuemin Su.
7) Fix netlink notifications in ovs for tunnels, delete link messages
are never emitted because of how the device registry state is
handled. From Nicolas Dichtel.
8) Conntrack module leaks kmemcache on unload, from Florian Westphal.
9) Prevent endless jump loops in nft rules, from Liping Zhang and
Pablo Neira Ayuso.
10) Not early enough spinlock initialization in mlx4, from Eric
Dumazet.
11) Bind refcount leak in act_ipt, from Cong WANG.
12) Missing RCU locking in HTB scheduler, from Florian Westphal.
13) Several small MACSEC bug fixes from Sabrina Dubroca (missing RCU
barrier, using heap for SG and IV, and erroneous use of async flag
when allocating AEAD conext.)
14) RCU handling fix in TIPC, from Ying Xue.
15) Pass correct protocol down into ipv4_{update_pmtu,redirect}() in
SIT driver, from Simon Horman.
16) Socket timer deadlock fix in TIPC from Jon Paul Maloy.
17) Fix potential deadlock in team enslave, from Ido Schimmel.
18) Memory leak in KCM procfs handling, from Jiri Slaby.
19) ESN generation fix in ipv4 ESP, from Herbert Xu.
20) Fix GFP_KERNEL allocations with locks held in act_ife, from Cong
WANG.
21) Use after free in netem, from Eric Dumazet.
22) Uninitialized last assert time in multicast router code, from Tom
Goff.
23) Skip raw sockets in sock_diag destruction broadcast, from Willem
de Bruijn.
24) Fix link status reporting in thunderx, from Sunil Goutham.
25) Limit resegmentation of retransmit queue so that we do not
retransmit too large GSO frames. From Eric Dumazet.
26) Delay bpf program release after grace period, from Daniel
Borkmann"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (141 commits)
openvswitch: fix conntrack netlink event delivery
qed: Protect the doorbell BAR with the write barriers.
neigh: Explicitly declare RCU-bh read side critical section in neigh_xmit()
e1000e: keep VLAN interfaces functional after rxvlan off
cfg80211: fix proto in ieee80211_data_to_8023 for frames without LLC header
qlcnic: use the correct ring in qlcnic_83xx_process_rcv_ring_diag()
bpf, perf: delay release of BPF prog after grace period
net: bridge: fix vlan stats continue counter
tcp: do not send too big packets at retransmit time
ibmvnic: fix to use list_for_each_safe() when delete items
net: thunderx: Fix TL4 configuration for secondary Qsets
net: thunderx: Fix link status reporting
net/mlx5e: Reorganize ethtool statistics
net/mlx5e: Fix number of PFC counters reported to ethtool
net/mlx5e: Prevent adding the same vxlan port
net/mlx5e: Check for BlueFlame capability before allocating SQ uar
net/mlx5e: Change enum to better reflect usage
net/mlx5: Add ConnectX-5 PCIe 4.0 to list of supported devices
net/mlx5: Update command strings
net: marvell: Add separate config ANEG function for Marvell 88E1111
...
|
|
Function graph tracer currently ignores filters if tracing_thresh is set.
For example, even if set_ftrace_pid is set, then its ignored if tracing_thresh
set, resulting in all processes being traced.
To fix this, we reuse the same entry function as when tracing_thresh is not
set and do everything as in the regular case except for writing the function entry
to the ring buffer.
Link: http://lkml.kernel.org/r/1466228694-2677-1-git-send-email-agnel.joel@gmail.com
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Joel Fernandes <agnel.joel@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
# echo 1 > options/stacktrace
# echo 1 > events/sched/sched_switch/enable
# cat trace
<idle>-0 [002] d..2 1982.525169: <stack trace>
=> save_stack_trace
=> __ftrace_trace_stack
=> trace_buffer_unlock_commit_regs
=> event_trigger_unlock_commit
=> trace_event_buffer_commit
=> trace_event_raw_event_sched_switch
=> __schedule
=> schedule
=> schedule_preempt_disabled
=> cpu_startup_entry
=> start_secondary
The above shows that we are seeing 6 functions before ever making it to the
caller of the sched_switch event.
# echo stacktrace > events/sched/sched_switch/trigger
# cat trace
<idle>-0 [002] d..3 2146.335208: <stack trace>
=> trace_event_buffer_commit
=> trace_event_raw_event_sched_switch
=> __schedule
=> schedule
=> schedule_preempt_disabled
=> cpu_startup_entry
=> start_secondary
The stacktrace trigger isn't as bad, because it adds its own skip to the
stacktracing, but still has two events extra.
One issue is that if the stacktrace passes its own "regs" then there should
be no addition to the skip, as the regs will not include the functions being
called. This was an issue that was fixed by commit 7717c6be6999 ("tracing:
Fix stacktrace skip depth in trace_buffer_unlock_commit_regs()" as adding
the skip number for kprobes made the probes not have any stack at all.
But since this is only an issue when regs is being used, a skip should be
added if regs is NULL. Now we have:
# echo 1 > options/stacktrace
# echo 1 > events/sched/sched_switch/enable
# cat trace
<idle>-0 [000] d..2 1297.676333: <stack trace>
=> __schedule
=> schedule
=> schedule_preempt_disabled
=> cpu_startup_entry
=> rest_init
=> start_kernel
=> x86_64_start_reservations
=> x86_64_start_kernel
# echo stacktrace > events/sched/sched_switch/trigger
# cat trace
<idle>-0 [002] d..3 1370.759745: <stack trace>
=> __schedule
=> schedule
=> schedule_preempt_disabled
=> cpu_startup_entry
=> start_secondary
And kprobes are not touched.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Previously, mmio_print_pcidev() put "user" addresses in the trace buffer.
On most architectures, these are the same as CPU physical addresses, but on
microblaze, mips, powerpc, and sparc, they may be something else, typically
a raw BAR value (a bus address as opposed to a CPU address).
Always expose the CPU physical address to avoid this arch-dependent
behavior.
This change should have no user-visible effect because this file currently
depends on CONFIG_HAVE_MMIOTRACE_SUPPORT, which is only defined for x86,
and pci_resource_to_user() is a no-op on x86.
Link: http://lkml.kernel.org/r/20160511190657.5898.4248.stgit@bhelgaas-glaptop2.roam.corp.google.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Because tracepoint callbacks are done with preemption enabled, the trace
events are always called with preempt disable due to the
rcu_read_lock_sched_notrace() in __DO_TRACE(). This causes the preempt count
shown in the recorded trace event to be inaccurate. It is always one more
that what the preempt_count was when the tracepoint was called.
If CONFIG_PREEMPT is enabled, subtract 1 from the preempt_count before
recording it in the trace buffer.
Link: http://lkml.kernel.org/r/20160525132537.GA10808@linutronix.de
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Currently, the trace_printk code chooses which static buffer to use based
on what type of atomic context (NMI, IRQ, etc) it's in. Simplify the
code and make it more robust: simply count the nesting depth and choose
a buffer based on the current nesting depth.
The new code will only drop an event if we nest more than 4 deep,
and the old code was guaranteed to malfunction if that happened.
Link: http://lkml.kernel.org/r/07ab03aecfba25fcce8f9a211b14c9c5e2865c58.1464289095.git.luto@kernel.org
Acked-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
ftrace is very quick to give up on saving the task command line (see
`trace_save_cmdline()`). The workaround for events which really care
about the command line is to explicitly assign it as part of the entry.
However, this doesn't work for kprobe events, as there's no
straightforward way to get access to current->comm. Add a kprobe/uprobe
event variable $comm which provides exactly that.
Link: http://lkml.kernel.org/r/f59b472033b943a370f5f48d0af37698f409108f.1465435894.git.osandov@fb.com
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Convert set_ftrace_pid to use the bitmap like set_event_pid does. This
allows for instances to use the pid filtering as well, and will allow for
function-fork option to set if the children of a traced function should be
traced or not.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The addition of PIDs into a pid_list via the write operation of
set_event_pid is a bit complex. The same operation will be needed for
function tracing pids. Move the code into its own generic function in
trace.c, so that we can avoid duplication of this code.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
To allow other aspects of ftrace to use the pid_list logic, we need to reuse
the seq_file functions. Making the generic part into functions that can be
called by other files will help in this regard.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
As the filtered_pid functions are going to be used by function tracer as
well as trace_events, move the code into the generic trace.c file.
The functions moved are:
trace_find_filtered_pid()
trace_ignore_this_task()
trace_filter_add_remove_task()
Kernel Doc text was also added.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Make the functions used for pid filtering global for tracing, such that the
function tracer can use the pid code as well.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
If a task uses a non constant string for the format parameter in
trace_printk(), then the trace_printk_fmt variable is set to NULL. This
variable is then saved in the __trace_printk_fmt section.
The function hold_module_trace_bprintk_format() checks to see if duplicate
formats are used by modules, and reuses them if so (saves them to the list
if it is new). But this function calls lookup_format() that does a strcmp()
to the value (which is now NULL) and can cause a kernel oops.
This wasn't an issue till 3debb0a9ddb ("tracing: Fix trace_printk() to print
when not using bprintk()") which added "__used" to the trace_printk_fmt
variable, and before that, the kernel simply optimized it out (no NULL value
was saved).
The fix is simply to handle the NULL pointer in lookup_format() and have the
caller ignore the value if it was NULL.
Link: http://lkml.kernel.org/r/1464769870-18344-1-git-send-email-zhengjun.xing@intel.com
Reported-by: xingzhen <zhengjun.xing@intel.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Fixes: 3debb0a9ddb ("tracing: Fix trace_printk() to print when not using bprintk()")
Cc: stable@vger.kernel.org # v3.5+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The blktrace code stores the current time in a 32-bit word in its
user interface. This is a bad idea because 32-bit seconds overflow
at some point.
We probably have until 2106 before this one overflows, as it seems
to use an 'unsigned' variable, but we should confirm that user
space treats it the same way.
Aside from this, we want to stop using 'struct timespec' here,
so I'm adding a comment about the overflow and change the code
to use timespec64 instead to make the loss of range more obvious.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The behavior of perf event arrays are quite different from all
others as they are tightly coupled to perf event fds, f.e. shown
recently by commit e03e7ee34fdd ("perf/bpf: Convert perf_event_array
to use struct file") to make refcounting on perf event more robust.
A remaining issue that the current code still has is that since
additions to the perf event array take a reference on the struct
file via perf_event_get() and are only released via fput() (that
cleans up the perf event eventually via perf_event_release_kernel())
when the element is either manually removed from the map from user
space or automatically when the last reference on the perf event
map is dropped. However, this leads us to dangling struct file's
when the map gets pinned after the application owning the perf
event descriptor exits, and since the struct file reference will
in such case only be manually dropped or via pinned file removal,
it leads to the perf event living longer than necessary, consuming
needlessly resources for that time.
Relations between perf event fds and bpf perf event map fds can be
rather complex. F.e. maps can act as demuxers among different perf
event fds that can possibly be owned by different threads and based
on the index selection from the program, events get dispatched to
one of the per-cpu fd endpoints. One perf event fd (or, rather a
per-cpu set of them) can also live in multiple perf event maps at
the same time, listening for events. Also, another requirement is
that perf event fds can get closed from application side after they
have been attached to the perf event map, so that on exit perf event
map will take care of dropping their references eventually. Likewise,
when such maps are pinned, the intended behavior is that a user
application does bpf_obj_get(), puts its fds in there and on exit
when fd is released, they are dropped from the map again, so the map
acts rather as connector endpoint. This also makes perf event maps
inherently different from program arrays as described in more detail
in commit c9da161c6517 ("bpf: fix clearing on persistent program
array maps").
To tackle this, map entries are marked by the map struct file that
added the element to the map. And when the last reference to that map
struct file is released from user space, then the tracked entries
are purged from the map. This is okay, because new map struct files
instances resp. frontends to the anon inode are provided via
bpf_map_new_fd() that is called when we invoke bpf_obj_get_user()
for retrieving a pinned map, but also when an initial instance is
created via map_create(). The rest is resolved by the vfs layer
automatically for us by keeping reference count on the map's struct
file. Any concurrent updates on the map slot are fine as well, it
just means that perf_event_fd_array_release() needs to delete less
of its own entires.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
similar to bpf_perf_event_output() the bpf_perf_event_read() helper
needs to check the type of the perf_event before reading the counter.
Fixes: a43eec304259 ("bpf: introduce bpf_perf_event_output() helper")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ctx structure passed into bpf programs is different depending on bpf
program type. The verifier incorrectly marked ctx->data and ctx->data_end
access based on ctx offset only. That caused loads in tracing programs
int bpf_prog(struct pt_regs *ctx) { .. ctx->ax .. }
to be incorrectly marked as PTR_TO_PACKET which later caused verifier
to reject the program that was actually valid in tracing context.
Fix this by doing program type specific matching of ctx offsets.
Fixes: 969bf05eb3ce ("bpf: direct packet access")
Reported-by: Sasha Goldshtein <goldshtn@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of overloading the discard support with the REQ_SECURE flag.
Use the opportunity to rename the queue flag as well, and remove the
dead checks for this flag in the RAID 1 and RAID 10 drivers that don't
claim support for secure erase.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
In bpf_perf_event_read() and bpf_perf_event_output(), we must use
READ_ONCE() for fetching the struct file pointer, which could get
updated concurrently, so we must prevent the compiler from potential
refetching.
We already do this with tail calls for fetching the related bpf_prog,
but not so on stored perf events. Semantics for both are the same
with regards to updates.
Fixes: a43eec304259 ("bpf: introduce bpf_perf_event_output() helper")
Fixes: 35578d798400 ("bpf: Implement function bpf_perf_event_read() that get the selected hardware PMU conuter")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To avoid confusion between REQ_OP_FLUSH, which is handled by
request_fn drivers, and upper layers requesting the block layer
perform a flush sequence along with possibly a WRITE, this patch
renames REQ_FLUSH to REQ_PREFLUSH.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This adds a REQ_OP_FLUSH operation that is sent to request_fn
based drivers by the block layer's flush code, instead of
sending requests with the request->cmd_flags REQ_FLUSH bit set.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Have blktrace use the req/bio op accessor to get the REQ_OP.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull motr tracing updates from Steven Rostedt:
"Three more changes.
- I forgot that I had another selftest to stress test the ftrace
instance creation. It was actually suppose to go into the 4.6
merge window, but I never committed it. I almost forgot about it
again, but noticed it was missing from your tree.
- Soumya PN sent me a clean up patch to not disable interrupts when
taking the tasklist_lock for read, as it's unnecessary because that
lock is never taken for write in irq context.
- Newer gcc's can cause the jump in the function_graph code to the
global ftrace_stub label to be a short jump instead of a long one.
As that jump is dynamically converted to jump to the trace code to
do function graph tracing, and that conversion expects a long jump
it can corrupt the ftrace_stub itself (it's directly after that
call). One way to prevent gcc from using a short jump is to
declare the ftrace_stub as a weak function, which we do here to
keep gcc from optimizing too much"
* tag 'trace-v4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/x86: Set ftrace_stub to weak to prevent gcc from using short jumps to it
ftrace: Don't disable irqs when taking the tasklist_lock read_lock
ftracetest: Add instance created, delete, read and enable event test
|
|
In ftrace.c inside the function alloc_retstack_tasklist() (which will be
invoked when function_graph tracing is on) the tasklist_lock is being
held as reader while iterating through a list of threads. Here the lock
is being held as reader with irqs disabled. The tasklist_lock is never
write_locked in interrupt context so it is safe to not disable interrupts
for the duration of read_lock in this block which, can be significant,
given the block of code iterates through all threads. Hence changing the
code to call read_lock() and read_unlock() instead of read_lock_irqsave()
and read_unlock_irqrestore().
A similar change was made in commits: 8063e41d2ffc ("tracing: Change
syscall_*regfunc() to check PF_KTHREAD and use for_each_process_thread()")'
and 3472eaa1f12e ("sched: normalize_rt_tasks(): Don't use _irqsave for
tasklist_lock, use task_rq_lock()")'
Link: http://lkml.kernel.org/r/1463500874-77480-1-git-send-email-soumya.p.n@hpe.com
Signed-off-by: Soumya PN <soumya.p.n@hpe.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Support for Power ISA 3.0 (Power9) Radix Tree MMU from Aneesh Kumar K.V
- Live patching support for ppc64le (also merged via livepatching.git)
Various cleanups & minor fixes from:
- Aaro Koskinen, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Chris Smart, Daniel Axtens, Frederic Barrat, Gavin Shan, Ian Munsie,
Lennart Sorensen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring,
Michael Ellerman, Oliver O'Halloran, Paul Gortmaker, Paul Mackerras,
Rashmica Gupta, Russell Currey, Suraj Jitindar Singh, Thiago Jung
Bauermann, Valentin Rothberg, Vipin K Parashar.
General:
- Update LMB associativity index during DLPAR add/remove from Nathan
Fontenot
- Fix branching to OOL handlers in relocatable kernel from Hari Bathini
- Add support for userspace Power9 copy/paste from Chris Smart
- Always use STRICT_MM_TYPECHECKS from Michael Ellerman
- Add mask of possible MMU features from Michael Ellerman
PCI:
- Enable pass through of NVLink to guests from Alexey Kardashevskiy
- Cleanups in preparation for powernv PCI hotplug from Gavin Shan
- Don't report error in eeh_pe_reset_and_recover() from Gavin Shan
- Restore initial state in eeh_pe_reset_and_recover() from Gavin Shan
- Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell"
from Guilherme G Piccoli
- Remove the dependency on EEH struct in DDW mechanism from Guilherme
G Piccoli
selftests:
- Test cp_abort during context switch from Chris Smart
- Add several tests for transactional memory support from Rashmica
Gupta
perf:
- Add support for sampling interrupt register state from Anju T
- Add support for unwinding perf-stackdump from Chandan Kumar
cxl:
- Configure the PSL for two CAPI ports on POWER8NVL from Philippe
Bergheaud
- Allow initialization on timebase sync failures from Frederic Barrat
- Increase timeout for detection of AFU mmio hang from Frederic
Barrat
- Handle num_of_processes larger than can fit in the SPA from Ian
Munsie
- Ensure PSL interrupt is configured for contexts with no AFU IRQs
from Ian Munsie
- Add kernel API to allow a context to operate with relocate disabled
from Ian Munsie
- Check periodically the coherent platform function's state from
Christophe Lombard
Freescale:
- Updates from Scott: "Contains 86xx fixes, minor device tree fixes,
an erratum workaround, and a kconfig dependency fix."
* tag 'powerpc-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (192 commits)
powerpc/86xx: Fix PCI interrupt map definition
powerpc/86xx: Move pci1 definition to the include file
powerpc/fsl: Fix build of the dtb embedded kernel images
powerpc/fsl: Fix rcpm compatible string
powerpc/fsl: Remove FSL_SOC dependency from FSL_LBC
powerpc/fsl-pci: Add a workaround for PCI 5 errata
powerpc/fsl: Fix SPI compatible on t208xrdb and t1040rdb
powerpc/powernv/npu: Add PE to PHB's list
powerpc/powernv: Fix insufficient memory allocation
powerpc/iommu: Remove the dependency on EEH struct in DDW mechanism
Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell"
powerpc/eeh: Drop unnecessary label in eeh_pe_change_owner()
powerpc/eeh: Ignore handlers in eeh_pe_reset_and_recover()
powerpc/eeh: Restore initial state in eeh_pe_reset_and_recover()
powerpc/eeh: Don't report error in eeh_pe_reset_and_recover()
Revert "powerpc/powernv: Exclude root bus in pnv_pci_reset_secondary_bus()"
powerpc/powernv/npu: Enable NVLink pass through
powerpc/powernv/npu: Rework TCE Kill handling
powerpc/powernv/npu: Add set/unset window helpers
powerpc/powernv/ioda2: Export debug helper pe_level_printk()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This includes two new updates for the ftrace infrastructure.
- With the changing of the code for filtering events by pid, from a
list of pids to a bitmask, we can now easily implement following
forks. With a new tracing option "event-fork" which, when set,
will have tasks with pids in set_event_pid, when they fork, to have
their child pids added to set_event_pid and the child will be
traced as well.
Note, if "event-fork" is set and a task with its pid in
set_event_pid exits, its pid will be removed from set_event_pid
- The addition of Tom Zanussi's hist triggers. This includes a very
thorough documentatino on how to use the hist triggers with events.
This introduces a quick and easy way to get histogram data from
events and their fields.
Some other cleanups and updates were added as well. Like Masami
Hiramatsu added test cases for the event trigger and hist triggers.
Also I added a speed up of filtering by using a temp buffer when
filters are set"
* tag 'trace-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (45 commits)
tracing: Use temp buffer when filtering events
tracing: Remove TRACE_EVENT_FL_USE_CALL_FILTER logic
tracing: Remove unused function trace_current_buffer_lock_reserve()
tracing: Remove one use of trace_current_buffer_lock_reserve()
tracing: Have trace_buffer_unlock_commit() call the _regs version with NULL
tracing: Remove unused function trace_current_buffer_discard_commit()
tracing: Move trace_buffer_unlock_commit{_regs}() to local header
tracing: Fold filter_check_discard() into its only user
tracing: Make filter_check_discard() local
tracing: Move event_trigger_unlock_commit{_regs}() to local header
tracing: Don't use the address of the buffer array name in copy_from_user
tracing: Handle tracing_map_alloc_elts() error path correctly
tracing: Add check for NULL event field when creating hist field
tracing: checking for NULL instead of IS_ERR()
tracing: Do not inherit event-fork option for instances
tracing: Fix unsigned comparison to zero in hist trigger code
kselftests/ftrace: Add a test for log2 modifier of hist trigger
tracing: Add hist trigger 'log2' modifier
kselftests/ftrace: Add hist trigger testcases
kselftests/ftrace : Add event trigger testcases
...
|
