| Age | Commit message (Collapse) | Author |
|---|
|
RC_TYPE is confusing and it's just the protocol. So rename it.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Since commit 12749b198fa4 ("[media] rc: saa7134: add trailing space for
timely decoding"), the workaround of inserting reset events is no
longer needed.
Note that the initial reset is not needed either; other rc-core drivers
that don't use ir_raw_event_store_edge() never call this at all.
Verified on a HVR-1150 and Raspberry Pi.
Fixes: 3f5c4c73322e ("[media] rc: fix ghost keypresses with certain hw")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The NEC scancode composing and protocol type detection in
ir_nec_decode() is generic enough to be a shared function. Let's create
an inline function in rc-core.h, so that other remote control drivers
can reuse this function to save some code.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
When an ir-spi is registered, you get this message.
rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
"Unspecified device" refers to input_name, which makes no sense for IR
TX only devices. So, rename to device_name.
Also make driver_name const char* so that no casts are needed anywhere.
Now ir-spi reports:
rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Now that rc_register_device() is reorganised, the dev->initialized
hack can be removed. Any driver which calls rc_register_device()
must be prepared for the device to go live immediately.
The dev->initialized commits that are relevant are commit c73bbaa4ec3e
("[media] rc-core: don't lock device at rc_register_device()") and
commit 08aeb7c9a42a ("[media] rc: add locking to fix register/show race").
The original problem was that show_protocols() would access
dev->rc_map.* and various other bits which are now properly
initialized before device_add() is called.
At the same time, remove the bogus "device is being removed" check.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
IR raw transmitter driver type is specified in the enum
rc_driver_type as RC_DRIVER_IR_RAW_TX which includes all those
devices that transmit raw stream of bit to a receiver.
The data are provided by userspace applications, therefore they
don't need any input device allocation, but still they need to be
registered as raw devices.
Suggested-by: Sean Young <sean@mess.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The driver type can be assigned immediately when an RC device
requests to the framework to allocate the device.
This is an 'enum rc_driver_type' data type and specifies whether
the device is a raw receiver or scancode receiver. The type will
be given as parameter to the rc_allocate_device device.
Change accordingly all the drivers calling rc_allocate_device()
so that the device type is specified during the rc device
allocation. Whenever the device type is not specified, it will be
set as RC_DRIVER_SCANCODE which was the default '0' value.
Suggested-by: Sean Young <sean@mess.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add support in rc-core for drivers which implement the wakeup scancode
filter by encoding the scancode using the raw IR encoders. This is by
way of rc_dev::encode_wakeup which should be set to true and
rc_dev::allowed_wakeup_protocols should be set to the raw IR encoders.
We also do not permit the mask to be set as we cannot generate IR
which would match that.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add a callback to raw ir handlers for encoding and modulating a scancode
to a set of raw events. This could be used for transmit, or for
converting a wakeup scancode to a form that is more suitable for raw
hardware wake up filters.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
For IR wakeup, a driver has to program the hardware to wakeup at a
specific IR sequence, so it makes no sense to allow multiple wakeup
protocols to be selected. In the same manner the sysfs interface only
allows one scancode to be provided.
In addition, we need to know the specific variant of the protocol.
In short, these changes are made to the wakeup_protocols sysfs entry:
- list all the protocol variants rather than the protocol groups,
e.g. "nec nec-x nec-32" rather than just "nec".
- only allow one protocol variant to be selected rather than multiple
- wakeup_filter can only be set once a protocol has been selected in
wakeup_protocols.
This is an API change, however the only user of this API is the img-ir,
but the wakeup code was never merged to mainline, so it was never used.
Signed-off-by: Sean Young <sean@mess.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
rc_register_device
Introduce managed versions of both functions.
They allows to simplify the error path in the probe function of
rc drivers, and usually also to simplify the remove function.
New element managed_alloc in struct rc_dev is needed to correctly
handle mixed use, e.g. managed version of rc_register_device and
normal version of rc_allocate_device.
In addition devm_rc_allocate_device sets rc->dev.parent as having a
reference to the parent device might be useful for future extensions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
As warned by linuxdoc[1] tool, using:
$ for i in $(git grep kernel-doc Documentation/media/kapi/|cut -d: -f4); do kernel-lintdoc --sloppy $i; done
include/media/v4l2-dev.h:118 :WARN: function name from comment differs: v4l2_prio_close <--> v4l2_prio_check
include/media/v4l2-mc.h:56 [kernel-doc WARN] : enum name from comment differs: if_vid_dec_index <--> if_vid_dec_pad_index
include/media/v4l2-mc.h:71 [kernel-doc WARN] : enum name from comment differs: if_aud_dec_index <--> if_aud_dec_pad_index
include/media/v4l2-mem2mem.h:396 [kernel-doc WARN] : function name from comment differs: v4l2_m2m_num_src_bufs_ready <--> v4l2_m2m_num_dst_bufs_ready
drivers/media/dvb-core/dvb_math.h:28 [kernel-doc WARN] : function name from comment differs: cintlog2 <--> intlog2
include/media/v4l2-subdev.h:215 [kernel-doc WARN] : struct name from comment differs: s_radio <--> v4l2_subdev_tuner_ops
include/media/v4l2-subdev.h:890 [kernel-doc WARN] : function name from comment differs: v4l2_set_subdevdata <--> v4l2_set_subdev_hostdata
include/media/v4l2-subdev.h:901 [kernel-doc WARN] : function name from comment differs: v4l2_get_subdevdata <--> v4l2_get_subdev_hostdata
drivers/media/dvb-core/dvb_ringbuffer.h:196 [kernel-doc WARN] : function name from comment differs: dvb_ringbuffer_writeuser <--> dvb_ringbuffer_write_user
include/media/videobuf2-core.h:399 [kernel-doc WARN] : struct name from comment differs: vb2_ops <--> vb2_buf_ops
include/media/media-entity.h:132 [kernel-doc ERROR] : duplicate parameter definition 'source'
include/media/media-entity.h:477 [kernel-doc WARN] : function name from comment differs: media_entity_enum_test <--> media_entity_enum_test_and_set
include/media/media-entity.h:535 [kernel-doc WARN] : function name from comment differs: gobj_to_entity <--> gobj_to_pad
include/media/media-entity.h:544 [kernel-doc WARN] : function name from comment differs: gobj_to_entity <--> gobj_to_link
include/media/media-entity.h:553 [kernel-doc WARN] : function name from comment differs: gobj_to_entity <--> gobj_to_intf
include/media/media-entity.h:562 [kernel-doc WARN] : function name from comment differs: gobj_to_entity <--> intf_to_devnode
include/media/rc-core.h:234 [kernel-doc WARN] : function name from comment differs: rc_open <--> rc_close
include/media/v4l2-ctrls.h:397 [kernel-doc WARN] : missing initial short description of 'v4l2_ctrl_handler_init'
include/media/v4l2-dev.h:118 [kernel-doc WARN] : function name from comment differs: v4l2_prio_close <--> v4l2_prio_check
include/media/v4l2-event.h:225 [kernel-doc WARN] : missing initial short description of 'v4l2_src_change_event_subscribe'
[1] https://return42.github.io/linuxdoc/linux.html
The above are real issues at the documentation. On several cases,
caused by cut-and-paste.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
* patchwork: (1492 commits)
[media] cec: always check all_device_types and features
[media] cec: poll should check if there is room in the tx queue
[media] vivid: support monitor all mode
[media] cec: fix test for unconfigured adapter in main message loop
[media] cec: limit the size of the transmit queue
[media] cec: zero unused msg part after msg->len
[media] cec: don't set fh to NULL in CEC_TRANSMIT
[media] cec: clear all status fields before transmit and always fill in sequence
[media] cec: CEC_RECEIVE overwrote the timeout field
[media] cxd2841er: Reading SNR for DVB-C added
[media] cxd2841er: Reading BER and UCB for DVB-C added
[media] cxd2841er: fix switch-case for DVB-C
[media] cxd2841er: fix signal strength scale for ISDB-T
[media] cxd2841er: adjust the dB scale for DVB-C
[media] cxd2841er: provide signal strength for DVB-C
[media] cxd2841er: fix BER report via DVBv5 stats API
[media] mb86a20s: apply mask to val after checking for read failure
[media] airspy: fix error logic during device register
[media] s5p-cec/TODO: add TODO item
[media] cec/TODO: drop comment about sphinx documentation
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The kernel-doc script is now broken if it doesn't find all
exported symbols documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Instead of hardcoding a timeout, let userspace change it dynamically
by adding a s_timeout ops.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
struct ir_raw_event currently has a size of 12 bytes on most (all?)
architectures. This can be reduced to 8 bytes whilst maintaining
full backwards compatibility.
This saves 2KB in size of struct ir_raw_event_ctrl (as element
kfifo is reduced by 512 * 4 bytes) and it allows to copy the
full struct ir_raw_event with a single 64 bit operation.
Successfully tested with the Nuvoton driver and successfully
compile-tested with the ene_ir driver (as it uses the carrier /
duty_cycle elements).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The device initialization completes only after calling
input_register_device(). However, rc_open() can be called while
the device is being registered by the input/evdev core. So, we
can't expect that rc_dev->initialized to be true.
Change the logic to don't require initialized == true at rc_open
and change the type of initialized to be atomic.
this way, we can check for it earlier where it is really needed,
without needing to lock the mutex just for testing it.
Tested with nuvoton_cir driver on a NUC5i7RYB with CIR integrated on it.
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The mutex lock at rc_register_device() was added by commit 08aeb7c9a42a
("[media] rc: add locking to fix register/show race").
It is meant to avoid race issues when trying to open a sysfs file while
the RC register didn't complete.
Adding a lock there causes troubles, as detected by the Kernel lock
debug instrumentation at the Kernel:
======================================================
[ INFO: possible circular locking dependency detected ]
4.5.0-rc3+ #46 Not tainted
-------------------------------------------------------
systemd-udevd/2681 is trying to acquire lock:
(s_active#171){++++.+}, at: [<ffffffff8171a115>] kernfs_remove_by_name_ns+0x45/0xa0
but task is already holding lock:
(&dev->lock){+.+.+.}, at: [<ffffffffa0724def>] rc_register_device+0xb2f/0x1450 [rc_core]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&dev->lock){+.+.+.}:
[<ffffffff8124817d>] lock_acquire+0x13d/0x320
[<ffffffff822de966>] mutex_lock_nested+0xb6/0x860
[<ffffffffa0721f2b>] show_protocols+0x3b/0x3f0 [rc_core]
[<ffffffff81cdaba5>] dev_attr_show+0x45/0xc0
[<ffffffff8171f1b3>] sysfs_kf_seq_show+0x203/0x3c0
[<ffffffff8171a6a1>] kernfs_seq_show+0x121/0x1b0
[<ffffffff81617c71>] seq_read+0x2f1/0x1160
[<ffffffff8171c911>] kernfs_fop_read+0x321/0x460
[<ffffffff815abc20>] __vfs_read+0xe0/0x3d0
[<ffffffff815ae90e>] vfs_read+0xde/0x2d0
[<ffffffff815b1d01>] SyS_read+0x111/0x230
[<ffffffff822e8636>] entry_SYSCALL_64_fastpath+0x16/0x76
-> #0 (s_active#171){++++.+}:
[<ffffffff81244f24>] __lock_acquire+0x4304/0x5990
[<ffffffff8124817d>] lock_acquire+0x13d/0x320
[<ffffffff81717d3a>] __kernfs_remove+0x58a/0x810
[<ffffffff8171a115>] kernfs_remove_by_name_ns+0x45/0xa0
[<ffffffff81721592>] remove_files.isra.0+0x72/0x190
[<ffffffff8172174b>] sysfs_remove_group+0x9b/0x150
[<ffffffff81721854>] sysfs_remove_groups+0x54/0xa0
[<ffffffff81cd97d0>] device_remove_attrs+0xb0/0x140
[<ffffffff81cdb27c>] device_del+0x38c/0x6b0
[<ffffffffa0724b8b>] rc_register_device+0x8cb/0x1450 [rc_core]
[<ffffffffa1326a7b>] dvb_usb_remote_init+0x66b/0x14d0 [dvb_usb]
[<ffffffffa1321c81>] dvb_usb_device_init+0xf21/0x1860 [dvb_usb]
[<ffffffffa13517dc>] dib0700_probe+0x14c/0x410 [dvb_usb_dib0700]
[<ffffffff81dbb1dd>] usb_probe_interface+0x45d/0x940
[<ffffffff81ce7e7a>] driver_probe_device+0x21a/0xc30
[<ffffffff81ce89b1>] __driver_attach+0x121/0x160
[<ffffffff81ce21bf>] bus_for_each_dev+0x11f/0x1a0
[<ffffffff81ce6cdd>] driver_attach+0x3d/0x50
[<ffffffff81ce5df9>] bus_add_driver+0x4c9/0x770
[<ffffffff81cea39c>] driver_register+0x18c/0x3b0
[<ffffffff81db6e98>] usb_register_driver+0x1f8/0x440
[<ffffffffa074001e>] dib0700_driver_init+0x1e/0x1000 [dvb_usb_dib0700]
[<ffffffff810021b1>] do_one_initcall+0x141/0x300
[<ffffffff8144d8eb>] do_init_module+0x1d0/0x5ad
[<ffffffff812f27b6>] load_module+0x6666/0x9ba0
[<ffffffff812f5fe8>] SyS_finit_module+0x108/0x130
[<ffffffff822e8636>] entry_SYSCALL_64_fastpath+0x16/0x76
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&dev->lock);
lock(s_active#171);
lock(&dev->lock);
lock(s_active#171);
*** DEADLOCK ***
3 locks held by systemd-udevd/2681:
#0: (&dev->mutex){......}, at: [<ffffffff81ce8933>] __driver_attach+0xa3/0x160
#1: (&dev->mutex){......}, at: [<ffffffff81ce8941>] __driver_attach+0xb1/0x160
#2: (&dev->lock){+.+.+.}, at: [<ffffffffa0724def>] rc_register_device+0xb2f/0x1450 [rc_core]
In this specific case, some error happened during device init,
causing IR to be disabled.
Let's fix it by adding a var that will tell when the device is
initialized. Any calls before that will return a -EINVAL.
That should prevent the race issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
A default timeout value of 125 ms should work for all decoders.
Declare a constant to help standardize its' use.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
|
|
Warning(.//include/media/rc-core.h:178): No description found for parameter 's_rx_carrier_range'
Warning(.//include/media/rc-core.h:178): Excess struct/union/enum/typedef member 's_rx_carrier' description in 'rc_dev'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
This reverts commit 9869da5bacc5c9b865a183bd36c04be76cdd325d.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This reverts commit 0d830b2d1295fee82546d57185da5a6604f11ae2.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
sysfs filter callback"
This reverts commit da7ee60b03bd66bb10974d7444aa444de6391312.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch changes rc-core to use the kernel facilities that are already
available for handling unique numbers instead of rolling its own bitmap
stuff.
Signed-off-by: David Härdeman <david@hardeman.nu>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The current definition is weird, and produce lots of sparse
warnings:
drivers/media/i2c/cx25840/cx25840-ir.c:448 txclk_tx_s_max_pulse_width() warn: impossible condition '(ns > 4294967295) => (0-u32max > u32max)'
drivers/media/i2c/cx25840/cx25840-ir.c:461 rxclk_rx_s_max_pulse_width() warn: impossible condition '(ns > 4294967295) => (0-u32max > u32max)'
drivers/media/i2c/cx25840/cx25840-ir.c:706 cx25840_ir_rx_read() warn: impossible condition '(v > 4294967295) => (0-u32max > u32max)'
drivers/media/pci/ivtv/ivtv-queue.c:145 ivtv_queue_move() error: we previously assumed 'steal' could be null (see line 138)
drivers/media/rc/streamzap.c:155 sz_push_full_pulse() warn: impossible condition '(rawir.duration > 4294967295) => (0-u32max > u32max)'
drivers/media/rc/streamzap.c:169 sz_push_full_pulse() warn: impossible condition '(rawir.duration > 4294967295) => (0-u32max > u32max)'
drivers/media/rc/redrat3.c:325 redrat3_us_to_len() warn: impossible condition '(microsec > 4294967295) => (0-u32max > u32max)'
drivers/media/rc/redrat3.c:383 redrat3_process_ir_data() warn: impossible condition '(rawir.duration > 4294967295) => (0-u32max > u32max)'
drivers/media/usb/pvrusb2/pvrusb2-hdw.c:3676 pvr2_send_request_ex() error: we previously assumed 'write_data' could be null (see line 3648)
drivers/media/usb/pvrusb2/pvrusb2-hdw.c:3829 pvr2_send_request_ex() error: we previously assumed 'read_data' could be null (see line 3649)
drivers/media/pci/cx23885/cx23888-ir.c:463 txclk_tx_s_max_pulse_width() warn: impossible condition '(ns > 4294967295) => (0-u32max > u32max)'
drivers/media/pci/cx23885/cx23888-ir.c:476 rxclk_rx_s_max_pulse_width() warn: impossible condition '(ns > 4294967295) => (0-u32max > u32max)'
drivers/media/pci/cx23885/cx23888-ir.c:696 cx23888_ir_rx_read() warn: impossible condition '(v > 4294967295) => (0-u32max > u32max)'
Use a more realistic value for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
filter callback
Nuvoton-cir utilizes the encoding capabilities of rc-core to convert
scancodes from user space to pulse/space format understood by the
underlying hardware.
Converted samples are then written to the wakeup fifo along with other
necessary configuration to enable wake up functionality.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james@albanarts.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add support in rc-core for drivers which implement the wakeup scancode
filter by encoding the scancode using the raw IR encoders. This is by
way of rc_dev::encode_wakeup which should be set to true to make the
allowed wakeup protocols the same as the set of raw IR encoders.
As well as updating the sysfs interface to know which wakeup protocols
are allowed for encode_wakeup drivers, also ensure that the IR
decoders/encoders are loaded when an encode_wakeup driver is registered.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add a callback to raw ir handlers for encoding and modulating a scancode
to a set of raw events. This could be used for transmit, or for
converting a wakeup scancode filter to a form that is more suitable for
raw hardware wake up filters.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The hole point of IR_dprintk() is that, once a level is
given at debug parameter, all enabled IR parsers will show their
debug messages.
While converting it to dynamic_printk might be a good idea,
right now it just makes very hard to debug the drivers, as
one needs to both pass debug=1 or debug=2 to rc-core and
to use the dynamic printk to enable all the desired lines.
That doesn't make sense!
So, revert to the old way, as a single line is changed,
and the debug parameter will now work as expected.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
We already have dev->scancode_filter and dev->scancode_wakeup_filter
so rename dev->scanmask to dev->scancode_mask for consistency.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The basic API of rc-core used to be:
dev = rc_allocate_device();
dev->x = a;
dev->y = b;
dev->z = c;
rc_register_device();
which is a pretty common pattern in the kernel, after the introduction of
protocol arrays the API looks something like:
dev = rc_allocate_device();
dev->x = a;
rc_set_allowed_protocols(dev, RC_BIT_X);
dev->z = c;
rc_register_device();
There's no real need for the protocols to be an array, so change it
back to be consistent (and in preparation for the following patches).
[m.chehab@samsung.com: added missing changes at some files]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.
This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.
[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The generic scancode filtering has questionable value and makes it
impossible to determine from userspace if there is an actual
scancode hw filter present or not.
So revert the generic parts.
Based on a patch from James Hogan <james.hogan@imgtec.com>, but this
version also makes sure that only the valid sysfs files are created
in the first place.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Overloading dev->s_filter to do two different functions (set wakeup filters
and generic hardware filters) makes it impossible to tell what the
hardware actually supports, so create a separate dev->s_wakeup_filter and
make the distinction explicit.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Add a wakeup_protocols sysfs file which controls the new
rc_dev::enabled_protocols[RC_FILTER_WAKEUP], which is the mask of
protocols that are used for the wakeup filter.
A new RC driver callback change_wakeup_protocol() is called to change
the wakeup protocol mask.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Only a single allowed and enabled protocol mask currently exists in
struct rc_dev, however to support a separate wakeup filter protocol two
of each are needed, ideally as an array.
Therefore make both rc_dev::allowed_protos and rc_dev::enabled_protocols
arrays, update all users to reference the first element
(RC_FILTER_NORMAL), and add a couple more helper functions for drivers
to use for setting the allowed and enabled wakeup protocols.
We also rename allowed_protos to allowed_protocols while we're at it,
which is more consistent with enabled_protocols.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The allowed and enabled protocol masks need to be expanded to be per
filter type in order to support wakeup filter protocol selection. To
ease that process abstract access to the rc_dev::allowed_protos and
rc_dev::enabled_protocols members with inline functions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
There are several left overs with my old email address.
Remove their occurrences and add myself at CREDITS, to
allow people to be able to reach me on my new addresses.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Add and document a generic sysfs based scancode filtering interface for
making use of IR data matching hardware to filter out uninteresting
scancodes. Two filters exist, one for normal operation and one for
filtering scancodes which are permitted to wake the system from suspend.
The following files are added to /sys/class/rc/rc?/:
- filter: normal scancode filter value
- filter_mask: normal scancode filter mask
- wakeup_filter: wakeup scancode filter value
- wakeup_filter_mask: wakeup scancode filter mask
A new s_filter() driver callback is added which must arrange for the
specified filter to be applied at the right time. Drivers can convert
the scancode filter into a raw IR data filter, which can be applied
immediately or later (for wake up filters).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
This patch adds user count to rc_dev structure, the reason to add this
new member is to allow other code like lirc to open rc device directly.
In the existing code, rc device is only opened by input subsystem which
works ok if we have any input drivers to match. But in case like lirc
where there will be no input driver, rc device will be never opened.
Having this user count variable will be usefull to allow rc device to be
opened from code other than rc-main.
This patch also adds rc_open and rc_close functions for other drivers
like lirc to open and close rc devices. This functions safely increment
and decrement the user count. Other driver wanting to open rc device
should call rc_open and rc_close, rather than directly modifying the
rc_dev structure.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
store_protocols() treats dev->rc_map.rc_type as a bitmap which is wrong for
two reasons. First of all, it is pretty bogus to change the protocol type of
the keymap just because the hardware has been asked to decode a different
protocol.
Second, dev->rc_map.rc_type is an enum (i.e. a single protocol) as pointed
out by James Hogan <james.hogan@imgtec.com>.
Fix both issues by introducing a separate enabled_protocols member to
struct rc_dev.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The RC_TYPE_* defines are currently used both where a single protocol is
expected and where a bitmap of protocols is expected.
Functions like rc_keydown() and functions which add/remove entries to the
keytable want a single protocol. Future userspace APIs would also
benefit from numeric protocols (rather than bitmap ones). Keytables are
smaller if they can use a small(ish) integer rather than a bitmap.
Other functions or struct members (e.g. allowed_protos,
enabled_protocols, etc) accept multiple protocols and need a bitmap.
Using different types reduces the risk of programmer error. Using a
protocol enum whereever possible also makes for a more future-proof
user-space API as we don't need to worry about a sufficient number of
bits being available (e.g. in structs used for ioctl() calls).
The use of both a number and a corresponding bit is dalso one in e.g.
the input subsystem as well (see all the references to set/clear bit when
changing keytables for example).
This patch separate the different usages in preparation for
upcoming patches.
Where a single protocol is expected, enum rc_type is used; where one or more
protocol(s) are expected, something like u64 is used.
The patch has been rewritten so that the format of the sysfs "protocols"
file is no longer altered (at the loss of some detail). The file itself
should probably be deprecated in the future though.
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Macros coded with if statements should be do { if... } while (0)
so the macros can be used in other if tests.
Use ##__VA_ARGS__ for variadic macro as well.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Durations can never be negative, so it makes sense to consistently use
unsigned int for LIRC transmission. Contrary to the initial impression,
this shouldn't actually change the userspace API.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When device_add is called in rc_register_device, the rc sysfs nodes show
up, and there's a window in which ir-keytable can be launched via udev
and trigger a show_protocols call, which runs without various rc_dev
fields filled in yet. Add some locking around registration and
store/show_protocols to prevent that from happening.
The problem manifests thusly:
[64692.957872] BUG: unable to handle kernel NULL pointer dereference at 0000000000000090
[64692.957878] IP: [<ffffffffa036a4c1>] show_protocols+0x47/0xf1 [rc_core]
[64692.957890] PGD 19cfc7067 PUD 19cfc6067 PMD 0
[64692.957894] Oops: 0000 [#1] SMP
[64692.957897] last sysfs file: /sys/devices/pci0000:00/0000:00:03.1/usb3/3-1/3-1:1.0/rc/rc2/protocols
[64692.957902] CPU 3
[64692.957903] Modules linked in: redrat3(+) ir_lirc_codec lirc_dev ir_sony_decoder ir_jvc_decoder ir_rc6_decoder ir_rc5_decoder rc_hauppauge ir_nec
_decoder rc_core ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables snd_emu10k1_synth snd_emux_synth snd_seq_virmidi snd_seq_mi
di_event snd_seq_midi_emul snd_emu10k1 snd_rawmidi snd_ac97_codec ac97_bus snd_seq snd_pcm snd_seq_device snd_timer snd_page_alloc snd_util_mem pcsp
kr tg3 snd_hwdep emu10k1_gp snd amd64_edac_mod gameport edac_core soundcore edac_mce_amd k8temp shpchp i2c_piix4 lm63 e100 mii uinput ipv6 raid0 rai
d1 ata_generic firewire_ohci pata_acpi firewire_core crc_itu_t sata_svw pata_serverworks floppy radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core
[last unloaded: redrat3]
[64692.957949] [64692.957952] Pid: 12265, comm: ir-keytable Tainted: G M W 2.6.39-rc6+ #2 empty empty/TYAN Thunder K8HM S3892
[64692.957957] RIP: 0010:[<ffffffffa036a4c1>] [<ffffffffa036a4c1>] show_protocols+0x47/0xf1 [rc_core]
[64692.957962] RSP: 0018:ffff880194509e38 EFLAGS: 00010202
[64692.957964] RAX: 0000000000000000 RBX: ffffffffa036d1e0 RCX: ffffffffa036a47a
[64692.957966] RDX: ffff88019a84d000 RSI: ffffffffa036d1e0 RDI: ffff88019cf2f3f0
[64692.957969] RBP: ffff880194509e68 R08: 0000000000000002 R09: 0000000000000000
[64692.957971] R10: 0000000000000002 R11: 0000000000001617 R12: ffff88019a84d000
[64692.957973] R13: 0000000000001000 R14: ffff8801944d2e38 R15: ffff88019ce5f190
[64692.957976] FS: 00007f0a30c9a720(0000) GS:ffff88019fc00000(0000) knlGS:0000000000000000
[64692.957979] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[64692.957981] CR2: 0000000000000090 CR3: 000000019a8e0000 CR4: 00000000000006e0
[64692.957983] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[64692.957986] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[64692.957989] Process ir-keytable (pid: 12265, threadinfo ffff880194508000, task ffff88019a9fc720)
[64692.957991] Stack:
[64692.957992] 0000000000000002 ffffffffa036d1e0 ffff880194509f58 0000000000001000
[64692.957997] ffff8801944d2e38 ffff88019ce5f190 ffff880194509e98 ffffffff8131484b
[64692.958001] ffffffff8118e923 ffffffff810e9b2f ffff880194509e98 ffff8801944d2e18
[64692.958005] Call Trace:
[64692.958014] [<ffffffff8131484b>] dev_attr_show+0x27/0x4e
[64692.958014] [<ffffffff8118e923>] ? sysfs_read_file+0x94/0x172
[64692.958014] [<ffffffff810e9b2f>] ? __get_free_pages+0x16/0x52
[64692.958014] [<ffffffff8118e94c>] sysfs_read_file+0xbd/0x172
[64692.958014] [<ffffffff8113205e>] vfs_read+0xac/0xf3
[64692.958014] [<ffffffff8113347b>] ? fget_light+0x3a/0xa1
[64692.958014] [<ffffffff811320f2>] sys_read+0x4d/0x74
[64692.958014] [<ffffffff814c19c2>] system_call_fastpath+0x16/0x1b
Its a bit difficult to reproduce, but I'm fairly confident this has
fixed the problem.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The ene_ir driver was using a private define of MS_TO_NS, which is meant
to be microseconds to nanoseconds. The mceusb driver copied it,
intending to use is a milliseconds to microseconds. Lets move the
defines to a common location, expand and standardize them a touch, so
that we now have:
MS_TO_NS - milliseconds to nanoseconds
MS_TO_US - milliseconds to microseconds
US_TO_NS - microseconds to nanoseconds
Reported-by: David Härdeman <david@hardeman.nu>
CC: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fix some minor comments etc which are leftover from the old naming scheme.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The struct that describes a rc mapping had an weird and long name.
We should properly name it, to make easier for developers to work
with it, and to avoid confusion.
Basically, generated by this script:
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_scancode_table,rc_map,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_tab,rc_map,g <$i >a && mv a $i; done
(and manually fixed where needed)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,IR_TYPE,RC_TYPE,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_type,rc_type,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
